Textile Structure
how cloth is put together
Concept

Shear — where it appears

Two thread systems rotating at their crossings so the cloth's cells go from square to rhombic, at no cost in thread length. It is the deformation that lets a flat cloth take a curved surface, and it ends at the angle where the threads jam against their neighbours.

Named by 6 essays across 2 fields — each of them below, with the objects they name alongside it.

A trellis sheared 30°. The net at an angle, with every thread segment exactly the length it started at. The extension along the diagonal is the bias stretch, and it is a change of shape rather than a change of length.

The bias is a mechanism

Cloth cut at forty-five degrees stretches by a third and springs back, while the threads in it stretch by nothing at all. Almost every explanation given for this is wrong, and the right one is not about elasticity.

mechanics · Bias How far the bias goes, and where it stops. Extension along the bias against shear angle, with the angle at which the threads jam marked for three settings. The curve is geometry and so is the wall — a more closely set cloth reaches it sooner.

The locking angle

The bias runs out at an angle that yarn diameter and thread spacing decide between them. It is the number behind whether a cloth will go round a curve, and it has nothing to do with how strong the fabric is.

mechanics · Bias A ratio that will not hold still. The exchange rate between the two directions for 4 cloths, against how far each has been extended along the warp. Every curve is above one half everywhere it is drawn, and every curve rises — so a single number for a cloth's ratio has to name the state it was read at, which a material's ratio does not.

A cloth's Poisson ratio is not a material's

The ratio of a cloth's contraction to its extension has a name everywhere else in mechanics, and it breaks every rule the name comes with — above one half on all eight cloths measured, doubling across a four per cent span, and not reciprocal between the two directions.

mechanics · Tensile How much of the curvature a cloth can take without being cut. The dart angle a spherical cap still demands after the fabric's own shear has absorbed what it can, against how closely the cloth is set. The total the cap demands is fixed by Gauss–Bonnet and is the same for all of them; what changes is how much of it the trellis can supply before its threads jam. An open cloth drapes a hemisphere with no dart at all; a closely set one has to be cut from the start.

A hemisphere costs one full turn

The total angle a pattern must remove to cover a hemisphere is exactly 360 degrees, and it is the same for a hat and for a stadium dome. What changes with the fabric is how much of that the cloth can supply by shearing instead of by being cut — and that is a property of the sett, computed from the angle at which its threads jam.

applied · Cutting Shrinkage from wetting, cloth by cloth. The change in each cloth's relaxed construction when its threads swell by 20% across and 1.2% along. Both states are least-energy states of their own constant-thread-length locus, which is the only comparison the locus admits: its minimum is a state at its own sett, so it may be compared with another minimum and not with a quoted construction. Positive is smaller. Every cloth that has a wet state closes up except the cheesecloth, which opens by half a per cent because the fibre's extra hundredth of length outruns the extra crimp a thicker partner costs. What the bars cannot show is the three cloths that are missing, which have no wet state at all.

A garment is cut dry and worn wet

A cutting allowance is one number and the thing it allows for is two, in two directions. Worse: when the two directions differ, a panel cut on the bias does not merely shrink — it rotates, by half a degree for an ordinary poplin, which is nine and a half millimetres of skew across a metre and is invisible to a tape measure.

applied · Cutting The shear a dome demands, against how far round it the cloth reaches. A flat sheet of inextensible threads takes a double curvature only by shearing, and the shear it needs depends on how far round the dome it has to reach rather than on how big the dome is — a knee, a shoulder and a beach ball demand exactly the same at the same fraction of their own radius. The horizontal line is the locking angle for a sheeting, where the threads are touching side by side and the mechanism has nowhere left to go. Reaching one radius round takes the cloth to 85% of that, and reaching 1.2 radii passes it. What the plot cannot show is the frictional part: a shear well inside the locking angle is still a shear at crossings friction is holding, so a knee that is domed a thousand times keeps a little of each one.

A knee is a dome imposed a thousand times

A flat sheet of inextensible threads takes a double curvature only by shearing, and how much shear it needs depends on how far round the dome it has to reach — not on how big the dome is. So a knee and a beach ball demand the same, and a trouser knee covered to its own equator is at 85 per cent of the angle at which the threads touch side by side.

applied · Damage

Named alongside it

The objects these essays reach for when they reach for this one.

InextensibleLocking angleBiasDartDrapeKinematicsTrellisAllowanceAnisotropyBaggingConstant length locusCover

All concepts