Textile Structure
how cloth is put together
Concept

Drape — where it appears

How a cloth falls under its own weight, which is a bending stiffness and an areal density and nothing about the interlacement directly. Two tests measure it and answer different questions, and the trade quotes them as one.

Named by 13 essays across 3 fields — each of them below, with the objects they name alongside it.

Where the floats are in the 5-end satin. Every longest run of warp on the face, marked. A float is smooth because nothing interrupts it, which is the same reason it snags: there is a length of thread lying on the surface with nothing holding it down.

The float decides

How far a thread runs on the face before it goes under is one number, and it sits behind lustre, drape, snagging, abrasion, tear strength and how densely the cloth can be set. Almost nothing else in the subject has that reach.

weaves · Float How far the bias goes, and where it stops. Extension along the bias against shear angle, with the angle at which the threads jam marked for three settings. The curve is geometry and so is the wall — a more closely set cloth reaches it sooner.

The locking angle

The bias runs out at an angle that yarn diameter and thread spacing decide between them. It is the number behind whether a cloth will go round a curve, and it has nothing to do with how strong the fabric is.

mechanics · Bias A cloth laid over a sphere. Every thread segment is exactly one pitch and none has stretched. What has changed is the angle at each crossing, and the amount is decided by the surface — a developable one costs nothing and a curved one costs more the further the cloth goes.

Why clothes need darts

A flat cloth goes round a cylinder for nothing and cannot go round a sphere at all without shearing. The amount of shear is decided by the curvature, and when it exceeds what the threads allow, something has to be cut out.

mechanics · Drape A cloth laid over a sphere. Every thread segment is exactly one pitch and none has stretched. What has changed is the angle at each crossing, and the amount is decided by the surface — a developable one costs nothing and a curved one costs more the further the cloth goes.

Shear locking in a composite preform

Laying a woven reinforcement over a mould is the bias mechanism doing useful work, and it stops dead at the angle where the threads jam. Where the cloth wrinkles is a geometric prediction with a radius attached.

mechanics · Bias What the drape coefficient answers to. The drape coefficient against the number of folds, and against how far the hem has come in. Over the range a real specimen shows, the fold count barely moves it; the hem radius moves it across almost its whole range.

A drape coefficient is one number for a directional thing

A fabric bends more easily one way than the other — a factor of two is ordinary. The drape test reports a single percentage, and the quantity that carries the directionality is the fold count, which the coefficient is almost blind to.

mechanics · Drape Wrinkles 127 mm apart. A 300 mm width of a 120 g/m² cloth whose bending length is 20 mm, held under 5 newtons per metre across it and compressed. It cannot carry the compression in the plane, so it leaves the plane, at a wavelength the bending rigidity and the tension settle between them: 127 mm, which is 2.4 wrinkles across the width. The amplitude is drawn and is not computed — this arithmetic sets the spacing and says nothing about the depth.

A cloth cannot carry a push

The net model that runs this site's mechanics has no bending stiffness at all, so it buckles under any compression whatever, into wrinkles of any wavelength whatever. What picks the wavelength is the competition the net leaves out — and the answer is a quarter power, which is why a wrinkle is so hard to change.

mechanics · Buckling The number the drape test does not record. A 150 mm specimen over a 90 mm pedestal, for fabrics from limp to stiff. The curve is the fold count the buckling argument predicts — three quarters of a power of the specimen's radius over its own bending length — and it runs from 2 folds to 11. The number beside each mark is the drape coefficient the same specimen would report, which moves by a few points across the whole range.

The nodes a drape test throws away

A drape test lays a circular specimen over a pedestal, photographs the shadow and reports one number. The specimen also falls into a definite number of folds, which is a buckling mode set by the fabric's own bending length — and the standard method observes it, does not record it, and reports the number it is least sensitive to.

mechanics · Buckling The two calculations a yarn's stiffness admits. A bundle of 9 fibres bent with the fibres free to slide and with them locked together. Free, the rigidity is the sum of the fibres': 0.00141 N·mm² for a 30 tex cotton yarn. Locked, it is the fourth power of the yarn's own diameter: 0.689. The ratio is the fibre count over the square of the packing factor, 490, and nine fibres are drawn where the yarn has 176. What the drawing cannot show is where a real yarn sits between them, which is a question about friction rather than about fibre.

A yarn's stiffness is a bracket, not a number

Two calculations are available for how stiff a thread is in bending, and both are exact. One treats the fibres as free to slide and gives the sum of their stiffnesses; the other treats them as locked and gives a solid rod. They differ by the fibre count, which for an ordinary cotton yarn is a factor of five hundred — and no measurement of the fibre narrows it by anything at all.

mechanics · Yarn stiffness The load–extension curve, computed from a stiffness. The tension in one end of a sheeting against how far the cloth has been extended, computed as the slope of its bending energy along its own constant-thread-length locus. The curve passes through zero at the state of least energy, which is where an unloaded cloth sits, and rises either side of it. What the curve cannot show is what happens after the crimp runs out: past the end of the locus the load is carried by stretching yarn rather than by straightening it, and that is a modulus three orders of magnitude higher and a different figure.

The locus gets a force

This site has drawn the set of states a cloth can reach without stretching any yarn, and has never been able to say which of them it is in or what it would cost to move. Both questions are one derivative of a bending energy — and the answer explains the flat start every fabric's load–extension curve has, which is not slack yarn but a symmetry.

mechanics · Tensile The shear a dome demands, against how far round it the cloth reaches. A flat sheet of inextensible threads takes a double curvature only by shearing, and the shear it needs depends on how far round the dome it has to reach rather than on how big the dome is — a knee, a shoulder and a beach ball demand exactly the same at the same fraction of their own radius. The horizontal line is the locking angle for a sheeting, where the threads are touching side by side and the mechanism has nowhere left to go. Reaching one radius round takes the cloth to 85% of that, and reaching 1.2 radii passes it. What the plot cannot show is the frictional part: a shear well inside the locking angle is still a shear at crossings friction is holding, so a knee that is domed a thousand times keeps a little of each one.

A knee is a dome imposed a thousand times

A flat sheet of inextensible threads takes a double curvature only by shearing, and how much shear it needs depends on how far round the dome it has to reach — not on how big the dome is. So a knee and a beach ball demand the same, and a trouser knee covered to its own equator is at 85 per cent of the angle at which the threads touch side by side.

applied · Damage Which end of the bracket a thread in cloth is at. A yarn bends as a solid rod while its fibres cannot slide and as a loose bundle once they can, and the crossover is a curvature: the coherent state demands an axial force in the outer fibre that has to be built up by friction under the twist's own radial pressure. The curves are the crossover radius against twist at four contact efficiencies, the top one being 1.0 — the claim that fibres touch along their whole length, which nobody makes. The rule at the bottom is the radius a thread is bent to by its own crimp in a cloth, about 0.25 mm. Every curve is above the rule by at least 19-fold, so a thread in cloth is at the free end of its bracket at every twist and every efficiency, and the collection's habit of using the lower bound is a result rather than a convention.

Twist decides where in the bracket

A yarn's bending rigidity can only be bracketed, and the bracket is three hundred wide. What decides where a yarn sits in it is whether its fibres can slide — and for a thread bent by its own crimp in a cloth, the answer is not close.

mechanics · Yarn stiffness How hard a fabric is to bend, per unit width. Bending rigidity in micronewton metres per unit width, computed the same way for eight woven cloths and for a jersey in each of its two directions: the yarn's own rigidity, times the length of yarn per unit area, times the fourth power of the cosine of the angle each element makes with the bending direction. The knit lands inside the band of the woven cloths rather than below it, which is worth knowing because a knit is usually called the softer fabric. It is not softer to bend; it is softer to stretch, by three decades. What it does have is direction: 2.17 to one between its two axes, where a balanced plain weave is near one, and the soft axis is the one a jersey rolls about at its top and bottom edges.

A knit bends more easily along its courses

A jersey is not a soft fabric to bend. Computed the same way as this collection's woven cloths it lands inside their band, at the limp end — and the useful number is not the magnitude but the direction: two point two to one between its two axes, with the soft one being the axis it rolls about.

mechanics · Knit What flattening a section does to the ratio of the two stiffnesses. C/B is 2G/E for a circular section, because a circle's polar second moment is exactly twice its flexural one. A flattened section has two different flexural moments — easy about the long axis, hard about the short one — and the polar moment is still their sum, which is the perpendicular axis theorem and holds for any section whatever. So a flattened thread has three constants rather than two, and the multiplier on C/B depends on which way it is being bent. At the 0.78 a knitted fabric's own geometry demands, the easy direction multiplies the ratio by 1.322 and the hard one by 0.804. A knitted loop bends in the easy direction, so the collection's headline ratio is a lower bound for a yarn in cloth.

The section that changes both stiffnesses

A thread's two rigidities are in the ratio 2G/E, and that is a fact about a circular section: a circle's polar second moment is exactly twice its flexural one. A yarn in cloth is not circular, so a yarn in cloth has three constants rather than two — and the ratio a whole ladder rests on is a lower bound.

mechanics · Contact

Named alongside it

The objects these essays reach for when they reach for this one.

Bending rigidityAnisotropyBending lengthSpecificationWrinkleBucklingCantileverCrimpDartDrape coefficientFlexural rigidityFriction

All concepts