Textile Structure
how cloth is put together
Concept

Buckling — where it appears

Leaving the plane rather than carrying a compression, which is what a fabric does under any push at all because it has almost no stiffness in its own plane. The amplitude follows from the surplus length by a square root, which is why a relief made at the loom is deeper than one made in the finishing.

Named by 12 essays across 5 fields — each of them below, with the objects they name alongside it.

Wrinkles 127 mm apart. A 300 mm width of a 120 g/m² cloth whose bending length is 20 mm, held under 5 newtons per metre across it and compressed. It cannot carry the compression in the plane, so it leaves the plane, at a wavelength the bending rigidity and the tension settle between them: 127 mm, which is 2.4 wrinkles across the width. The amplitude is drawn and is not computed — this arithmetic sets the spacing and says nothing about the depth.

A cloth cannot carry a push

The net model that runs this site's mechanics has no bending stiffness at all, so it buckles under any compression whatever, into wrinkles of any wavelength whatever. What picks the wavelength is the competition the net leaves out — and the answer is a quarter power, which is why a wrinkle is so hard to change.

mechanics · Buckling The number the drape test does not record. A 150 mm specimen over a 90 mm pedestal, for fabrics from limp to stiff. The curve is the fold count the buckling argument predicts — three quarters of a power of the specimen's radius over its own bending length — and it runs from 2 folds to 11. The number beside each mark is the drape coefficient the same specimen would report, which moves by a few points across the whole range.

The nodes a drape test throws away

A drape test lays a circular specimen over a pedestal, photographs the shadow and reports one number. The specimen also falls into a definite number of folds, which is a buckling mode set by the fabric's own bending length — and the standard method observes it, does not record it, and reports the number it is least sensitive to.

mechanics · Buckling Float lengths in a honeycomb. The same draft twice. On the left, filled where the warp is on the face — which is all point paper says. On the right, every intersection shaded by the length of the float it belongs to, from one at the palest to 6 at the strongest. The gradient on the right is the whole mechanism of a relief weave and it is invisible on the left.

A honeycomb gets its cells in the wash

The obvious mechanism is take-up on the loom, and the arithmetic says it is wrong: every end of a diamond passes through the long floats and the tight ones alike. What is left is finishing, and a cell is a region that wanted to shrink less than the cloth around it.

weaves · Texture weaves A seersucker in section. A seersucker in section across four stripes, at a feed ratio of 1.30 — the slack warp let off 30 per cent faster than the tight one — over a 6.0 mm stripe. The surplus has nowhere to go in the plane, so it buckles, and the standard small-amplitude result gives 2.09 mm of rise, which is 4.2 times the cloth's own thickness of 0.500 mm. Nothing has to relax for this to appear: unlike a honeycomb, a seersucker comes off the loom already puckered, and washing deepens it rather than creating it. What the drawing cannot show is that the buckle's shape is an assumption — a sinusoid pinned at the stripe's edges — while its amplitude follows from the surplus and the half-wavelength alone.

A seersucker is made at the loom

Every other relief weave in this collection gets its shape after the loom, from a difference of crimp between two regions of a few per cent. A seersucker's surplus is thirty per cent and is put in as the cloth is woven — an order of magnitude more, which the square root turns into a factor of four in depth and no more than that.

weaves · Texture weaves A slack twisted yarn takes a coil of one size. A 20 tex cotton at 1400 turns a metre. Its own torque is 2.060 µN·mm at the free bound, and a rod under tension T is stable while its torque stays under 2·√(B·T). Below that tension the straight state stops being a minimum and the thread wraps on itself at a radius of 0.91 mm. That radius is 2B/M, which is 2/(r·ω) once the torque is written out: it depends on the twist and on the ratio of the two stiffnesses, and on neither stiffness itself.

A crepe is a yarn that will not lie still

A crepe cloth's pebbled surface is the yarn's own torque acting on a cloth that cannot resist it. The instability that makes a slack yarn snarl says how large the pebbles should be, and the answer is a millimetre — which is what a crepe looks like.

pattern · Variation A slack twisted yarn takes a coil of one size. A 20 tex cotton at 800 turns a metre. Its own torque is 1.177 µN·mm at the free bound, and a rod under tension T is stable while its torque stays under 2·√(B·T). Below that tension the straight state stops being a minimum and the thread wraps on itself at a radius of 1.59 mm. That radius is 2B/M, which is 2/(r·ω) once the torque is written out: it depends on the twist and on the ratio of the two stiffnesses, and on neither stiffness itself.

Why a slack yarn snarls

Let go of a twisted thread and it wraps on itself. That is not the yarn being badly behaved: it is a buckling, it has a criterion, and the criterion turns a nuisance into an instrument for measuring the one constant this collection cannot pin down.

setting · Twist How much of a yarn has to hang before it stops snarling. The tension a 20 tex cotton needs to stay straight, at each twist level, expressed as the length of the yarn's own weight that would supply it. The two curves are the two ends of the stiffness bracket: the fibres free to slide, and the section coherent. At 800 turns a metre they are 1.9 metres and 616. Anybody who has let go of a twisted yarn knows which of those is right, which makes this one of very few places where the bracket can be closed from the everyday end. Both rise as the square of the twist, because the torque does and the criterion is quadratic in it.

How much yarn has to hang

The tension a thread needs to stay straight, converted into the only unit anybody has an intuition for: the length of the yarn's own weight. One bound says two metres and the other says six hundred, and everybody who has handled thread already knows which.

setting · Twist A slack twisted yarn takes a coil of one size. A 20 tex cotton at 800 turns a metre. Its own torque is 1.177 µN·mm at the free bound, and a rod under tension T is stable while its torque stays under 2·√(B·T). Below that tension the straight state stops being a minimum and the thread wraps on itself at a radius of 1.59 mm. That radius is 2B/M, which is 2/(r·ω) once the torque is written out: it depends on the twist and on the ratio of the two stiffnesses, and on neither stiffness itself.

A snarl comes in one size

The radius a twisted thread coils to is twice its bending rigidity over its torque. Write the torque out and the bending rigidity cancels completely, leaving a number that depends on the twist and on the ratio of two stiffnesses — and on nothing else about the yarn at all.

setting · Twist How much of a yarn has to hang before it stops snarling. The tension a 20 tex cotton needs to stay straight, at each twist level, expressed as the length of the yarn's own weight that would supply it. The two curves are the two ends of the stiffness bracket: the fibres free to slide, and the section coherent. At 800 turns a metre they are 1.9 metres and 616. Anybody who has let go of a twisted yarn knows which of those is right, which makes this one of very few places where the bracket can be closed from the everyday end. Both rise as the square of the twist, because the torque does and the criterion is quadratic in it.

What a high-twist yarn costs a cloth

Twist buys strength up to a point and then loses it, and everything else it does is a cost. A crepe twist is chosen knowing that, and the trade's twist limits are a balance among five quantities that this collection can now put beside one another.

setting · Twist An inflated tube in section at 0.5, 1, 1.6 times its wrinkling moment. The cross-section of an inflated tube of 100 mm radius at 50 kPa, bent by 0.5 times, 1 times, 1.6 times its wrinkling moment of 78.5 N·m, with the outside of the bend at the top. Each stroke is the wall's axial tension at that point: the pressure's even 2.5 kN/m with the bending's cosine added. At half the wrinkling moment the inside is still in tension; at the wrinkling moment it falls to nothing; past it the inside has gone slack over a dashed arc and the rest carries both the pressure's end force and the moment. What the drawing cannot show is the wrinkles themselves, whose wavelength a cloth's bending stiffness decides and this section leaves out.

An inflated beam wrinkles at a moment with no cloth in it

An air-filled tube can be used as a beam because the pressure pulls its cloth taut along its length, and a cloth that cannot carry a push can carry a bending moment for exactly as long as that pull outweighs it. The inside of the bend goes slack at πpr³/2 and the tube folds at πpr³ — seventy-nine and a hundred and fifty-seven newton metres for a tube a fifth of a metre across at half a bar — and there is no property of the cloth in either. The cloth decides how far the beam bends on the way, and how much pressure it can be pumped to.

applied · Membrane Where an air arch first wrinkles under snow over the whole span. A semicircular air arch 4 m across, pinned at both feet, of a tube 200 mm across at 50 kPa, under snow over the whole span; beside it, unrolled from the left foot to the right, the share of the tube's wrinkling budget πpr³/2 spent at each section when the first wrinkle forms, with the thrust's part, N·r/2, shaded darker. The first wrinkle forms 25° above the right foot, at 167 N per metre of span, where the moment of 60.2 N·m compresses the inside of the curve and the thrust is 336 N; there the thrust has taken 21 per cent of the budget. Judged by its moment alone the arch would carry 218.

An air arch pays for its thrust out of its pressure

An inflated tube bent into an arch was expected to start with its inside wall pulled differently from its outside, and to wrinkle where that difference and the load's moment combined worst. It does not: a curved tube is pulled along its length at exactly the straight tube's pr/2, all the way round. What the arch spends its pressure on instead is the thing every arch exists to make — its own thrust — which takes a fifth of the wrinkling budget at the haunch of a shelter arch under snow and more than half on a tight one.

applied · Membrane One surplus, three depths, one slope. A 300 mm width of three cloths under 5 newtons per metre, each shortened by 1.0%, drawn at one scale in both directions. a chiffon has wrinkles 43 mm apart and 1.4 mm deep; a shirting has wrinkles 127 mm apart and 4.1 mm deep; a coating has wrinkles 249 mm apart and 8.0 mm deep. All three leave the plane at the same steepest slope, 11.5°, because that slope is set by the surplus alone.

A stiff cloth's wrinkle is deeper and no steeper

Stiffness sets how far apart a wrinkle's crests lie, and the surplus length it has to hide sets the rest. Scale a wrinkle up and its slopes do not change, so one per cent of surplus leaves a chiffon, a shirting and a coating all at 11.5 degrees, 1.4 to 8 millimetres deep. The steepness has no cloth in it — and steepness is what a light reads.

mechanics · Buckling

Named alongside it

The objects these essays reach for when they reach for this one.

Torsional rigidityTwistTwist factorStiffness ratioWrinkleBending lengthBending rigidityCrimpFlexural rigidityMeasurementBeamCantilever

All concepts