Textile Structure
how cloth is put together
Concept

Cover — where it appears

The fraction of a cloth's area its threads occupy, which decides how much light, air and water get through it. It is a ratio of a diameter to a spacing, so anything that changes the diameter and not the spacing moves every cover on a cloth at once.

Named by 26 essays across 7 fields — each of them below, with the objects they name alongside it.

The same thread, on the loom and off it. One warp end in section over eight picks, drawn twice at the same scale. The thread is the same length in both panels; in the lower one more of that length is in the bends, so the cloth it spans is shorter. Nothing has been lost — the length has moved into the crimp. The thread's thickness and the height of its bends are drawn larger than scale so the interlacing is legible; the two panels' spacings are not.

What comes off the loom is not the cloth

Every number on this site so far describes a fabric in one particular condition — held under tension, stretched to the reed width, never wetted — and none of them says so. That condition lasts until the cloth is taken off the machine, which is the first thing that happens to it.

finishing · State A fabric to fill and a fabric to load. Fill time against the sett of a woven reinforcement, with the two limits a part imposes. Stiffness wants fibre, which wants a close sett; the resin has to arrive before it gels, and the channels between the tows — which is what carries the flow — close as the sett rises. The interval between the two is where a fabric can exist, and it narrows with the size of the part.

A fabric to fill and a fabric to load

A reinforcement has to hold as much fibre as possible and still let a resin through it, and the two demands are the same decision pulling opposite ways. Both bounds are computable, the interval between them narrows as the square of the part, and past a certain size it is empty — which is the most useful thing the arithmetic says.

applied · Preform How far the bias goes, and where it stops. Extension along the bias against shear angle, with the angle at which the threads jam marked for three settings. The curve is geometry and so is the wall — a more closely set cloth reaches it sooner.

The locking angle

The bias runs out at an angle that yarn diameter and thread spacing decide between them. It is the number behind whether a cloth will go round a curve, and it has nothing to do with how strong the fabric is.

mechanics · Bias Two sections, one yarn. The same yarn given a circular cross-section and a racetrack one of equal area, both jammed. The spacing the two models allow is nearly the same; the cover and the cloth thickness they predict are not.

A tow is not a yarn

Every geometric model on this site assumes a thread with a diameter. A reinforcement tow has a width and a thickness instead, and the two are eight to one — which moves the jammed sett, the crimp, the cover and the cloth's thickness at once, in four different directions, from one change.

applied · Sett What an interlacing costs. Each weave's interlacing count beside the closest it can be set in the same yarn. The two run opposite ways, because a thread that changes face often has to bend often and a bend takes room.

How close can threads be set

There is a maximum. Push more threads into a cloth than the geometry allows and they simply will not go, and the limit depends on the weave as much as on the yarn.

setting · Sett The hole between four threads. Three millimetres of a woven filter cloth in plan, with one clear opening dimensioned and a grain of the soil it must retain drawn at the same scale. Every hole in the repeat is this size — a woven cloth's pore distribution is a single value, which is why it is specified by an opening size while a nonwoven needs a curve.

The hole between four threads

A woven cloth's holes are all the same size. That is not an approximation — it is what a repeat means — and it is the whole reason a woven filter is specified by one number while a nonwoven needs a curve. The number is the spacing less the diameter, which this site has been computing since its first questions about setting.

applied · Cover A filter cloth has two jobs. Opening size against sett for a woven filter cloth, with the two limits that specify one: the soil is retained below the retention line, and the water passes above the open-area floor. They pull opposite ways, so the answer is an interval in the sett — and for a fine enough soil there is no interval at all.

A filter cloth has two jobs

Hold the soil back and pass the water. The first wants a close sett and the second wants an open one, so a filter cloth is not a fabric but an interval — one that is sometimes a single sett wide, and for a fine enough soil is empty. The empty case is the useful one, because it says the answer is not a woven cloth at all.

applied · Openings Balanced, and not. Three weaves in section along one warp end, with the share of the face each thread system takes. The share is the mean of the matrix; what follows from it — which system wears, which carries the colour — does not follow from the matrix at all.

Balance, and what an unbalanced cloth does

How much of the surface each thread system takes is the mean of the weave matrix, and it is one of the very few quantities in this subject that can be read straight off. Almost nothing that follows from it can.

setting · Cover The same thread, on the loom and off it. One warp end in section over eight picks, drawn twice at the same scale. The thread is the same length in both panels; in the lower one more of that length is in the bends, so the cloth it spans is shorter. Nothing has been lost — the length has moved into the crimp. The thread's thickness and the height of its bends are drawn larger than scale so the interlacing is legible; the two panels' spacings are not.

The cloth gains weight by losing size

Mass per unit area is the number a fabric is bought by, and it rises by eleven per cent when a cloth relaxes — with nothing added, nothing removed and no thread changed. The quantity is a ratio, and finishing moves its denominator.

finishing · State Which dentings leave a mark. Every combination of ends per dent and weave repeat, with how many ends the grouping takes to come back into step. A small number means the reed treats every repeat the same way and the grouping shows as a stripe at the dent pitch; a large one means the grouping walks across the weave and there is nothing periodic for the eye to find. The rule is one word: dent so the two share no factor.

The reed leaves its own mark

A reed does not space a warp evenly. It groups it, several ends to a dent, and the grouping beats against the weave repeat — so a denting that shares a factor with the repeat treats every repeat identically and shows as a stripe, and one that does not is invisible.

pattern · Moire Where the twenty-eight comes from. The setting a cotton cover factor of 28 prescribes, and the setting at which the threads would cover the surface geometrically, against yarn count. They are one curve: the trade's scale is Peirce's diameter with the units taken out. Below them is the sett at which each weave actually jams, which is a fixed fraction of it.

Where the cover factor comes from

A cotton cover factor is threads per inch over the root of the count, and the scale says twenty-eight means a covered surface. The twenty-eight is not a convention: it is the reciprocal of Peirce's yarn diameter, and the trade's practical ceilings of fourteen and twenty-two fall straight out of it.

setting · Cover Everywhere a sheeting can go. Every state a sheeting of 28 × 26 threads per centimetre in 25 and 25 tex can reach without a yarn changing length, solved from Peirce's plain-weave geometry. The set is a curve and not a region: 4.03 per cent of extension is available along the warp, and reaching it costs 6.98 per cent of the width.

A cloth extends by moving its crimp

Everybody says the extension available along the warp is the warp's own crimp. On six of eight ordinary cloths it is not — a close sheeting has 14.61 per cent of warp crimp and reaches 4.03 per cent, because the limit lives in the weft.

mechanics · Tensile The same yarn, flattened. One yarn's cross-section at five degrees of flattening, all drawn at one scale and all of the same area. Nothing is added: the yarn is wider because it is thinner. The cover rises for that reason alone, which is why a calendered cloth is more opaque than the cloth that went into the machine.

Calendering is the cloth arriving at the other model

This site has carried two thread sections side by side since its foundation — Peirce's circle and Kemp's racetrack — and has been careful to say which produced any number. They are not two opinions about one yarn. They are one yarn on either side of a finishing machine.

finishing · Lustre finish Swelling, at the same count. The same yarn before and after mercerisation, drawn to one scale. Its linear density has not changed — the same grams per kilometre go into the cloth — but the fibre occupies more volume, which is a lower packing factor and a larger diameter. Every consequence in this field follows from that single number.

Mercerising is a packing factor

Cotton held in caustic soda swells, and everything the treatment is famous for follows from one number in this site's diameter calculation. The lustre it is actually sold for does not, and saying which consequences are computed and which are not is the whole of the discipline here.

finishing · Lustre finish What holds a pick in. The holding force on one weft, as a multiple of the tension applied to its free end. For a plain weave it is the capstan on twice the weave angle, which Peirce's geometry gives at each sett and which falls towards nothing as the cloth opens out. For a leno it is the capstan on a half-turn, which the sett does not enter at all.

What holds a pick in

A plain weave grips its weft by the crimp, and the crimp's wrap angle falls towards nothing as the cloth opens out. A leno crossing is half a turn whatever the sett. So the comparison has an exact answer that does not depend on the friction coefficient at all — and no plain weave can ever reach a leno's grip.

fancy · Leno The sett moves the flux and not the height. A 20 tex cotton yarn woven at every sett from 8 to 34 threads per centimetre. Above: the hole between the threads lifts from 27 to 234 mm as the cloth closes, while the space between the fibres lifts 6.37 m at every one of them — so the cloth's maximum is the flat line, and the sett does not touch it. Below: the permeability of those holes falls by a factor of 292 over the same range. Both curves are monotone, so there is no optimum — only an interval, ending at the jam at 34.6 threads per centimetre.

The sett decides how much, not how high

Every rung of this ladder so far has found the sett deciding something. This one finds it deciding nothing at all: a cloth's maximum rise is 6.37 m at eight threads per centimetre and 6.37 m at thirty-four, because the sett cannot reach inside a yarn.

setting · Sett How much a cloth can give back. Relaxation shrinkage against how much of the warp crimp the loom took out, with the area shrinkage above it and the ceiling drawn across. The ceiling is the crimp itself, read as c/(1+c): it is all the length there is to give, and no tension reaches past it.

A dimension without a state

Every essay in this field turned on the same omission, and collecting them produces a result none of them had on its own — the quantities a cloth's geometry determines divide cleanly into those a finishing works can move and those it cannot, and the division is not the one the vocabulary suggests.

finishing · State Mock leno, 3 threads to a bundle. Threads that interlace identically have no weft passing between them, so nothing holds them apart and they lie touching. The reed still sets the average spacing, so the space they leave collects at the bundle's edge — a hole 0.60 by 0.60 mm, made without one thread crossing another. Drawn to scale on a fixed 9 mm square of cloth at 20 threads per centimetre and a 0.3 mm yarn.

A hole with nothing crossing

A real leno holds its holes open by crossing one thread over another, which is a topological arrangement and cannot come undone. A mock leno makes the same holes by grouping threads that nothing separates, and everything about it is friction.

weaves · Texture weaves A coating over the hole it has to bridge. Four warp ends of 40 tex seen end-on at 20 per centimetre, with a 120 micrometre PVC film over them. The film is supported everywhere it lies on a thread and unsupported over the 252 micrometre clear span between them, which is the same span at every hole in the repeat. The film's thickness is drawn to scale against that span; the bulge is exaggerated. At 20 MPa the film will hold at most 381 bar, which is a bound and not a prediction.

A coated cloth fails at its holes

Spread a film over a fabric and it is supported everywhere it lies on a thread and unsupported over every hole. A woven cloth's holes are all the same size — exactly, because a repeat is a repeat — so the film has one span to bridge and the fabric has a burst pressure rather than a distribution. A nonwoven gives it a distribution, and a membrane fails at the largest hole it meets.

applied · Coating Selectable against reachable. How far up the take-up gear's catalogue a beat-up force reaches, on a sheeting. The catalogue holds 4,825 distinct pick densities between 8 and 40 per centimetre, which is the previous rung's count of what the machine can select. At 200 N per metre only 548 of them can be woven; at 2,000 it is 4,256. The fineness of the choice is untouched by the ceiling and the top of the range is cut off entirely, so the weft direction's advantage is resolution rather than reach. What the chart cannot show is the loom's own force, which depends on the beat-up mechanism and is not a property of the cloth.

A pick density is a force budget

The take-up ladder counted what a change-wheel take-up can select: 4,825 distinct pick densities between eight and forty threads per centimetre, against forty-nine warp setts a reed catalogue offers over the same range. That count assumed every setting is available. A beat-up force says otherwise, and cuts the top off the range without touching the fineness of the choice.

setting · Beat-up Which seams slip and which break. For each cloth, the grip a 10 mm seam allowance offers divided by the thread's own breaking load. Above one the fabric or the thread gives first and the seam holds until it does; below one the threads slide out and the seam opens with the cloth intact. voile, batiste, poplin, sheeting break; cheesecloth, muslin, duck, filter slip. The allowance that would save every cloth in the table is 74 mm, which is set by the openest of them alone. What the chart cannot show is the stitching itself, which has its own strength and its own way of cutting the threads it passes through.

A seam slips before it breaks

A sewn seam fails in one of two ways and the trade names them separately: the threads pull out of the cloth beside the stitching, or something breaks. Which one a given cloth does is decided by whether its seam allowance clears the length at which grip beats strength — and at the ordinary ten millimetres, the table divides four against four.

applied · Seams A woven cloth asked the same question, and the answer is nearly one. The closest approach two crossing threads make, for four cloths from an open voile to a dense duck, in units of the separation they have where they touch. A value of one means the closest approach is exactly at the crossing and the cloth fits together; anything below one is an overlap. The values run from 1.000 to 0.955, so the worst overlap in the table is 4.5% of a contact separation — against 22% for a knitted fabric. The overlap rises with the crimp, which is what identifies the mechanism: the vertical gain from moving away from a crossing is the crimp, and a cloth that barely crimps has nothing to gain by moving.

A woven cloth asked the same question

A knitted fabric's two adjacent courses occupy the same space by a fifth of a diameter. A woven cloth's two systems overlap by nothing at all in an open cloth and by four and a half per cent in a dense one — and the difference is that they cross rather than run alongside.

weaves · Contact What a group of 2 threads behaves as. A group of 2 threads of 250 µm with nothing separating them, beside the single thread of the same width and the single thread of the same yarn, all drawn to one scale. The bars are the group's four readings as ratios. Cover is a width and adds, so the group covers exactly what a 500 µm thread would — with 50 per cent of its yarn. Bending rigidity is a second moment and does not add: 2 threads free to slide give 12.5 per cent of the thick thread's and the same 2 fused into one body give 62.5, so a real group is somewhere between and where depends on friction. Against the thread of the same yarn the two readings point opposite ways: the group covers 1.41 times as much and bends 0.50 times as stiffly if free. What the drawing cannot show is the friction that decides where between the two limits a finished cloth sits.

A group is one thread for cover and two for bending

The rung below leaves a limitation standing: two ends with nothing between them lie touching, and whether they behave as one thread of twice the diameter was said to depend on twist, hairiness and finish. Three of the four measures have exact answers with no friction in them and no two agree. A pair covers exactly what a double-diameter thread covers, with half its yarn, and bends at between an eighth and five eighths of its rigidity — and at equal yarn it covers forty per cent more and bends half as stiffly.

weaves · Rib weaves How much of a yarn has to hang before it stops snarling. The tension a 20 tex cotton needs to stay straight, at each twist level, expressed as the length of the yarn's own weight that would supply it. The two curves are the two ends of the stiffness bracket: the fibres free to slide, and the section coherent. At 800 turns a metre they are 1.9 metres and 616. Anybody who has let go of a twisted yarn knows which of those is right, which makes this one of very few places where the bracket can be closed from the everyday end. Both rise as the square of the twist, because the torque does and the criterion is quadratic in it.

What a high-twist yarn costs a cloth

Twist buys strength up to a point and then loses it, and everything else it does is a cost. A crepe twist is chosen knowing that, and the trade's twist limits are a balance among five quantities that this collection can now put beside one another.

setting · Twist The section the fabric asks for, beside the one the model drew. A 20 tex cotton yarn in cross-section, at 900 times life size. The circle is what every solve in this collection has assumed: a diameter of 0.167 mm from the count and the packing factor. The ellipse has the same area and a minor axis of 78% of it, which is the closest the fabric's own adjacent courses come to one another — 0.130 mm. Nothing about that number was fitted to a fabric. It falls out of a solve that knew nothing about flattening, and it lands inside the range the trade reports for yarn in cloth, which this collection has carried as a free parameter ever since it first put a number on a sett.

What a flattened yarn does to its cover

A cover factor is a sett times a diameter, and it decides how much of a cloth is thread and how much is hole. A flattened yarn is a third wider than a round one of the same area, so a cloth of flattened yarn covers more at the same sett — and every opacity, permeability and shade computed from a round diameter is wrong in one direction.

setting · Cover The flattening a knitted fabric asks for, against its own tightness. Every point is a solved fabric — 18 of them, over five loop lengths, three relaxation states and three counts — and the vertical axis is the closest its adjacent courses come, in diameters. The values run from 0.707 to 0.839 and they fall on one curve against the tightness factor, which is the model's only dimensionless group. That is what makes this a structural requirement rather than an arithmetical accident of one example: a tighter fabric demands a flatter yarn, by an amount its own tightness decides, and nothing about the fibre or the count enters except through that group.

The count that decides how flat

A knitted fabric's demanded flattening is a function of its tightness factor, and a tightness factor is the square root of a count over a loop length. So a coarser yarn at the same loop is flatter — which is a prediction about a spinner's choice that nobody has framed as one.

setting · Count

Named alongside it

The objects these essays reach for when they reach for this one.

SettJammingSpecificationYarn diameterPeirce's geometryCrimpFrictionContactCover factorLoom stateNonwovenOpening size

All concepts