Yarn diameter — where it appears
Named by 52 essays across 8 fields — each of them below, with the objects they name alongside it.
A tow is not a yarn
Every geometric model on this site assumes a thread with a diameter. A reinforcement tow has a width and a thickness instead, and the two are eight to one — which moves the jammed sett, the crimp, the cover and the cloth's thickness at once, in four different directions, from one change.
The yarn count systems, and why there are several
Half the ways of saying how fine a yarn is get bigger as it gets finer and half get smaller. That is not carelessness — and one of the constants buried in the oldest rule of thumb turns out to be a measurement nobody wrote down.
The weave decides the sett, and two models disagree about it
Ashenhurst's rule and Peirce's geometry both answer how densely a cloth can be set, and for a plain weave they are fifteen per cent apart. Only one of them reaches the other weaves at all, and it is the cruder one.
Calendering is the cloth arriving at the other model
This site has carried two thread sections side by side since its foundation — Peirce's circle and Kemp's racetrack — and has been careful to say which produced any number. They are not two opinions about one yarn. They are one yarn on either side of a finishing machine.
Twist is one angle
Every model on this site treats a yarn as a cylinder with a diameter. It is a bundle of loose fibres, and what makes it behave like a cylinder is twist — which is a helix, so the whole subject is one angle, and the trade's twist factor turns out to be the only combination of count and turns that decides anything.
Mercerising is a packing factor
Cotton held in caustic soda swells, and everything the treatment is famous for follows from one number in this site's diameter calculation. The lustre it is actually sold for does not, and saying which consequences are computed and which are not is the whole of the discipline here.
A yarn's stiffness is a bracket, not a number
Two calculations are available for how stiff a thread is in bending, and both are exact. One treats the fibres as free to slide and gives the sum of their stiffnesses; the other treats them as locked and gives a solid rod. They differ by the fibre count, which for an ordinary cotton yarn is a factor of five hundred — and no measurement of the fibre narrows it by anything at all.
A yarn's voids are not enough
A ring-spun cotton yarn is sixty per cent fibre and forty per cent air, and its fibres gain forty-four per cent of area in water. The obvious thought is that the air takes it. The arithmetic says the air cannot, and gives a floor on how far the yarn itself must grow with no measurement of a yarn in it anywhere.
A cloth gives back less than it took
Everything this collection computes about a deforming fabric is reversible, and no fabric is. The repair is not a new material property: a woven cloth has two routes to a strain, one of them costs its threads nothing and comes back in full, and where the first route runs out is a number about the sett with no fibre in it at all.
The crimp ratio is not a measurement
Peirce's geometry is two thread systems, four unknowns and three equations. It cannot say how the crimp divides between warp and weft, so every cloth solved so far has been drawn at a ratio somebody chose. Give the threads a stiffness and the missing equation arrives — and for six of the eight cloths in the table it arrives with no material constant in it at all.
A flattened thread is a record of a force
A yarn in cloth is not round, and this site has modelled the flattening for as long as this collection has run with the amount of it left as a number somebody chose. Give the section a stiffness and ask what the cloth prefers, and the answer is a circle — at every stiffness, for every balanced cloth in the table. Flattening does not happen by itself; it happens because something pressed.
A hole is a channel, not an opening
Every hole drawn so far has been drawn from above, and the sentence underneath every one of them says the same thing: the hole between four threads is the spacing less the diameter, and every hole is the same size. That is a picture of a cloth's shadow. A cloth has a thickness, so its hole has a length, and the narrowest place along it is not the place a person looking through can see.
A cloth is a population, not a thread
Every number in this collection was computed from a diameter, and no yarn has one. Putting the distribution back changes some answers by nothing at all, some by a few per cent, and some by a factor — and which of the three happens is decided by one derivative.
Peirce and Kemp are one cloth at two moments
This site has run two thread sections side by side since the setting field was built — a circle and a flattened racetrack — and said honestly that they disagree and that the disagreement is the point. They are not rival descriptions of the same fabric. They are descriptions of the same fabric before and after something pressed it, and the difference between them is a pressure that can now be named.
The stiffness with no lower bound
A yarn's bending rigidity lies between two derivable ends and the ratio is the fibre count — wide, but closed. Its resistance to being squashed out of round has an upper bound of the same kind and a lower bound of exactly nothing, because fibres free to slide resist a change of shape with nothing at all. That is why nobody could ever compute the aspect ratio of a flattened thread.
Opacity is not cover
The covering rule counts a thread as a bar that stops everything, and a single fine cotton thread held to a window plainly does not. What a cloth transmits is the open area plus whatever comes through the threads, so the covered fraction is a lever rather than a barrier — and the lever is longest exactly where the rule says the cloth is most closed. Nothing here computes a thread's transmittance, and saying why is the useful half.
The cloth that was called impossible
This site's own table of fabrics carries a note saying a real 44-end poplin has no solution in its geometry at all, and that the poplin row was therefore set at 32 ends. The cloth solves. What had no solution was the search — a bisection that treated a state it could not reach as evidence of having gone too far, and walked away from the answer every time.
The hairs are what touch
The pressure inside a twisted yarn falls to exactly zero at its surface, so the outermost fibres are held by nothing and some of them stand off. A yarn therefore has two diameters — the one its mass gives and the one a neighbour meets — and only the first is in the arithmetic.
A crease is a fold the crimp cannot supply
A fold needs its outer face longer than its inner, and a woven cloth's way of supplying a length is to move crimp. That runs out at a radius of millimetres, and a pressed crease is tenths of one — so the fold is handed to the fibres. How hard it strains them turns on a question this collection has been unable to settle for two fields, and a crease settles it by refusing.
Recovery is measured and nothing predicts it
A fibre's stiffness is a bracket this collection can compute the ends of. What fraction of a strain it gives back is not: it has to be looked up, the tables are thin, they stop exactly where a fabric needs them, and the most attractive explanation for the ordering they show turns out to have no signal in it at all.
Which fibres crease, and why there are two answers
Run the sharpest fold a yarn can make against every fibre's breaking extension and its recovery, and the ranking that falls out is the trade's own — linen worst, cotton next, wool and the melt-spun filaments best. It falls out of two columns rather than one, because two fibres in the bottom three get there by different mechanisms, and a treatment that fixes one does nothing for the other.
One minus the cover is a cloth with no thickness
The covering rule says a cloth's openness is one minus its cover factor, and this collection derived it and has used it ever since. It is the answer for a light directly behind the cloth. Move the light and a line of sight has to clear the hole at the top of the fabric and the same hole one thickness below, so the openness falls, and it reaches nothing at thirty-six degrees. Averaged over the whole sky a muslin is a seventh as open as the rule says.
A loop is nine tenths free run
Half the yarn in a knitted stitch is slack — the straight line between two interlacings is a little over half the thread available to span it. That is two orders of magnitude more room than a woven thread has, and it is why a knitted loop is a shape that can be solved rather than a shape that has to be constructed.
A warp jams where its threads are thickest
The closest a cloth can be set is decided by its worst pair of neighbours, not its average thread — and the worst pair depends on how many pairs there are. The same yarn in a wider loom jams sooner, which makes a jammed sett a property of the machine as well as of the yarn.
Singeing is the cheapest change to a surface
Pass a cloth through a flame fast enough and it loses under one per cent of its mass. What it loses is the part of itself that was doing most of the touching, and lustre, friction, printability, pilling and measured cover all move at once.
A yarn has a diameter for every instrument
Conservation of volume gives a yarn one diameter and every other route gives a different one. The disagreement is not experimental scatter: a yarn's outside is a coverage that falls away exponentially, and each instrument stops at whatever contour of it will trigger the instrument.
How many fibres make a thread
Every number in this collection began with a diameter, and a diameter is not a measurement — it is a count of fibres, divided. Once the division is written down, three quantities that had nothing to do with each other turn out to be the same number.
How far a knit could go if its yarn were the limit
The yarn in a stitch allows three hundred and twenty per cent course-wise extension before the straight line between two interlacings reaches the thread spanning it. A jersey jams at about a hundred. The factor of three is the finding: what stops a knit stretching is not the loop running out of yarn.
Folding is untwisting
Wind two singles round each other and each one turns about its own axis once per turn of the fold. So a folded yarn's singles are not the singles that went into it, and at a folding ratio of exactly one half the two helices cancel.
The diameter was quoted at one twist
Every diameter in this collection came from a packing factor of 0.6, and that number was got by inverting a rule published for cotton yarns at one particular twist. Here is what moves if it is wrong by the width of the range real yarns occupy — and which single quantity does not move at all.
Two knits with one tightness factor are one knit
The loop model has exactly one dimensionless group in it — the yarn's diameter over the loop length — so two fabrics that share it have the same loop, to fifteen figures, whatever they are made of. That group is the knitter's own tightness factor, and it explains why an index quoted as empirical works as well as it does.
The closest approach is not the crossing
Two wavy curves that touch at a point are not necessarily closest at that point. Whether they are depends on one thing: whether they run alongside one another or cross. That distinction decides which of this collection's two fabrics fits together and which does not.
Where a yarn is thinnest
A yarn in a fabric is pressed where it crosses and free where it does not, so its section changes along its own length. Every flattening this collection has ever quoted is a single number for a profile that runs from four fifths of a diameter to nearly four.
A woven cloth asked the same question
A knitted fabric's two adjacent courses occupy the same space by a fifth of a diameter. A woven cloth's two systems overlap by nothing at all in an open cloth and by four and a half per cent in a dense one — and the difference is that they cross rather than run alongside.
A group is one thread for cover and two for bending
The rung below leaves a limitation standing: two ends with nothing between them lie touching, and whether they behave as one thread of twice the diameter was said to depend on twist, hairiness and finish. Three of the four measures have exact answers with no friction in them and no two agree. A pair covers exactly what a double-diameter thread covers, with half its yarn, and bends at between an eighth and five eighths of its rigidity — and at equal yarn it covers forty per cent more and bends half as stiffly.
A cord's height has a ceiling and its width has none
A warp rib's cord is a wave, and its two dimensions come from two different places. The height is the weft's own crimp amplitude, and Peirce's closure condition caps it at the two yarn diameters together — 500 µm for a quarter-millimetre yarn, of which a 2/2 rib reaches 304 and a 6/6 rib 391. The pitch is the doubling times the pick spacing and has no cap at all. So a bolder rib is taller and wider, and wider faster: the aspect falls from 0.41 to 0.22.
The fabric that does not fit
Every solve in this collection minimises an energy over a centre line, and a centre line has no thickness. Nobody had checked whether the fabric that comes out of it can be built. It cannot: two adjacent courses of the relaxed jersey approach to four fifths of a yarn diameter, so the yarn passes through itself, at rest, everywhere.
The flattening nobody fitted
A yarn in cloth is not round, everybody knows it, and nothing has ever predicted how flat. This collection's own knitted geometry turns out to require a flattening of four fifths — from a solve that knew nothing about flattening, made no allowance for it, and would have been written the same way if the idea had never occurred to anybody.
A wet knit's yarn is flatter
A knitted fabric's own geometry demands a flattened yarn, and how flat depends on how much room the fabric leaves. A wet cotton yarn is a tenth thicker than a dry one at the same length, so a wet fabric leaves less room — and asks its yarn to be flatter by an amount the geometry gives.
A flattening that follows the tightness factor
Eighteen solved fabrics — five loop lengths, three relaxation states, three counts — and the flattening each one's geometry demands falls on a single curve against one dimensionless group. Nothing about the fibre or the count survives except through that group, which is what turns an arithmetical result into a structural requirement.
What wetting does to the bending limit
A rod cannot be bent to a radius below its own. A relaxed knitted loop sits at twice that limit, and a wet yarn is a tenth thicker in the same loop — so wetting moves a fabric a tenth of the way towards a bend it cannot physically take.
The folding rule is a surface angle
Fold at two thirds for two singles, six tenths for three, a half for four. Those are one over the square root of the fold count, they are what makes a fold's surface twist angle equal its singles', and all three of the trade's brackets contain the number exactly.
A loop bends at twice its own radius
A rod of radius r cannot be bent to a centre-line radius below r without occupying its own space. A knitted loop's tightest bend is at 2.04 yarn radii — twice the hard limit, and falling as the fabric tightens. That is a ceiling on how tight a knit can be, from contact alone.
The diameter that does need a state
A fabric dimension quoted without its relaxation state is not a measurement. The rule was applied to the two plan dimensions and then to the thickness, and it was never applied to the one dimension that is not the fabric's at all — the yarn's.
Contact is not why a jersey stops
The model says a jersey can be pulled to three hundred and twenty per cent along its courses. Real ones stop at about a hundred. The recorded diagnosis was that nothing stops adjacent courses passing through one another — and giving the yarn a thickness closes seven per cent of a gap of two thirds.
A cabled yarn is a fold of folds
The rule that sets a fold's twist is one over the square root of the number of components. Apply it twice and a cabled yarn's three twist levels are fixed by two integers — which is a prediction with no free constants, about a class of yarn the trade quotes no rule for at all.
What holds a crest apart
Two half periods meet at every crest of every course and, in this collection's model, run within a fiftieth of a yarn diameter of one another for more than a millimetre. In a fabric what holds them apart is the loop of the next course drawn between them — which is the loop this model does not have.
What a sett is when the yarn is not round
A jamming condition says how close threads can be set, and it says it in terms of a diameter. A thread in a cloth does not have one diameter: it has a wide one and a narrow one, and which of them a jam is about depends on which way the threads are jamming.
What a flattened yarn does to its cover
A cover factor is a sett times a diameter, and it decides how much of a cloth is thread and how much is hole. A flattened yarn is a third wider than a round one of the same area, so a cloth of flattened yarn covers more at the same sett — and every opacity, permeability and shade computed from a round diameter is wrong in one direction.
The count that decides how flat
A knitted fabric's demanded flattening is a function of its tightness factor, and a tightness factor is the square root of a count over a loop length. So a coarser yarn at the same loop is flatter — which is a prediction about a spinner's choice that nobody has framed as one.
Flattening is free and impossible
The fabric demands a flattening and the yarn has to supply it. At one end of this collection's oldest bracket the deformation costs exactly nothing; at the other it costs thirty-six times the whole bending energy of a stitch. The fabric flattens — which is the fourth everyday observation in one phase to land at the same end.
The section that changes both stiffnesses
A thread's two rigidities are in the ratio 2G/E, and that is a fact about a circular section: a circle's polar second moment is exactly twice its flexural one. A yarn in cloth is not circular, so a yarn in cloth has three constants rather than two — and the ratio a whole ladder rests on is a lower bound.
Named alongside it
The objects these essays reach for when they reach for this one.
Packing factorJammingContactSettBending rigidityCover factorSpecificationCloth thicknessLoopLoop lengthPeirce's geometryTightness factor