Sett — where it appears
Named by 67 essays across 8 fields — each of them below, with the objects they name alongside it.
Thread count is not quality
It counts threads. It says nothing about how much of the cloth they cover, it can be inflated by counting plies, and it ranks fabrics in nearly the wrong order. The quantity it is mistaken for is cover factor, and that one is computable.
What comes off the loom is not the cloth
Every number on this site so far describes a fabric in one particular condition — held under tension, stretched to the reed width, never wetted — and none of them says so. That condition lasts until the cloth is taken off the machine, which is the first thing that happens to it.
A tow is not a yarn
Every geometric model on this site assumes a thread with a diameter. A reinforcement tow has a width and a thickness instead, and the two are eight to one — which moves the jammed sett, the crimp, the cover and the cloth's thickness at once, in four different directions, from one change.
How close can threads be set
There is a maximum. Push more threads into a cloth than the geometry allows and they simply will not go, and the limit depends on the weave as much as on the yarn.
A cloth cannot shrink past its own crimp
However hard a loom held the warp, there is a limit to what relaxation can take back, and it is not a fitted constant or a measured one. It is the crimp itself, read as c over one plus c, and it is the only result in this field with nothing empirical in it at all.
Interlacings and firmness
Every time a thread changes face it has to bend, and a bend takes room. That one sentence decides how densely a cloth can be set, how firm it feels, and why the two run in opposite directions.
The hole between four threads
A woven cloth's holes are all the same size. That is not an approximation — it is what a repeat means — and it is the whole reason a woven filter is specified by one number while a nonwoven needs a curve. The number is the spacing less the diameter, which this site has been computing since its first questions about setting.
A filter cloth has two jobs
Hold the soil back and pass the water. The first wants a close sett and the second wants an open one, so a filter cloth is not a fabric but an interval — one that is sometimes a single sett wide, and for a fine enough soil is empty. The empty case is the useful one, because it says the answer is not a woven cloth at all.
The cloth gains weight by losing size
Mass per unit area is the number a fabric is bought by, and it rises by eleven per cent when a cloth relaxes — with nothing added, nothing removed and no thread changed. The quantity is a ratio, and finishing moves its denominator.
The weave decides the sett, and two models disagree about it
Ashenhurst's rule and Peirce's geometry both answer how densely a cloth can be set, and for a plain weave they are fifteen per cent apart. Only one of them reaches the other weaves at all, and it is the cruder one.
Corduroy is a cut float
An extra weft floats over some ends, a knife runs along the cloth, and each half of the float stands up. So the pile height is exactly half the float's length — which makes corduroy the one pile fabric whose surface is decided entirely by a quantity this site has been counting since its first essay.
The reed leaves its own mark
A reed does not space a warp evenly. It groups it, several ends to a dent, and the grouping beats against the weave repeat — so a denting that shares a factor with the repeat treats every repeat identically and shows as a stripe, and one that does not is invisible.
Where the cover factor comes from
A cotton cover factor is threads per inch over the root of the count, and the scale says twenty-eight means a covered surface. The twenty-eight is not a convention: it is the reciprocal of Peirce's yarn diameter, and the trade's practical ceilings of fourteen and twenty-two fall straight out of it.
Why satin shines
Lustre is usually filed under fibre, and silk gets the credit. It is a property of the weave: a cylinder reflects a line rather than a point, so the highlight a cloth returns is exactly as long as its longest float.
A cloth extends by moving its crimp
Everybody says the extension available along the warp is the warp's own crimp. On six of eight ordinary cloths it is not — a close sheeting has 14.61 per cent of warp crimp and reaches 4.03 per cent, because the limit lives in the weft.
What crimp interchange actually conserves
Pull a cloth lengthways and it narrows, because the crimp moves from one system to the other. Inextensibility says that much and no more — it is one equation short of an answer, and the second equation everybody uses is an assumption with a name.
Floats and abrasion
A satin is said to wear badly. It does not wear quickly — its flat face spreads the rubbing over more thread than a plain weave's crowns do. What it does is fail badly, and those are different quantities moving in opposite directions.
Does a loose weave tear better
The trade says a twill tears stronger than a plain weave of the same yarn, because fewer interlacings let the threads group. The geometry of that grouping has no weave in it at all — and where the geometry does speak, it predicts the opposite.
Every crossing is a force
A thread arrives at a crossing at an angle and leaves at its negative, so the two pulls have transverse parts that add. The force pressing one thread onto another is twice the tension times the sine of the weave angle — and for an ordinary sheeting that is more than the tension in the thread itself.
A thread is held one crossing at a time
Grip a thread over a length of cloth and its resistance to being pulled out rises with that length, because it is held at every crossing it makes. Its own breaking load does not rise at all. The two curves cross, and the length at which they cross turns out to be a seam allowance, a frayed edge and a tuft's anchorage — three rules of thumb with one number under them.
Twist and the twill line
The oldest rule of thumb in weaving says to weave a Z twill from S-twist warp for a bold line and from Z-twist warp for a subdued one. Both halves of it are geometry: the twill's angle comes from the two setts, the fibres' angle comes from the twist factor, and the rule is their difference.
What a fabric weighs
Every fabric is sold by its weight in grams per square metre, and the number is a sum of four products in which no term appears alone. One equation, four unknowns: a hundred and fifty grams describes an open coarse cloth and a close fine one, and the cover factors differ by a factor of nearly three.
What holds a pick in
A plain weave grips its weft by the crimp, and the crimp's wrap angle falls towards nothing as the cloth opens out. A leno crossing is half a turn whatever the sett. So the comparison has an exact answer that does not depend on the friction coefficient at all — and no plain weave can ever reach a leno's grip.
A woven outline is a staircase
A jacquard's resolution is quoted as its hook count, and on a 1,200-hook machine 140 cm wide that is a step of 1.17 mm. The cloth cannot use it. A figure's smallest feature is one repeat of the ground weave, which on an eight-end satin is 3.33 mm — so the machine resolves nearly three times finer than the fabric can hold, and a finer machine buys nothing at all.
The sett decides how much, not how high
Every rung of this ladder so far has found the sett deciding something. This one finds it deciding nothing at all: a cloth's maximum rise is 6.37 m at eight threads per centimetre and 6.37 m at thirty-four, because the sett cannot reach inside a yarn.
The stitch that weakens the seam
More stitches per centimetre put more sewing thread across a seam and more holes through the cloth beside it, so seam strength rises, crosses and falls. Whether the fabric line falls at all is decided by the clear gap between two threads against the width of the needle — the same arithmetic a filter cloth is specified by, doing a different job.
The reed is not the sett
A reed holds the warp at a pitch, and the cloth that leaves it is narrower — by exactly the weft's crimp, with nothing fitted and nothing approximated. On a close balanced sheeting that is 12.75 per cent, on an open scrim 1.87, and a weaver who allowed one figure for both would be wrong by a factor of nearly seven.
The setts a loom can reach
Transposing a draft gives a perfectly good draft, and every count this site takes off a matrix either is symmetric under exchanging warp and weft or has a mirror twin. The loom is not symmetric at all: over the range ordinary cloth is woven in, it can choose a pick density 99 times more finely than a warp sett — and the warp sett cannot be changed once the warp is drawn in, at any granularity whatever.
A cloth gives back less than it took
Everything this collection computes about a deforming fabric is reversible, and no fabric is. The repair is not a new material property: a woven cloth has two routes to a strain, one of them costs its threads nothing and comes back in full, and where the first route runs out is a number about the sett with no fibre in it at all.
A hole with nothing crossing
A real leno holds its holes open by crossing one thread over another, which is a topological arrangement and cannot come undone. A mock leno makes the same holes by grouping threads that nothing separates, and everything about it is friction.
The crimp ratio is not a measurement
Peirce's geometry is two thread systems, four unknowns and three equations. It cannot say how the crimp divides between warp and weft, so every cloth solved so far has been drawn at a ratio somebody chose. Give the threads a stiffness and the missing equation arrives — and for six of the eight cloths in the table it arrives with no material constant in it at all.
A cord is a stripe with no colour in it
Warp rib, weft rib and hopsack are plain weave with its threads doubled, in the warp, the weft, or both. Six of the nine measures this site takes off a matrix cannot tell a 2/2 hopsack from a 2/2 twill, and the three that can are not the ones a weaver quotes.
The blow that sets the pick
The take-up gear decides how far the cloth moves between picks and says nothing about the blow that puts each pick where it goes. That blow is a force, and a virtual-work argument gives it in one line — with the length of the beat-up zone cancelling out of the answer exactly, which is the part worth having.
The most a cloth can give back
The extension a cloth can find without stretching a thread comes from crimp, so setting a cloth closer ought to give it more. It does, up to a point, and then takes it away again — and the point is a cover factor of 0.4078 at a budget of 7.2857 per cent, identical to six figures for every yarn count from five tex to a hundred.
Wicking is slower along a crimped thread
A front travelling up a warp end travels the thread's path, which is longer than the cloth by exactly the crimp. So the wicking coefficient measured on the fabric is the yarn's own divided by (1 + c)² — 14.3 per cent lost at eight per cent crimp, whatever the liquid.
A coated cloth fails at its holes
Spread a film over a fabric and it is supported everywhere it lies on a thread and unsupported over every hole. A woven cloth's holes are all the same size — exactly, because a repeat is a repeat — so the film has one span to bridge and the fabric has a burst pressure rather than a distribution. A nonwoven gives it a distribution, and a membrane fails at the largest hole it meets.
A hole is a channel, not an opening
Every hole drawn so far has been drawn from above, and the sentence underneath every one of them says the same thing: the hole between four threads is the spacing less the diameter, and every hole is the same size. That is a picture of a cloth's shadow. A cloth has a thickness, so its hole has a length, and the narrowest place along it is not the place a person looking through can see.
A motif is drawn at the wrong shape on purpose
Point paper has one cell per end and per pick, so a design's proportions on the cloth are the ratio of the two setts. Both setts move in the finishing and they move in opposite directions, so a circle drawn as a circle comes back out of round — by three per cent on a balanced cloth and by sixteen on a warp-dense one.
A pick density is a force budget
The take-up ladder counted what a change-wheel take-up can select: 4,825 distinct pick densities between eight and forty threads per centimetre, against forty-nine warp setts a reed catalogue offers over the same range. That count assumed every setting is available. A beat-up force says otherwise, and cuts the top off the range without touching the fineness of the choice.
What holds a tuft in, in newtons
The pile ladder computed a tuft's anchorage as a capstan ratio and said, correctly, that a ratio was all it could offer. A ratio multiplies a tension and there was no tension anywhere on this site. There is one now — and the answer, put beside what a carpet is actually specified at, falls short by a factor of three.
A seam slips before it breaks
A sewn seam fails in one of two ways and the trade names them separately: the threads pull out of the cloth beside the stitching, or something breaks. Which one a given cloth does is decided by whether its seam allowance clears the length at which grip beats strength — and at the ordinary ten millimetres, the table divides four against four.
Peirce and Kemp are one cloth at two moments
This site has run two thread sections side by side since the setting field was built — a circle and a flattened racetrack — and said honestly that they disagree and that the disagreement is the point. They are not rival descriptions of the same fabric. They are descriptions of the same fabric before and after something pressed it, and the difference between them is a pressure that can now be named.
Two layers are the product on average and nowhere
Everybody knows what two layers of a cloth pass: the product of their open areas. That figure is exactly right — it is the mean of the true answer over every way the two layers can lie — and it is the answer at two registrations out of a continuum. In register a doubled cloth is as open as a single one; half a thread out it can be shut completely. The variation across a folded curtain is what a moiré is.
The cloth that was called impossible
This site's own table of fabrics carries a note saying a real 44-end poplin has no solution in its geometry at all, and that the poplin row was therefore set at 32 ends. The cloth solves. What had no solution was the search — a bisection that treated a state it could not reach as evidence of having gone too far, and walked away from the answer every time.
The hairs are what touch
The pressure inside a twisted yarn falls to exactly zero at its surface, so the outermost fibres are held by nothing and some of them stand off. A yarn therefore has two diameters — the one its mass gives and the one a neighbour meets — and only the first is in the arithmetic.
A leno's hole cannot drift
A filter cloth is rated by its largest hole, and the largest hole grows one micrometre for every micrometre an end moves sideways. What holds an end in place in an ordinary weave is friction at its crossings, and that friction falls smoothly to nothing as a cloth opens — with no threshold to warn anybody. A leno's crossing does not: its ends are wrapped through half a turn by construction, so the grip has no sett in it, and at an open cloth it holds eighteen times what a plain weave manages.
A wet cloth is set closer than it was woven
Cover is a diameter over a spacing. Wetting moves the diameter and does not move the spacing, so every cover factor on this site is multiplied by exactly the swelling ratio and every jamming sett divided by it — which is an identity, and the one statement in this ladder a reader can check by hand.
A filter is rated by the hole it does not show
A woven filter cloth is sold on two numbers pulling opposite ways: an opening small enough to hold the soil and an open area large enough to pass the water. Both are computed from the same holes, and they are not computed from the same statistic of them. One reads the maximum and the other reads the mean, so a change that improves either can worsen the other without moving a single measurable property of the cloth.
Wetting moves a cloth to another locus
A cloth's constant-thread-length locus is built at a fixed thickness. Swelling changes the thickness, so a wetted cloth is not somewhere else on its own locus — it is on a different one, and the distance between the two least-energy states is the shrinkage. Five of the eight cloths here have a wet state, and one of them gets bigger.
A cloth cannot be more even than its yarn
It can be very much more even than its yarn, and by exactly the square root of the threads in view. Which raises a question the fineness argument left open — and the answer is that at a fixed cloth weight the count cancels out entirely.
The construction a loom must be set to
A specification quotes ends and picks per centimetre in the finished cloth, and a loom is set to neither of them. The cloth relaxes to the least-energy state of its own locus, which is a state at a different sett — and because the locus is one curve, the two numbers a specification quotes are not two free numbers.
Only a plain weave has one size of hole
A weave's holes come in kinds, and the kinds are read off the matrix. Asking which weaves have only one kind looks like a question with an obvious answer and a one-line proof. Every draft at four by four was built and asked instead, and the count came back fourteen — of which twelve turn out to be telling the truth about the sett rather than about the weave.
The fourth power is a close cloth's rule
Every account of a fabric's air permeability quotes the same thing: flow down a channel goes as the fourth power of its width, so a small change of sett is a large change of flow. That is Poiseuille's result, it is about the viscous drop, and in an open cloth the viscous drop is two per cent of the pressure. The rule becomes true as the cloth closes, and where it starts being true is a number.
One minus the cover is a cloth with no thickness
The covering rule says a cloth's openness is one minus its cover factor, and this collection derived it and has used it ever since. It is the answer for a light directly behind the cloth. Move the light and a line of sight has to clear the hole at the top of the fabric and the same hole one thickness below, so the openness falls, and it reaches nothing at thirty-six degrees. Averaged over the whole sky a muslin is a seventh as open as the rule says.
A warp jams where its threads are thickest
The closest a cloth can be set is decided by its worst pair of neighbours, not its average thread — and the worst pair depends on how many pairs there are. The same yarn in a wider loom jams sooner, which makes a jammed sett a property of the machine as well as of the yarn.
A leno twists what a weave only crosses
Every woven cloth's threads have a linking number of zero, and that is why an open cloth slips. A leno is the one woven structure whose warp ends wind about one another, so it is the one whose threads are linked — and it is famously the structure that holds at setts where nothing else does.
Two layers need two beams
A layer weaving a metre of cloth eats one plus its crimp metres of warp, and a beam delivers one rate. A plain face over a five-end satin back differs by twelve percentage points of crimp, which is twelve metres of warp over a hundred-metre piece and one pick spacing of slack after four millimetres of weaving. The difference has nowhere to go and does not settle — so the only double cloth that can share a beam is two layers of the same weave at the same sett.
Why a knit runs and a weave frays
The two fabrics fail in two ways and everybody knows which is which. This collection has described both accurately for eighteen phases without being able to say what causes them, and the cause turns out to be one integer each: nought for a cloth, one per wale for a knit.
The sett owns the pitch and the yarn owns the height
Set a cloth twice as close and its surface does not get smoother. The crowns come twice as often, because that is what a sett is, and they stand at very nearly the same height, because the closure condition pins the amplitude to the yarn — so a fine cloth is finer-grained rather than flatter, and the two are confused in every description of handle.
A woven cloth is not linked at all
Every thread in every woven cloth passes over its neighbours and comes back. None of them passes through. So the linking number of any two threads in any weave is zero, at any crimp, permanently — and almost everything a cloth does that a knitted fabric does not follows from that one number being nought.
A woven cloth asked the same question
A knitted fabric's two adjacent courses occupy the same space by a fifth of a diameter. A woven cloth's two systems overlap by nothing at all in an open cloth and by four and a half per cent in a dense one — and the difference is that they cross rather than run alongside.
A cord's height has a ceiling and its width has none
A warp rib's cord is a wave, and its two dimensions come from two different places. The height is the weft's own crimp amplitude, and Peirce's closure condition caps it at the two yarn diameters together — 500 µm for a quarter-millimetre yarn, of which a 2/2 rib reaches 304 and a 6/6 rib 391. The pitch is the doubling times the pick spacing and has no cap at all. So a bolder rib is taller and wider, and wider faster: the aspect falls from 0.41 to 0.22.
The four named weaves are corners of a family
Plain, warp rib, weft rib and hopsack are one construction with two knobs, and the trade turns both together or neither. Group the ends by two and the picks by three and the result is an ordinary cloth with a name, no literature and a fundamental domain of twelve intersections on two shafts — and the family's three quantities all have closed forms: two shafts everywhere, a unit of exactly 2ab, and a longest float of the larger grouping.
A jacquard's harness has a depth after all
A jacquard was said to escape the shaft loom's depth entirely, because every mail hangs at the same distance from the fell. Every mail does, if the comber board has one row of holes — and it cannot. At sixty ends a centimetre the ends are a sixth of a millimetre apart and a cord with a mail on it wants most of one, so the holes are ruled in six rows thirty millimetres deep. The escape is real and it is a factor of eight rather than a release, and it closes as the cloth is set finer.
What a sett is when the yarn is not round
A jamming condition says how close threads can be set, and it says it in terms of a diameter. A thread in a cloth does not have one diameter: it has a wide one and a narrow one, and which of them a jam is about depends on which way the threads are jamming.
What a flattened yarn does to its cover
A cover factor is a sett times a diameter, and it decides how much of a cloth is thread and how much is hole. A flattened yarn is a third wider than a round one of the same area, so a cloth of flattened yarn covers more at the same sett — and every opacity, permeability and shade computed from a round diameter is wrong in one direction.
A satin's row belongs to its sett
Point paper draws an end and a pick as equal squares, and every result about which satins have a row was taken there. A cloth is not square: it is set at so many ends and so many picks a centimetre, and in cloth the ties that made twelve satin orders row-free are ties between steps of different shape, which break at the first per cent of unequal sett. The reverse happens too. An eight-end satin, rowed on paper, has no row at exactly 1.291 ends per pick; an eleven-end at 1.265 and 1.528. And the only scatter that survives a range of setts is an irregular satin whose closest steps are mirror images — which nine ends has from the first per cent and ten only by 1.3.
Named alongside it
The objects these essays reach for when they reach for this one.
JammingCrimpCover factorCoverPeirce's geometrySpecificationYarn diameterFrictionFloatInterlacingClear openingCloth integrity