Textile Structure
how cloth is put together
Concept

Seam — where it appears

A joint between two pieces of cloth, which fails either by its stitches breaking or by the fabric's own threads sliding out beside them. Which of the two ways it fails is decided by the allowance and the cloth's own grip, and the two failures want opposite remedies.

Named by 7 essays across 2 fields — each of them below, with the objects they name alongside it.

What holds a thread in a seam. A cloth thread inside a seam allowance, drawn past the crossings that grip it, with the capstan's factor at each. The tension falls by that factor at every crossing, so the grip is exponential in the crossing count and the count is what the weave decides. Beyond the thread's own strength the thread breaks rather than slides, and the rest of the allowance holds nothing.

What holds a thread in a seam

A seam fails in two quite different ways, and the one the trade worries about is not the stitches breaking. It is the cloth's own threads sliding out of the weave beside the seam — and what resists that is friction at the crossings, accumulating multiplicatively, so a satin gives a seam a thousandth of the grip a plain weave gives it.

applied · Seams The stitch density that makes the strongest seam. Seam strength against stitch density, as the two limits that decide it: the sewing thread crossing the seam, which rises with the stitches, and the fabric the needle perforates, which falls. The seam is the lower of the two, so the optimum is where they cross — and whether the fabric line falls at all is decided by the clear gap between threads against the width of the needle.

The stitch that weakens the seam

More stitches per centimetre put more sewing thread across a seam and more holes through the cloth beside it, so seam strength rises, crosses and falls. Whether the fabric line falls at all is decided by the clear gap between two threads against the width of the needle — the same arithmetic a filter cloth is specified by, doing a different job.

applied · Seams Which seams slip and which break. For each cloth, the grip a 10 mm seam allowance offers divided by the thread's own breaking load. Above one the fabric or the thread gives first and the seam holds until it does; below one the threads slide out and the seam opens with the cloth intact. voile, batiste, poplin, sheeting break; cheesecloth, muslin, duck, filter slip. The allowance that would save every cloth in the table is 74 mm, which is set by the openest of them alone. What the chart cannot show is the stitching itself, which has its own strength and its own way of cutting the threads it passes through.

A seam slips before it breaks

A sewn seam fails in one of two ways and the trade names them separately: the threads pull out of the cloth beside the stitching, or something breaks. Which one a given cloth does is decided by whether its seam allowance clears the length at which grip beats strength — and at the ordinary ten millimetres, the table divides four against four.

applied · Seams Shrinkage from wetting, cloth by cloth. The change in each cloth's relaxed construction when its threads swell by 20% across and 1.2% along. Both states are least-energy states of their own constant-thread-length locus, which is the only comparison the locus admits: its minimum is a state at its own sett, so it may be compared with another minimum and not with a quoted construction. Positive is smaller. Every cloth that has a wet state closes up except the cheesecloth, which opens by half a per cent because the fibre's extra hundredth of length outruns the extra crimp a thicker partner costs. What the bars cannot show is the three cloths that are missing, which have no wet state at all.

A garment is cut dry and worn wet

A cutting allowance is one number and the thing it allows for is two, in two directions. Worse: when the two directions differ, a panel cut on the bias does not merely shrink — it rotates, by half a degree for an ordinary poplin, which is nine and a half millimetres of skew across a metre and is invisible to a tape measure.

applied · Cutting Folding, and what it takes out of the singles. Two 20 tex singles spun at 800 turns per metre and folded the other way at 460 — a ratio of 0.575, which is the trade's own and is a measurement rather than a derivation. A single held at its ends and wound round its neighbour turns about its own axis once for every turn of the fold, so it is left with 340 turns per metre of its own: its surface fibres lie at 10.1° to its axis rather than the 22.8° they were spun at. Folding untwists. The short strokes are drawn at that residual angle; the two long curves are centre lines and are not the yarn — each strand is itself a bundle of 118 fibres, and the residual angle is what holds them.

A sewing thread is a different animal

It is folded, balanced, lubricated and finished, and every one of those is an answer to a requirement no weaving yarn has. The lubricant is the interesting one: it makes the thread sewable by lowering the friction that was holding its own fibres together.

applied · Seams A seam stands 763 µm proud of a cloth 382 µm thick. A 10 mm seam allowance of 3 plies in a 60 mm panel of one, in sheeting. The seam stands 763 µm above the body of the garment — which is 102 times the depth at which the body cloth first comes into contact with anything at all. So a flat surface rubbed across this garment touches only the seam, over 16.7% of the area drawn, until it has crushed a whole thickness of fabric. Everything this collection computes about where wear lands on a woven surface applies inside that 16.7%, and the other 83.3% is not being touched.

A seam stands proud and wears first

A seam allowance is three plies where the garment is one, so it stands three quarters of a millimetre above a cloth whose own surface has a few micrometres of contact in it. Anything flat rubbed across the garment touches the seam and nothing else — all of the wear on two or three per cent of the area, until a whole thickness of fabric has been crushed.

applied · Seams A 4-layer stack round a 180° fold. 4 layers of 260 µm cloth taken round a 180 degree fold, drawn as concentric arcs at their own separation. The outer layer runs round a larger radius than the inner one, so it must be longer — by the angle times the separation, which is 2.45 mm here and 0.82 mm at every interface. In a loose stack that length is found by the layers sliding over one another at the fold. In a stitched seam they cannot: the stitches pin them every 3 mm, so the slip a fold needs is 82 per cent of the distance between two stitches and has nowhere to come from. What the arcs cannot show is what happens instead, which is that the fold opens out to a radius the stack can manage.

A crease cannot cross a seam

The outer layer of a folded stack has further to go than the inner, by the fold's angle times the stack's own thickness. A four-layer seam of quarter-millimetre cloth taken through a half turn needs its outer layer to be 2.45 millimetres longer than its inner — and a stitch line every three millimetres has pinned them. So the fold opens out where it crosses the seam, which is what a trouser crease visibly does, and the arithmetic gives the radius it opens to.

finishing · Crease

Named alongside it

The objects these essays reach for when they reach for this one.

FrictionSeam slippageSpecificationAbrasionCloth thicknessFloatSettAllowanceAnchorageBearing curveBiasCalendering

All concepts