Textile Structure
how cloth is put together
Concept

Seam slippage — where it appears

A fabric's threads pulling out of the weave beside a seam, resisted by friction at the crossings and worst in cloths with long floats. It is a crossover-length problem, so the fray width, the seam allowance and the tuft's bound length are all one arithmetic in three dresses.

Named by 9 essays across 3 fields — each of them below, with the objects they name alongside it.

Where a thread stops sliding and starts breaking. A pick of sheeting gripped over a length of cloth, drawn one crossing at a time. The resistance is 0.30 times the 0.599 N each crossing presses with, so it rises with the length held; the breaking load of 3.74 N does not. The two are equal at 7.4 mm. What the drawing cannot show is that μ is a range rather than a constant, so the mark is a band and its position is exactly inversely proportional to the friction.

A thread is held one crossing at a time

Grip a thread over a length of cloth and its resistance to being pulled out rises with that length, because it is held at every crossing it makes. Its own breaking load does not rise at all. The two curves cross, and the length at which they cross turns out to be a seam allowance, a frayed edge and a tuft's anchorage — three rules of thumb with one number under them.

cloth · Contact A thread withdrawn from a plain weave and from a satin. One pick of a sheeting being pulled from 1.60 mm of cloth, in a plain weave and in a five-end satin, at a friction coefficient of 0.30. The drawn width of each thread is the tension in it at that point, to a common scale; the faint rules are where the thread actually turns, which is at its interlacings and nowhere else. A plain weave turns 2.80 times per millimetre and a satin 1.12, so the plain weave's tension compounds 2.78-fold over this length against the satin's 1.46. What the drawing cannot show is that the wrap angle is taken from a plain-weave geometry in both panels: a satin's crimp is genuinely smaller, so its real turns are gentler than these and its grip weaker still.

A thread is gripped where it turns

The arithmetic this site has used for fraying, seam slippage and tuft anchorage counts every crossing a thread makes as a grip and adds them up. A thread lying flat on the surface of a satin presses on nothing at all, and a thread that is gripped is gripped by a friction that compounds along its length rather than adding. Both corrections were recorded as missing and both are here.

cloth · Contact What holds a thread in a seam. A cloth thread inside a seam allowance, drawn past the crossings that grip it, with the capstan's factor at each. The tension falls by that factor at every crossing, so the grip is exponential in the crossing count and the count is what the weave decides. Beyond the thread's own strength the thread breaks rather than slides, and the rest of the allowance holds nothing.

What holds a thread in a seam

A seam fails in two quite different ways, and the one the trade worries about is not the stitches breaking. It is the cloth's own threads sliding out of the weave beside the seam — and what resists that is friction at the crossings, accumulating multiplicatively, so a satin gives a seam a thousandth of the grip a plain weave gives it.

applied · Seams The stitch density that makes the strongest seam. Seam strength against stitch density, as the two limits that decide it: the sewing thread crossing the seam, which rises with the stitches, and the fabric the needle perforates, which falls. The seam is the lower of the two, so the optimum is where they cross — and whether the fabric line falls at all is decided by the clear gap between threads against the width of the needle.

The stitch that weakens the seam

More stitches per centimetre put more sewing thread across a seam and more holes through the cloth beside it, so seam strength rises, crosses and falls. Whether the fabric line falls at all is decided by the clear gap between two threads against the width of the needle — the same arithmetic a filter cloth is specified by, doing a different job.

applied · Seams Which seams slip and which break. For each cloth, the grip a 10 mm seam allowance offers divided by the thread's own breaking load. Above one the fabric or the thread gives first and the seam holds until it does; below one the threads slide out and the seam opens with the cloth intact. voile, batiste, poplin, sheeting break; cheesecloth, muslin, duck, filter slip. The allowance that would save every cloth in the table is 74 mm, which is set by the openest of them alone. What the chart cannot show is the stitching itself, which has its own strength and its own way of cutting the threads it passes through.

A seam slips before it breaks

A sewn seam fails in one of two ways and the trade names them separately: the threads pull out of the cloth beside the stitching, or something breaks. Which one a given cloth does is decided by whether its seam allowance clears the length at which grip beats strength — and at the ordinary ten millimetres, the table divides four against four.

applied · Seams The size of the capstan correction. The ratio of the capstan crossover to the crossover a sum of independent contacts gives, for every cloth in the table at a friction coefficient of 0.30. It is exactly ln(1 + z)/z, where z is the thread's breaking load times the wrap angle, over the contact force — a quantity with no friction coefficient in it at all. That is why the earlier result that μ·L* is exactly constant survives this correction to twelve figures: μ was only ever in the factor outside the logarithm. The correction is largest for the duck, whose coarse strong yarn makes z large, and smallest for the batiste. What the rows cannot show is that a real cut edge frays at a friction nobody measured on that particular cloth.

How far a cut edge frays

A seam allowance, a fray width and a tuft's bound length are the same number wearing three hats, and the earlier estimate of it was four times too long. Correcting it moves the whole table across the boundary an ordinary allowance sits on — from four cloths holding and four slipping, to all eight holding — and turns a specification argument into a different one.

applied · Seams What a knit gives when it is pulled. Force against course-wise extension for a 20 tex cotton jersey at a 3.5 mm loop, computed from the loop's own bending with the relaxed shape as the yarn's natural one. The loop length is the same at every point on the curve: nothing here is the yarn stretching. It reaches 92% extension at 2.96 N per metre and then stiffens by a factor of 85 over the rest of the range, as the straight line between two interlacings runs up against the yarn between them. This is the number the collection's second phase recorded as a lower bound it could not compute, and it is still a lower bound in one respect: friction at the contacts is not in it, so a real fabric is stiffer than this and does not come back along the same curve.

A seam must give what the knit gives

A knitted seam fails because it is too short, not because it is too weak: the thread in it is nearly two thousand times stronger than the load it carries. What decides whether it survives is one line of geometry — the extension a seam can reach is twice the fabric's thickness times the stitches per unit length.

applied · Seams How hard each grouping holds its own threads. The grip a cloth has on one of its own threads inside a 10 mm seam allowance, for six members of the doubled family at 24 threads per centimetre and a friction coefficient of 0.3. Grip accumulates multiplicatively at every crossing — the capstan equation on Peirce's own weave angle — so it is exponential in the crossings, and the crossings are the interlacing rate times the intersections in the allowance. The family's interlacing rate has a closed form, (a + b)/2ab, which is half the sum of the two reciprocals — so the two groupings enter symmetrically and each one saturates. The dashed line is the thread's own strength: a cloth whose grip falls short of it lets the thread slide out rather than break, which is seam slippage. A 2/2 hopsack is below it at this allowance and a 1/4 warp rib is above, on cloths whose firmness differs by an eighth. What the bars cannot show is the friction coefficient, which is measured and is not a constant of cloth; the ordering holds at every value anybody reports and the sizes do not.

What nothing separates comes out together

The doubled family's interlacing rate has a closed form — half the sum of the two groupings' reciprocals — so a seam's grip on its own threads is the exponential of a harmonic mean, and it saturates in each grouping separately. At a ten-millimetre allowance a 2/2 hopsack holds a thread at seventy-four times the applied tension and a 1/4 warp rib at two hundred and eighteen, on cloths whose firmness differs by an eighth.

weaves · Rib weaves Every thread's interlacings in an eight-end satin stripe on a plain ground. An eight-end satin stripe on a plain ground on point paper, with a bar under every end and beside every pick for the share of its crossings at which it changes face. The warp's fewest is 0.25 a crossing against an average of 0.88, and the weft's 0.83 against 0.86; the draft's single firmness number is 0.87. What the bars cannot show is the friction at each crossing, which turns a count into a grip.

A cloth slips at its least-interlaced thread

A weave's firmness is quoted as one number, the interlacings per crossing averaged over the whole repeat. A cloth does not fail on average. A thread pulled through a seam or out of a cut edge is held by its own crossings, the grip is exponential in them, and the thread with fewest goes first. In every four-by-four draft but plain weave some thread interlaces twice a repeat — the fewest possible — whatever the average says, and a satin stripe on a plain ground averages 0.87 while its satin ends grip at a seventh of the average thread.

weaves · Firmness

Named alongside it

The objects these essays reach for when they reach for this one.

CapstanFrictionFloatFrayingSpecificationContact forceInterlacingFirmnessSeamSettCloth integrityCrossover length

All concepts