Textile Structure
how cloth is put together
Concept

Firmness — where it appears

Interlacings per intersection: how often the threads of a weave change face, which is what decides how tightly a cloth holds on to itself. It is decidable from the matrix alone, with no yarn diameter anywhere in it, and it runs opposite to the sett a cloth can be woven at.

Named by 13 essays across 5 fields — each of them below, with the objects they name alongside it.

What an interlacing costs. Each weave's interlacing count beside the closest it can be set in the same yarn. The two run opposite ways, because a thread that changes face often has to bend often and a bend takes room.

Interlacings and firmness

Every time a thread changes face it has to bend, and a bend takes room. That one sentence decides how densely a cloth can be set, how firm it feels, and why the two run in opposite directions.

weaves · Firmness Every cloth at 150 grams. The counts and setts that all weigh 150 g/m² at a crimp of 7 per cent and a balance of 1. Hollow marks are past the jam — arithmetic rather than cloth. Among the 10 that can be woven the cover factor runs from 0.28 to 0.77, a factor of 2.77, and every one of them is the fabric the specification asked for.

What a fabric weighs

Every fabric is sold by its weight in grams per square metre, and the number is a sum of four products in which no term appears alone. One equation, four unknowns: a hundred and fifty grams describes an open coarse cloth and a close fine one, and the cover factors differ by a factor of nearly three.

setting · Weight What holds a thread in a seam. A cloth thread inside a seam allowance, drawn past the crossings that grip it, with the capstan's factor at each. The tension falls by that factor at every crossing, so the grip is exponential in the crossing count and the count is what the weave decides. Beyond the thread's own strength the thread breaks rather than slides, and the rest of the allowance holds nothing.

What holds a thread in a seam

A seam fails in two quite different ways, and the one the trade worries about is not the stitches breaking. It is the cloth's own threads sliding out of the weave beside the seam — and what resists that is friction at the crossings, accumulating multiplicatively, so a satin gives a seam a thousandth of the grip a plain weave gives it.

applied · Seams The strain across a harness. The warp strain each shaft of a 24-shaft harness puts into its own ends, from 0.460 per cent at the front to 1.728 per cent at the back. Shafts within a budget of 1.0 per cent are drawn in one colour and those outside it in another; the budget is reached at shaft 13.

The back shaft works hardest

How hard the loom is on a warp end is the product of two numbers from different worlds — how often its column changes sides, which is a property of a binary matrix with no millimetre in it, and the strain of the shaft it happens to be on, which is a property of a machine with no weave in it. Neither knows about the other, and the threading that joins them is a decision nobody makes on structural grounds.

mechanics · Shed Plain weave, doubled. Plain weave, then the same weave with its picks grouped in 2, its ends grouped in 2, and both — which are a warp rib, a weft rib and a hopsack — and a 2/2 twill beside them for comparison. The rules under the drafts bracket the threads that lift together on every pick and so lie touching. Each doubling multiplies the cloth's own unit by 2: 2, then 4, then 8 intersections. The hopsack and the twill interlace equally often and are drawn from different rules. The setts under each draft are the densest that weave may be set at with a 0.25 mm yarn, and a rib's two are 0.750 apart where every other weave here is square.

A cord is a stripe with no colour in it

Warp rib, weft rib and hopsack are plain weave with its threads doubled, in the warp, the weft, or both. Six of the nine measures this site takes off a matrix cannot tell a 2/2 hopsack from a 2/2 twill, and the three that can are not the ones a weaver quotes.

weaves · Rib weaves A spread shading on 8 ends. The 7 tone steps of a spread shading on an 8-end repeat, each built by adding one more coset of the 8-end satin with move 3. Every coset has exactly one mark in every end and every pick, so the fraction of warp on the face is k over 8 exactly at every step, with no averaging in it. The numbers beneath are the longest float, and they run 7, 3, 3, 1, 3, 3, 7 — so the lustre scale is not the tone scale. The midtone is a plain weave and the extremes are satins, which is why a spread shading is at its most matt exactly in the middle. What the drafts cannot show is the surface: a long float stands proud of a short one, so an evenly toned shading is not an even surface either.

A shading changes two things at once

The tone steps of a shaded damask are exactly even — each adds one satin coset, so the fraction of warp on the face is k over n with no averaging in it. The lustre steps are not even at all: on eight ends the longest float runs 7, 3, 3, 1, 3, 3, 7, so a series that grades smoothly in tone is at its most matt exactly in the middle.

pattern · Shading The surface of an 8-end shading. The height of the cloth's own surface at each tone of an 8-end shading, for the two chains, on a sheeting at 0.50 N in the end. A thread presses on the thread it crosses only where it turns, so a region that turns more often is pressed more often and finishes thinner — and firmness rises towards the midtone of a shading. The spread chain therefore sinks 84 µm between its ends and its midtone and the consecutive chain 43 µm, with 2 of its steps at exactly one thickness against the spread chain's 0. The tone scale is level by construction and the surface under it is not. What the plot cannot show is the light: a step in the surface reads as a line under a raking beam whatever the tone is doing, which is why a relief nobody specified is visible at all.

A tone ramp is a valley, and the satin digs it

A shading's tone is exact and its lustre is measured; its thickness is neither, and nobody specifies it. A firmer weave is pressed harder at every crossing and finishes thinner, so an eight-end shading sinks eighty-four micrometres between its ends and its midtone — about a third of the cloth's whole thickness, on every cloth tried. Build the same chain on a twill instead of a satin and the sag is exactly nothing.

pattern · Shading The float a point fault gives a weave, over every draft there is. Every four-by-four draft that describes one cloth — 22,730 of them — laid out as 8 ends by 8 picks, with each intersection of its repeat reversed in turn and the longest float that produces kept. There are two answers and no others. 90 drafts hold the fault to a float of 3; 22,640 — 99.6% of every weave there is — hand it a float of 7. The mechanism behind the second number is that a reversal at a binding point joins the two floats on either side of it, so a weave with runs separated by single binding intersections gives a single mistake the sum of two of its own floats. The 90 that escape are the drafts whose floats are short and evenly spaced — the plain weave and the ribs — which is not the class of weave the trade recommends for hiding a fault.

Which weave hides a fault

The trade says a busy weave hides a mistake. Every four-by-four draft there is was laid out as cloth and given every wrong lift it could have, and ninety-nine in a hundred hand that single mistake a float of seven — because a reversal does not lengthen a float, it joins two.

weaves · Float Every 6-end decomposition, by the float its best chain holds the middle tones to. All 1,128,960 Latin squares of order 6 with their first row in order — every way of splitting a 6-end repeat into 6 parts with one mark in every end and every pick — each asked for its chains of tone steps. 2,816 can hold every tone between the extremes to a float of 2, and they fall into 64 classes once the repeat's starting corner and reading direction are set aside, the cyclic square a twill writes among them; 800,658 cannot do better than 4. 576 can put a plain weave at the midtone, and every chain that does floats three on either side of it. Every one of the 434,540 distinct tone steps met is one cloth. What the rows cannot show is which of the classes a designer would choose, since the float profile is one criterion among several.

A six-end shading can be even or have a plain centre, not both

A six-end repeat can be split into the parts a shading is built from in 1,128,960 ways, and every one of them has now been walked. Only 2,816 — sixty-four distinct shadings — hold every tone between the extremes to a float of two, and seven in ten cannot do better than four. Five hundred and seventy-six can put a plain weave at the midtone, and not one of those can keep twos beside it: taking a part out of a plain weave, or adding one, always leaves a float of three.

pattern · Shading How hard each grouping holds its own threads. The grip a cloth has on one of its own threads inside a 10 mm seam allowance, for six members of the doubled family at 24 threads per centimetre and a friction coefficient of 0.3. Grip accumulates multiplicatively at every crossing — the capstan equation on Peirce's own weave angle — so it is exponential in the crossings, and the crossings are the interlacing rate times the intersections in the allowance. The family's interlacing rate has a closed form, (a + b)/2ab, which is half the sum of the two reciprocals — so the two groupings enter symmetrically and each one saturates. The dashed line is the thread's own strength: a cloth whose grip falls short of it lets the thread slide out rather than break, which is seam slippage. A 2/2 hopsack is below it at this allowance and a 1/4 warp rib is above, on cloths whose firmness differs by an eighth. What the bars cannot show is the friction coefficient, which is measured and is not a constant of cloth; the ordering holds at every value anybody reports and the sizes do not.

What nothing separates comes out together

The doubled family's interlacing rate has a closed form — half the sum of the two groupings' reciprocals — so a seam's grip on its own threads is the exponential of a harmonic mean, and it saturates in each grouping separately. At a ten-millimetre allowance a 2/2 hopsack holds a thread at seventy-four times the applied tension and a 1/4 warp rib at two hundred and eighteen, on cloths whose firmness differs by an eighth.

weaves · Rib weaves Every thread's interlacings in an eight-end satin stripe on a plain ground. An eight-end satin stripe on a plain ground on point paper, with a bar under every end and beside every pick for the share of its crossings at which it changes face. The warp's fewest is 0.25 a crossing against an average of 0.88, and the weft's 0.83 against 0.86; the draft's single firmness number is 0.87. What the bars cannot show is the friction at each crossing, which turns a count into a grip.

A cloth slips at its least-interlaced thread

A weave's firmness is quoted as one number, the interlacings per crossing averaged over the whole repeat. A cloth does not fail on average. A thread pulled through a seam or out of a cut edge is held by its own crossings, the grip is exponential in them, and the thread with fewest goes first. In every four-by-four draft but plain weave some thread interlaces twice a repeat — the fewest possible — whatever the average says, and a satin stripe on a plain ground averages 0.87 while its satin ends grip at a seventh of the average thread.

weaves · Firmness The selvedge turns of a 2/2 twill, 4 ends wide, from the left. A strip of 2/2 twill 4 ends wide over 8 picks, the first thrown from the left, with the weft's turn between every pair of picks drawn at the edge it reaches. 0 of the 8 turns are caught, where the edge end is on the other face on the second pick, and 8 slip. Across all its edge placements the weave catches every turn at 8 of 16. What the drawing cannot show is how far a slipped loop travels, which the beat-up and the weft tension decide.

A selvedge holds only where its edge end changes face

A shuttle weft goes out on one pick and back on the next, and between them it turns round the end at the edge. The turn is caught only if that end is on the other face on the second pick; otherwise the loop has nothing to wrap and slides off. Plain weave catches every turn at every width. A 2/2 twill catches them at half its widths, and only if the first pick is thrown from the right side. A 3/1 twill, a hopsack and every satin catch them nowhere, and of the 22,874 four-by-four drafts, 9,636 cannot hold a selvedge at any width at all.

weaves · Firmness The surface of every even six-end shading, against the twill's. The height of the cloth's surface at each tone of a six-end shading on a sheeting at 0.50 N, for every chain of the 64 even classes, drawn once per distinct shape — 5 of them — and for the cyclic square's twill read one step at a time. The twill is level to the micrometre and floats 5, 4, 3, 4, 5. Every even chain sinks to exactly 43.3 µm at its midtone; the shapes differ only at the second and fourth tones. What the plot cannot show is which of these a raking light would reveal, which depends on the finish.

An even shading cannot keep its surface level

Sixty-four six-end shadings hold every middle tone to a float of two, and the question left over was whether any of them keeps a tone ramp's surface level the way a twill read in order does. None does, and all of them sink by exactly the same depth — 43.3 micrometres on a sheeting, a sixth of the cloth. The reason is a counting argument a recording engineer would recognise: a limit on how long a thread may float is a limit on run length, and a run-length limit forces a floor on how often the thread changes face. A level ramp needs every tone at the extremes' rate, which needs a float of half the repeat at the midtone and more beside it — exactly the floats the twill in order has.

pattern · Shading

Named alongside it

The objects these essays reach for when they reach for this one.

InterlacingFloatShadingToneCapstanCensusEnumerationFloat lengthSeam slippageSettCloth thicknessDamask

All concepts