Textile Structure
how cloth is put together
Concept

Crossover length — where it appears

The gripped length at which a thread being withdrawn breaks rather than slides, which is how far a cut edge frays. It is a fixed-force question rather than a fixed-length one, and that distinction decides whether the interlacing ordering between weaves is exact.

Named by 7 essays across 5 fields — each of them below, with the objects they name alongside it.

A thread withdrawn from a plain weave and from a satin. One pick of a sheeting being pulled from 1.60 mm of cloth, in a plain weave and in a five-end satin, at a friction coefficient of 0.30. The drawn width of each thread is the tension in it at that point, to a common scale; the faint rules are where the thread actually turns, which is at its interlacings and nowhere else. A plain weave turns 2.80 times per millimetre and a satin 1.12, so the plain weave's tension compounds 2.78-fold over this length against the satin's 1.46. What the drawing cannot show is that the wrap angle is taken from a plain-weave geometry in both panels: a satin's crimp is genuinely smaller, so its real turns are gentler than these and its grip weaker still.

A thread is gripped where it turns

The arithmetic this site has used for fraying, seam slippage and tuft anchorage counts every crossing a thread makes as a grip and adds them up. A thread lying flat on the surface of a satin presses on nothing at all, and a thread that is gripped is gripped by a friction that compounds along its length rather than adding. Both corrections were recorded as missing and both are here.

cloth · Contact The size of the capstan correction. The ratio of the capstan crossover to the crossover a sum of independent contacts gives, for every cloth in the table at a friction coefficient of 0.30. It is exactly ln(1 + z)/z, where z is the thread's breaking load times the wrap angle, over the contact force — a quantity with no friction coefficient in it at all. That is why the earlier result that μ·L* is exactly constant survives this correction to twelve figures: μ was only ever in the factor outside the logarithm. The correction is largest for the duck, whose coarse strong yarn makes z large, and smallest for the batiste. What the rows cannot show is that a real cut edge frays at a friction nobody measured on that particular cloth.

How far a cut edge frays

A seam allowance, a fray width and a tuft's bound length are the same number wearing three hats, and the earlier estimate of it was four times too long. Correcting it moves the whole table across the boundary an ordinary allowance sits on — from four cloths holding and four slipping, to all eight holding — and turns a specification argument into a different one.

applied · Seams How much too thick a round section is, and what reconciles it. For each cloth in this site's table: the thickness a circular Peirce section predicts, the thickness a cloth of that construction measures, and the force per crossing that makes the flattened model reproduce the measurement. The over-prediction runs from 36% to 81%. The reconciling forces span a factor of 4.6 across a table whose counts span a factor of six, and every one of them is of the order of the contact force the cloth's own warp tension supplies — which is what makes this a model rather than eight fitted parameters. What the rows cannot show is that the thicknesses are trade figures for cloths of these constructions rather than measurements of these particular fabrics, so what is being read is an ordering.

The relaxed cloth's contact force

How hard two threads press on each other in a cloth that is not being pulled is the number this site's own integrity criterion has needed since its first essays, and the route to it was an elastica nobody had. A thickness gauge supplies it instead — because a cloth's thickness is a record of how flat its threads are, and how flat they are is a record of how hard they are pressed.

mechanics · Compression The crossover length in four weaves. The gripped length at which a pick of a sheeting breaks rather than slides, in four weaves at a friction coefficient of 0.30. It is a millimetre or two for a plain weave and 8.0 mm for an eight-end satin, which is what a cut edge of each does. The interlacing rate appears in the answer only as a factor outside the logarithm, so the ratios between the four are exactly the ratios of their interlacing rates — in this model and in the sum of independent contacts alike. The rung below expected the float correction to change that ordering; it does not. It changes the size, by a factor of 3.7. What the rows cannot show is that all four use one cloth's crimp, so a satin's genuinely gentler turns are not in them.

A float presses on nothing

The rung below expected the float correction to change how a satin's hold compares with a plain weave's, by something like the ratio of their interlacing rates. It does not change the comparison at all — the interlacing rate leaves the answer outside the logarithm and divides straight out of any ratio. What it changes is the absolute answer, by a factor of four, for every weave alike.

weaves · Float What a raising machine can catch in a 2/2 twill. The draft with every weft float long enough for a raising wire to lift marked on it. The teeth need an unsupported length of thread on the surface, so a cloth in which every thread is bound at every crossing offers them nothing at all — which is why a napped fabric is always a twill or a satin and never a plain weave.

What holds a nap in a knit

A fibre buried in a woven cloth breaks rather than slides once about thirty-four millimetres of it is held, and a cotton staple buries about fourteen. In a knit the same figure is over a metre — seventy-five times the burial available — so nothing is ever close, and a raised knit sheds for the whole of its life.

finishing · Nap What holds a thread in, as two factors. The two quantities whose product is the grip on a buried thread, for a woven poplin and a jersey of the same yarn. Each contact in the knit is lighter by 8.0 times, and the contacts are further apart by 5.6 — one per half loop length against one per thread spacing. They multiply rather than competing, so the grip per millimetre of buried thread is 31 times weaker in the knit, and the crossover length at which a thread breaks rather than slides moves with it: 11.6 mm in the cloth and 461 in the knit. The two factors are drawn separately because their product is two orders of magnitude and a bar chart of it would put the knit's bar below the width of a line.

The knitted pilling criterion gets its number

Knitwear pills and shirting does not, and the standing explanation here has been that a knit presents more exposed yarn under less pressure between its threads. The second half had no number. It has one now, and it is bigger than the argument needed: the grip on a buried fibre is thirty times weaker in a knit than in a woven cloth of the same yarn.

applied · Pilling What a run has to overcome. The friction holding one loop in the loop below it, against how tightly the fabric is knitted. It is the coefficient of friction times the contact force times the two interlacings a stitch makes, and it runs from 14.7 to 35.1 millinewtons across the knittable range — a factor of 2.4 for a factor of under two in tightness factor, because the contact force and the tightness move together. That is the arithmetic behind a rule every knitter has: a slack fabric runs and a tight one does not, and tightening it is the only lever that works. The figures are upper bounds, since a set yarn presses less.

A run is a race between two energies

A dropped stitch travels when a loop can be pulled out of the loop below it, and there are two candidate drivers: the energy the loop releases by unravelling, and the load the garment is under. One of them turns out to be negligible, and knowing which changes what a knitter can do about it.

applied · Damage

Named alongside it

The objects these essays reach for when they reach for this one.

Contact forceFrictionPull-outSpecificationCapstanFloatFrayingLoop lengthIntegrityInterlacingPillingSeam slippage

All concepts