Concept

Relaxation band — where it appears

The interval a fabric's resting length may lie anywhere inside, because friction holds its crossings wherever they were left. Its width is friction over stiffness, which means a limper yarn gives a wider band and the softest cloths are the least dimensionally repeatable.

Named by 4 essays across 2 fields — each of them below, with the objects they name alongside it.

Wash-by-wash shrinkage, reported and modelled. The shrinkage an unfinished cotton cloth shows in each of five laundering cycles, beside what a model with no rate in it predicts. The model says a wash lets every crossing whose frictional barrier is below the cloth's current excess slip to the edge of its own band, and that is a distribution rather than a rate. Two numbers are fitted — the excess the cloth came off the loom with, 7.13%, and the spread of the barriers, 37.2× — against the first two washes. Washes three, four and five are predictions with nothing left to adjust and come out at 0.506%, 0.284%, 0.179% against reported 0.50%, 0.30%, 0.20%. What the bars cannot show is the finding underneath: the reported yarn-on-yarn friction range gives a spread of only 1.34×, which would have the tail over by the third wash.

A cloth shrinks most the first time

A laundering test reports five numbers and they fall away like a geometric series. Nothing in a wash is slow — a cloth is agitated tens of thousands of times in half an hour — so a second wash that shrinks it again is direct evidence that its frictional barriers are spread, and the ratio between successive washes measures how far.

finishing · Shrinkage
What a tensioned sheeting has left of its load. A sheeting pulled to a strain, clamped at that length and left. Its length does not change, and its load does: crossings rearrange locally until the load has fallen to what friction alone can hold, which is 0.0756 N per end and is the same number whatever the cloth was pulled to. So the fraction retained is that floor over the load applied, and it falls — a cloth tensioned to 4.94 per cent keeps 29 per cent of what it was given. Below the resting band's own edge nothing is lost at all, because the cloth was never outside what friction could hold. What the plot cannot show is time: nothing here says how long the rearrangement takes, only where it stops.

A tensioned cloth loses its load

Clamp a fabric at a fixed length and its tension falls overnight. Nothing crept and nothing flowed: the crossings rearranged locally until the load had dropped to what friction alone can hold, and that level is the same number whatever the cloth was pulled to — so the harder it was tensioned, the smaller the share it keeps.

mechanics · Set
The load each cloth settles to, held one way and held both. The frictional floor per thread of eight cloths at a friction of 0.3, warp then weft, with the other system free and with both held on a frame: cheesecloth, warp 0.034 rising to 0.035, weft 0.012 rising to 0.018 N; voile, warp 0.043 rising to 0.050, weft 0.031 rising to 0.042 N; batiste, warp 0.051 rising to 0.064, weft 0.044 rising to 0.060 N; muslin, warp 0.055 rising to 0.069, weft 0.045 rising to 0.064 N; duck, warp 0.064 rising to 0.089, weft 0.058 rising to 0.087 N; filter, warp 0.066 rising to 0.094, weft 0.061 rising to 0.092 N; poplin, warp 0.078 rising to 0.084, weft 0.022 rising to 0.055 N; sheeting, warp 0.076 rising to 0.115, weft 0.070 rising to 0.113 N. The rise is largest where the other system is steeply crimped. The figure assumes one resting contact force for every cloth, and cannot show the spread of friction across a piece.

A cloth held both ways settles higher

A cloth clamped at one length settles at a load friction alone can hold, whatever it was pulled to. That floor took the pressing at each crossing as given. On a frame it is not: the other system's tension presses every crossing too, so the two floors depend on each other and have to be solved together. A sheeting settles half as high again on a frame, a poplin's weft two and a half times, and a dead weight on one system lifts the other in a straight line. Re-tensioning still buys nothing. Weight does, and at a friction no cotton reaches, nothing would relax at all.

mechanics · Set
What squaring a sheared frame costs a sheeting's ends. The share of a framed sheeting's settled warp load lost after a shear is held, settled and squared again, against the shear angle, for a cloth clamped at 4.45%, which loses 19% to a 3° shear and goes slack at 6.9°; at 4.65%, which loses 28% to a 3° shear and goes slack at 5.7°; at 4.85%, which loses 48% to a 3° shear and goes slack at 4.3°. A frame that racks on its pins keeps every thread's length and loses nothing at any angle, which is the flat line along the foot. The loss is quadratic in the angle because a sliding rail stretches the ends by 1/cos γ − 1. The picture assumes the settled cloth unloads along the loading curve's own slope, and cannot show how long a shear must be held to settle.

A frame squared again keeps less than it had

A cloth settled on a frame holds its floor, and a frame does not stay square. Whether going out of square costs anything depends on the frame, not the cloth. A frame that racks on its pins keeps every thread's length and loses nothing. A frame whose rail slides along itself stretches the ends by the square of the angle, and squaring it again leaves them short. A sheeting loses a sixth of its warp load to a three-degree shear, the picks lose load they were never asked to carry, and the next shear of the same size takes only an eighth as much again.

mechanics · Set

Named alongside it

The objects these essays reach for when they reach for this one.

Frictional floorYarn frictionPermanent setContact forceCrimp interchangePre-tensionTensile locusAgitationBending rigidityInterchange budgetLoad-extensionPre-shrinking

All concepts