Textile Structure
how cloth is put together
Concept

Fibre count — where it appears

How many fibres cross any plane through a yarn: the yarn's count divided by one fibre's, and a division with no geometry in it. It decides three quite separate things — a yarn's diameter in fibre diameters, the width of its stiffness bracket, and the floor under its evenness — and the last two run in opposite directions.

Named by 18 essays across 6 fields — each of them below, with the objects they name alongside it.

The evenness a cotton yarn cannot be better than. Lay staple fibres down at random and count how many cross a plane: the count is Poisson, its variance is its mean, and the coefficient of variation of the mass per unit length is therefore 1/√n with no material and no machine in it. The lower curve is that floor. At 20 tex there are 118 fibres in the section and the floor is 9.93 per cent; at 5 tex there are 29 and it is 19.86. The upper curve is what a yarn spun at an index of irregularity of 1.35 actually measures, which is the floor times a constant — so the whole shape belongs to the counting and none of it to the spinning. The exponent is exactly −½ and is asserted as such rather than fitted to the curve.

The spread was never free

This collection has taken a yarn's irregularity off a delivery note and used it as an input. It is not an input. Counting the fibres in a cross-section puts a floor under it that no spinner can beat, and the floor is one over the square root of the count.

cloth · Variation The two diameters of a 20 tex yarn. The pressure inside a twisted yarn is zero at its surface, so the outermost fibres are held by nothing but their own buried ends and some of them stand off as loops and ends. A yarn therefore has two diameters: a mass diameter of 167.1 µm, which is a volume divided by a length and is the one every other calculation on this site uses, and a contact diameter of 217.1 µm, which is what a neighbouring thread, a finger or an air stream meets. The gap is a hair layer of 25.0 µm on each side and it is measured, not computed — nothing here predicts hairiness. What is computed is the consequence, and it is 29.9% of the diameter every cover factor on this site was built from.

The hairs are what touch

The pressure inside a twisted yarn falls to exactly zero at its surface, so the outermost fibres are held by nothing and some of them stand off. A yarn therefore has two diameters — the one its mass gives and the one a neighbour meets — and only the first is in the arithmetic.

cloth · Hairiness How much of a 20 tex yarn's unevenness survives being woven. Weaving averages, and the averaging is a square root. A patch of cloth 3 mm across contains 7.2 warp threads and as many picks, each contributing its own mass independently, so the patch's coefficient of variation is 3.53% against the yarn's 13.4% — a reduction of 3.8-fold. The rule at the top is the yarn's own figure. The curve steepens past the staple length, where a patch starts to contain independent samples along each thread as well as across them, and the second regime is the one a large area of cloth is judged in.

A cloth cannot be more even than its yarn

It can be very much more even than its yarn, and by exactly the square root of the threads in view. Which raises a question the fineness argument left open — and the answer is that at a fixed cloth weight the count cancels out entirely.

pattern · Variation A V-fastened tuft. A cut pile bound into its ground by V fastening, drawn in section. The pile end passes beneath 3 of the 6 ground picks and wraps 1 half-turn around them in all. The integrity criterion says the tuft is attached; how hard it is held is a different question with a different model behind it.

A chenille is a yarn that is already a fabric

A chenille yarn is a woven gauze cut into strips. Every structural question this collection asks about cloth can be asked about it — does it hang together, how many systems has it, what holds the pile in — and the answers are the same answers one level down.

fancy · Fancy yarn A 20 tex cotton yarn and the fibre standing off it. 6 mm of a 20 tex ring-spun cotton yarn with the hair population this site computes from the yarn's own count and staple — 0.89 hairs per millimetre, every one of them drawn. The two axes are at different scales and have to be — the yarn is 167 µm across and its hairs reach past a millimetre, so a picture at one scale is either a bare line or a black rectangle. Along the yarn is 99 pixels to the millimetre and off it is 74, a 1-fold exaggeration of the vertical. Lengths are drawn from the exponential the model predicts, mean 621 µm; the rules mark one, two and three millimetres with the count a hair-counting instrument reports at each, and the hairs crossing each rule in the drawing are the ones those counts are about. At the yarn's own surface the long hairs cover 1.1% of the space beside it, which is why the picture is mostly gap. Nothing here is the short population, which carries most of the protruding length and none of the reach; and a hair reaching past the room the canvas has is drawn to the edge of it, so the very longest few are shortened in the drawing and not in the arithmetic.

A yarn's surface is a distribution

This collection has computed where a cloth stops, and every one of those numbers is a statement about yarn. What a finger, a plate, a droplet or a ray of light actually meets first is a population of fibre ends standing off the yarn — and it is a population, with a count and a length, rather than a layer with a thickness.

cloth · Hair layer 20 tex, counted. The cross-section of a 20 tex cotton yarn, with every fibre in it drawn. The count is a division and nothing else: a 20 tex yarn spun from 0.17 tex fibre has 117.6 fibres crossing any plane through it, and the yarn is 14.0 fibre diameters across because n fibres packed at 0.6 fill a circle √(n/φ) times as wide. The arrangement is drawn on a lattice and is not claimed: real fibres are not on one, they migrate between the core and the surface as they run, and everything this collection says about a yarn's strength turns on their doing so.

How many fibres make a thread

Every number in this collection began with a diameter, and a diameter is not a measurement — it is a count of fibres, divided. Once the division is written down, three quantities that had nothing to do with each other turn out to be the same number.

setting · Assembly Where a 20 tex yarn breaks, against how much was clamped. A tensile test clamps a length of yarn and pulls until the thinnest section between the clamps gives. So a yarn's strength is a minimum, and a minimum depends on how many independent tries the sample contains. The tries are not sections — a plane can be taken anywhere — but staple lengths, because two planes closer together than one fibre share most of their fibres. At 28 mm staple a 100 mm specimen holds 3.6 independent tries and a 500 mm one holds 17.9, and the longer test reads 11% lower. The spread is not fitted either: it is the evenness floor at 118 fibres times an index of 1.35, which is 13.4%.

A yarn breaks at its thinnest place

A tensile test does not measure a yarn. It measures the worst section between the clamps — so evenness and strength are one measurement taken twice, and the number of independent tries in a specimen is set by the length of a fibre.

mechanics · Assembly The evenness a cotton yarn cannot be better than. Lay staple fibres down at random and count how many cross a plane: the count is Poisson, its variance is its mean, and the coefficient of variation of the mass per unit length is therefore 1/√n with no material and no machine in it. The lower curve is that floor. At 5 tex there are 29 fibres in the section and the floor is 19.86 per cent; at 5 tex there are 29 and it is 19.86. The upper curve is what a yarn spun at an index of irregularity of 1.35 actually measures, which is the floor times a constant — so the whole shape belongs to the counting and none of it to the spinning. The exponent is exactly −½ and is asserted as such rather than fitted to the curve.

A finer yarn is a worse yarn

Fineness is the thing a yarn is priced for, and it is bought with irregularity at a fixed exchange rate. Once the spread is a function of the count, every correction this collection computes becomes a function of the count too — and the cheapest yarn on the shelf is the one the arithmetic describes best.

setting · Assembly Where the strain goes, at a 25° twist. Extend a twisted yarn and the fibres in it are not all strained alike. If each stays at its own radius — the affine model — a fibre at helix angle θ takes cos²θ of the yarn's strain, so the fibre on the axis takes all of it and the fibre at the surface takes 82.1% of it. The core reaches its breaking extension first and the yarn cannot realise its own fibres. If instead every fibre migrates between the core and the surface, every fibre has the same mean strain and they all break together. The two are exactly computable — 0.8214 against 0.9509 of what the fibres could give — and the ratio between them, 2/(cos α(1 + cos α)) = 1.158, is what migration is worth. The shading is that arithmetic and the two panels use the same scale.

A straight fibre cannot share the load

Extend a twisted yarn and its fibres are not all strained alike: the one on the axis takes the whole of it and the one at the surface takes cos²α. So they do not break together, and what a wandering fibre is worth comes out as one expression with nothing fitted in it.

mechanics · Migration Folding improves the evenness and not the yarn. Two independent singles of 15% give a fold of 10.61%, because independent errors add in quadrature: an improvement of exactly √2. The floor falls by exactly √2 as well, from 9.93 per cent to 7.02, because the fibre count is 2 times what it was. So the index of irregularity is unchanged — 1.511 before and 1.511 after, equal to twelve figures, not merely close. Folding does not make a better yarn; it makes a bigger one, and every part of the improvement is the part the count was going to give anyway. What folding does buy is elsewhere: the torque, the surface, and where the grip comes from.

A two-fold yarn is not twice a single

Folding halves nothing. It improves a yarn's evenness by exactly √2 and lowers the floor that evenness is measured against by exactly √2, so the index of irregularity comes out identical — folding does not make a better yarn, it makes a bigger one.

setting · Ply Which end of the bracket a thread in cloth is at. A yarn bends as a solid rod while its fibres cannot slide and as a loose bundle once they can, and the crossover is a curvature: the coherent state demands an axial force in the outer fibre that has to be built up by friction under the twist's own radial pressure. The curves are the crossover radius against twist at four contact efficiencies, the top one being 1.0 — the claim that fibres touch along their whole length, which nobody makes. The rule at the bottom is the radius a thread is bent to by its own crimp in a cloth, about 0.25 mm. Every curve is above the rule by at least 19-fold, so a thread in cloth is at the free end of its bracket at every twist and every efficiency, and the collection's habit of using the lower bound is a result rather than a convention.

Twist decides where in the bracket

A yarn's bending rigidity can only be bracketed, and the bracket is three hundred wide. What decides where a yarn sits in it is whether its fibres can slide — and for a thread bent by its own crimp in a cloth, the answer is not close.

mechanics · Yarn stiffness The depth belongs to the fibre and the density to the yarn. Over a 5-fold range of cotton yarn counts, the hair layer's decay length moves by 6.2% and its population moves by 2.37-fold against a square root of 2.24. Both follow from one cancellation. The shell's share of the section is 4d_f/D, the migration period is a fixed number of yarn diameters, and λ = ½(kD)(4d_f/D) — the yarn's diameter divides out and leaves λ = 2k·d_f, a length belonging to the fibre alone. The density has no such cancellation and goes as √(nφ)/L. The two small departures visible here are not two facts: they are the shell's second-order term, and they are the same number to the last bit of a double. The consequence for a spinner is that a coarse yarn is hairier and its hairs are no longer, so everything that depends on reach — pilling, prickle, a printed edge — is decided by the fibre and not by the count.

Hairiness goes as the root of the count

A coarse yarn is hairier than a fine one and everybody knows it. What nobody has said is that its hairs are no longer — the count and the length obey different laws, one rises as a square root and the other does not move at all, and the identity behind both was asserted on this site for an entirely unrelated reason.

setting · Hair layer A knot, and the tension falling through it. A 20 tex cotton thread wrapped through 1 turn at a bend radius of 1 yarn diameters, with a coefficient of friction of 0.30. The wrap is drawn as a spiral because a thread taken round a pin comes back beside itself rather than onto itself. The marks round it are the fraction of the entry tension still there: 100%, 69%, 47%, 32%, 22%, 15%. The bend has already spent 3.6% of strain at the outside of the thread before any of that happens, against a breaking strain of 6.6%. So the largest total is at the entry, before the knot has done any gripping at all — which is where a knot in a real yarn is observed to break, and why a knot's efficiency is a property of its first bend rather than of the knot.

A knot is nothing but contact

A knot has no fastening in it. Nothing is glued, hooked, sewn or threaded through a hole: a thread is bent round itself until the friction where it presses on itself is more than the load. That makes a knot the purest contact problem in the subject, and the place to look first for what contact does.

applied · Contact A knot, and the tension falling through it. A 20 tex cotton thread wrapped through 1 turn at a bend radius of 1 yarn diameters, with a coefficient of friction of 0.30. The wrap is drawn as a spiral because a thread taken round a pin comes back beside itself rather than onto itself. The marks round it are the fraction of the entry tension still there: 100%, 69%, 47%, 32%, 22%, 15%. The bend has already spent 3.6% of strain at the outside of the thread before any of that happens, against a breaking strain of 6.6%. So the largest total is at the entry, before the knot has done any gripping at all — which is where a knot in a real yarn is observed to break, and why a knot's efficiency is a property of its first bend rather than of the knot.

Where a knot breaks

It breaks at the entry, before the knot has done any gripping at all. Two quantities run along a knot's path and only one of them rises; the other falls from the first millimetre; and their sum is largest where the thread arrives.

applied · Damage What a knot costs, and what decides it. Knot efficiency against the radius the thread is bent to, for 5 fibres at 20 tex, computed at the free end of the stiffness bracket — each fibre bending about its own axis, so the strain at the outside of the bend is half a fibre diameter over the radius. At one yarn diameter of radius, cotton keeps 46%, which is the rule of thumb that a knot halves a rope's strength. What separates the curves is not the knot and not the friction: it is the fibre's own breaking strain, which is how much the bend is allowed to spend before there is nothing left.

A knot halves a yarn and says why

The rule is quoted for every rope and every knot and derived nowhere. It comes out at forty-six per cent for a cotton — but only if the yarn's fibres bend individually. A yarn bending as a solid section has already spent five times its breaking strain before any load arrives, so it could not be knotted at all.

applied · Tensile What a knot costs, and what decides it. Knot efficiency against the radius the thread is bent to, for 5 fibres at 20 tex, computed at the free end of the stiffness bracket — each fibre bending about its own axis, so the strain at the outside of the bend is half a fibre diameter over the radius. At one yarn diameter of radius, cotton keeps 46%, which is the rule of thumb that a knot halves a rope's strength. What separates the curves is not the knot and not the friction: it is the fibre's own breaking strain, which is how much the bend is allowed to spend before there is nothing left.

Which yarns knot well

A knot's efficiency depends on three things and only one of them is the knot. The other two are the fibre's fineness and its breaking strain, and across this collection's own table those give efficiencies from six per cent to eighty-three at exactly the same bend.

applied · Tensile A fibre's two stiffnesses, as the ratio that survives the bracket. C over B for every fibre in the table, at 20 tex, which is 2G/E and nothing else. The mark beyond each bar is the range the shear modulus is reported over. Glass is the control and is not a measurement: it is a drawn isotropic solid, so its ratio must be 1/(1+ν) and at ν = 0.2 that is 0.833, which is what the table says. Every fibre with molecules drawn out along its axis sits below the isotropic value, and the ordering is the subject rather than an accident — a fibre is stiff along its axis because its molecules are drawn out along it, and the same orientation that raises E leaves G to whatever holds one chain to the next. Aramid, the most oriented thing here, is twenty times softer in torsion relative to its bending than the glass beside it.

A thread has a second stiffness

Every mechanical number here came from one material constant: how hard a thread is to bend. A thread also resists being twisted, nothing here has ever used that, and the ratio between the two turns out to be the only stiffness number about a yarn that can be known at all.

mechanics · Torsion Two stiffnesses, one bracket, and a ratio that does not move. The bending and torsional rigidities of a cotton yarn against its count, each drawn at both ends of its own bracket, on a logarithmic scale. The four curves are two parallel pairs: the torsional bracket is the bending bracket exactly — the fibre count over the square of the packing factor, 327 at 20 tex — so the vertical gap between the two bounds is the same for both deformations. The consequence is the useful part: the ratio C/B is 0.250 at the top of the bracket and at the bottom and everywhere between, because the polar second moment of a circle is exactly twice its flexural one.

A fabric reads its own bracket four ways

A yarn's stiffness is unknown to a factor of three hundred, and no laboratory measurement has closed it. Four unrelated everyday observations — a snarl, a knot, a flattened yarn and a cloth's own thickness — all say the same thing about which end of it a yarn sits at.

mechanics · Yarn stiffness

Named alongside it

The objects these essays reach for when they reach for this one.

Bending rigidityPacking factorSpecificationTenacityCoefficient of variationContactFibre finenessLimit irregularityStaple lengthYarn countDamageFriction

All concepts