Textile Structure
how cloth is put together
Concept

Surface height — where it appears

The height of a woven cloth's outside above its own mid-plane, at every point of the plan. It is computed rather than measured: the draft says which thread is on the face, Peirce's geometry says how high that thread's centre line rides, and the thread's own section adds its radius on top.

Named by 13 essays across 6 fields — each of them below, with the objects they name alongside it.

The surface of a 2/2 twill, in plan. One repeat of a 2/2 twill in sheeting, drawn 2 × 2 times, with every point painted in the colour of whichever thread owns the outside of the cloth there and at an opacity set by how high it is. The range is 221.0 µm from the highest point to the lowest, the root-mean-square roughness is 74.9 µm, and 30% of the plan is hole rather than surface. The bright ribbons are the float plateaux, where a thread lies straight across the threads it passes over and its outside is a horizontal line rather than a point — which is the whole of what follows. The warp crowns at 190.8 µm and the weft at 182.8 µm, a step of 8.0 µm, so the cloth touches the world on its warp alone until anything pressing on it has sunk that far.

A cloth has an outside

Every quantity in this collection is a property of the inside of a fabric — a crimp, a cover, a hole, a fibre count. None of them says where the cloth stops. The outside is a height field the draft computes, its crowns stand at two different levels, and which of the two is higher decides what the cloth touches the world with.

cloth · Surface The bearing curves of 4 weaves in one cloth. How much of the plan is within a given depth of the highest point, for plain, 2/2 twill, satin 5, satin 8 — all in sheeting, all at the same sett, the same counts and the same thickness. They differ only in their drafts. At a hundredth of the cloth's thickness the last of them is touching 9 times the area of the first, and the gap widens as the depth shrinks, because the curves do not merely differ by a factor — they have different exponents. A crown that is a line opens as the square root of the depth and a crown that is a point opens in proportion to it.

The curve that says what a cloth touches with

Take a cloth's surface and ask what fraction of the plan lies within a given depth of its highest point. The answer is one curve, it answers every question of the form what does this touch, and its behaviour at the top is decided by a single bit of the draft — whether the longest float is one crossing or more than one.

cloth · Surface A damask's figure and ground trade places when the cloth is turned. A satin 8 figure on a sateen 8 ground in sheeting — one cloth, one set of threads, one sett, and the ground is the figure's own complement. Their total specular areas are within a few per cent of one another, so neither is intrinsically the brighter. What differs is the direction: the figure's crowns run with the warp and the ground's with the weft. So the contrast between them is 2.0-to-one with the light coming from 8° and 0.47-to-one from 90° — it reverses, exactly, a quarter turn apart. That is what makes a damask visible in one colour, and it is not the step in its surface: the step is fifty micrometres and returns no light at all under a diffuse illumination, while this contrast is a factor of 2.0 and is present whenever there is a direction in the light.

A figure shows by its shine, not its step

A damask is one cloth in one colour and its pattern is plainly visible. This collection attributed that to the step in its surface — fifty micrometres of relief, computed from the interlacing rates. The step is real and returns almost no light. What makes the figure visible is that its crowns run at right angles to the ground's, so the two trade places when the cloth is turned.

pattern · Blocks single jersey, as loops. Three courses of the same structure drawn as yarn. A knitted needle takes a new loop through the one below; a tuck takes the yarn into the loop below and leaves it on the needle, so that loop is held for another course; a miss floats straight past. Six needles is as many as a loop diagram can carry, which is why the array beside it exists.

A jersey has two surfaces

The face of a plain knit shows the legs of its loops, which run along the wale; the back shows the heads and feet, which run across it. So the two faces carry their crowns at right angles — the same situation as a damask's figure and its ground, in a fabric with no warp, no weft and no float.

knits · Knit What it costs to touch a cloth. The pressure needed to bring a stated fraction of the plan into contact, for plain, 2/2 twill, satin 8 in sheeting. Reaching two per cent of the plan takes 2.83 kPa on a plain and 0.05 on a satin 8, a factor of 55. The stiffness in this figure is fitted and is labelled as such. A yarn's resistance to being squashed out of round has no lower bound at all — a bundle of fibres free to slide is a fluid in cross-section — so no bracket exists to compute this from, and what is used is the value this collection fitted to measured fabric thickness. Every curve moves together across its published range, which is why the ratio between weaves survives and the absolute values are quoted with the fit named.

How much of a cloth is touching

Press a fabric against a flat plate with the weight of a hand and ask what fraction of it is actually in contact. The bearing curve answers, and the answer is about four per cent — of which the great majority is not the cloth's surface at all, but the hairs standing off it, which nothing in this arithmetic can see.

cloth · Contact A slack twisted yarn takes a coil of one size. A 20 tex cotton at 1400 turns a metre. Its own torque is 2.060 µN·mm at the free bound, and a rod under tension T is stable while its torque stays under 2·√(B·T). Below that tension the straight state stops being a minimum and the thread wraps on itself at a radius of 0.91 mm. That radius is 2B/M, which is 2/(r·ω) once the torque is written out: it depends on the twist and on the ratio of the two stiffnesses, and on neither stiffness itself.

A crepe is a yarn that will not lie still

A crepe cloth's pebbled surface is the yarn's own torque acting on a cloth that cannot resist it. The instability that makes a slack yarn snarl says how large the pebbles should be, and the answer is a millimetre — which is what a crepe looks like.

pattern · Variation What a raising machine can catch in a 2/2 twill. The draft with every weft float long enough for a raising wire to lift marked on it. The teeth need an unsupported length of thread on the surface, so a cloth in which every thread is bound at every crossing offers them nothing at all — which is why a napped fabric is always a twill or a satin and never a plain weave.

Raising moves the surface onto the hairs

A raising machine pulls fibre ends up out of the floats, and what a finger or a light then meets is not the cloth's surface at all but a layer of loose fibre standing above it. The criterion for which cloths can be raised is the same criterion, exactly, that decides which cloths have crown line — so raising spends the surface that would have made the fabric shine.

finishing · Nap What it takes to bury a cloth's crowns. The film needed to fill a fabric's surface to a stated level, for plain, 2/2 twill, satin 8 in sheeting, at a film density of 1.2 g/cm³. Burying the crowns entirely takes 187 g/m² on the plain, 186 g/m² on the 2/2 twill, 183 g/m² on the satin 8 — and the ordering is not the ordering of roughness. A weave with plateaux presents a wide flat top that a thin film covers, and a weave with points presents crowns with valleys between them that the film has to fill before it is continuous anywhere. Every gram spent filling a valley is a gram that is not bridging a hole, which is where a coated cloth fails.

A coating fills the crowns before it bridges the holes

A film does not sit on a cloth, it fills it — and the volume it has to supply to reach a level is the integral of one minus the bearing area. Burying an ordinary sheeting's crowns takes 185 grams a square metre, which is more than the cloth weighs, and the whole of the weave's influence is spent in the first ten of them.

finishing · Coating A round thread reflects a beam into a fan. A round thread seen end-on, with a beam arriving from straight above. Every point across the thread has its own normal, tilted by the angle it sits at, and mirrors the beam through twice that angle — so a single direction in becomes a whole fan out, spread across the thread and not at all along it. Seen from the front that fan is a highlight lying along the thread, exactly as long as the length of thread that is straight, which is the float. Nothing about this depends on the fibre. A cylinder of any material returns a fan, and the only way to narrow it is to stop the section being a cylinder — which is what a calender does.

A float reflects into a line

A cylinder cannot return a beam to a point. Its normals sweep the whole half-turn across it and nothing at all along it, so a straight thread throws light into a fan — seen as a highlight lying along the thread, exactly as long as the length of thread that is straight. The lobe of a satin is twice as narrow along the thread as across it; the lobe of a plain weave is exactly round.

weaves · Shine Two cloths touch on a fraction of what one cloth does. A 2/2 twill in sheeting pressed against a flat plate, and the same cloth pressed against another piece of itself. At an approach of 24.9 µm the single surface is touching 15.87% of the plan and the pair 3.130% — a factor of 5. The reason is that a gap between two rough surfaces is the sum of two depths, so both surfaces have to be near their own maxima at the same place, and the chance of that is the product of two small numbers. The pair's curve is the convolution of the two height distributions, computed exactly on histograms rather than fitted to a Gaussian — because a woven surface is bimodal and nothing about it is Gaussian.

Friction is two surfaces, not one

A gap between two rough bodies is the sum of two depths, so two cloths face to face touch on the convolution of their height distributions rather than on either of them. At the approach a light touch produces that is twenty times less contact than the same cloth against a plate — which is why a fabric's friction against a plate and against another fabric are two different measurements.

finishing · Friction The sett sets the pitch of the relief and not its height. A 2/2 twill in sheeting set from 14 to 29 ends per centimetre. The spacing of the crowns falls from 714 µm to 345 µm — in exact proportion to the sett, because it is the sett — while the height the surface swings through moves from 381 µm to 381 µm, which is not at all. The reason is the closure condition: the two crimp heights must add to the sum of the two diameters whatever the spacing, so the amplitude of the surface is pinned by the yarn and only its wavelength is free. The third curve is the root-mean-square roughness measured off the sampled surface, which wanders by a few per cent because it depends on where the sample grid falls relative to the crowns — it is drawn to show that it has no trend, not to be read off. A closer sett therefore makes a finer-grained cloth and not a smoother one, and the two are confused in every description of fabric handle. At 32 ends per centimetre the geometry refuses altogether: the cloth is close enough that its crimp can no longer divide equally, which is the jam arriving as a loss of symmetry rather than as a loss of room.

The sett owns the pitch and the yarn owns the height

Set a cloth twice as close and its surface does not get smoother. The crowns come twice as often, because that is what a sett is, and they stand at very nearly the same height, because the closure condition pins the amplitude to the yarn — so a fine cloth is finer-grained rather than flatter, and the two are confused in every description of handle.

setting · Sett A crepe's search has 4,416 winners and the surface separates them. All 5,040 rearrangements of the base this collection's crepe is built on, scored by how unevenly their crown line is spread over the repeat. 4,416 of them reach the correlation floor, which is the criterion the crepe was chosen by — so that criterion is not choosing, it is tying, and the search takes the first of a very large set. 28 of the rearrangements have a perfectly even surface, the bar at zero, and 16 of those are also at the correlation floor. The crepe actually drawn, marked, sits at 0.236 — the thirty-eighth percentile, better than most and not at the floor. The improvement is available, it costs nothing, and no criterion this collection had could see it.

A crepe is flat in its draft and not in its surface

A crepe weave is chosen by pushing the draft's correlations as flat as they will go. That criterion turns out to tie: on the base this collection uses, 4,416 of the 5,040 rearrangements reach the floor. Sixteen of them additionally spread their crown line perfectly evenly — and the crepe actually drawn is not one of the sixteen.

weaves · Texture weaves The bearing crowns of 2/2 twill and 2/2 hopsack, over 3 repeats. The cells at which the warp is on the face, drawn over 3 repeats of each draft — which is the surface a plate meets, since the other system is a step below it. 2/2 twill has 1 component in its repeat and a path that runs the whole way across the cloth, in both directions; 2/2 hopsack has 2 components in its repeat and no path across the cloth at all. Both carry the same length of crown line by the bearing count, and one is a ridge while the other is a field of islands. What the drawing cannot show is the depth of the gaps between them, which is the step to the second system and is a few micrometres.

Four drafts in five have no path along their own crowns

A 2/2 twill and a 2/2 hopsack carry exactly the same length of bearing crown line, which the surface census noted and could not explain. One of them is a ridge running diagonally across the cloth without a break; the other is a field of square islands with no path between them. Counted over the whole catalogue, 4,016 of 22,874 drafts have a crown path that reaches the far side, 1,616 have one in both directions, and 130 have crowns with no neighbour at all.

cloth · Surface

Named alongside it

The objects these essays reach for when they reach for this one.

Crown lineBearing curveCrown heightPlateauFloat lengthSpecular areaCloth thicknessReal contact areaCatalogueCensusClosure conditionCover factor

All concepts