Textile Structure
how cloth is put together
Concept

Shafts — where it appears

The frames a loom lifts, one lifting plan each, whose count is the number of distinct columns a draft has and whose loading the draft does not decide. A jacquard dispenses with them by giving every end its own hook, which is what makes a figure of arbitrary shape possible.

Named by 15 essays across 5 fields — each of them below, with the objects they name alongside it.

A 2/2 threading, run out to three widths. The same four shafts threaded for repeats of increasing width. The threading line runs up and back down; the harness never grows, and the number of ends it carries is bounded by the loom's width rather than by its shafts.

The harness does not grow

Nearly every account of a loom says the shaft count limits the repeat. It limits the repeat of a straight draw, and of nothing else — a reversed twill on ninety-six ends weaves on the same four shafts as the twill it was made from, and the ratio grows without bound.

fancy · Shafts The draft for herringbone, as a loom holds it. The herringbone written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it.

What a dobby stores

A pattern chain does not store picks. It stores lifts — the distinct sets of shafts a draft ever raises — and for most drafts worth weaving that number is very much smaller than the number of picks, which is the second half of the reason a wide repeat is affordable.

fancy · Shafts The draft for 8-end satin, as a loom holds it. The 8-end satin written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it.

A jacquard is every end its own shaft

The machine is usually described as the one that weaves anything. What it actually does is abolish one of the loom's two budgets and make the other proportional to the width of the repeat — which turns a constraint on the design's kind into a constraint on its size, and those are very different things to be short of.

fancy · Jacquard A stripe of a satin stripe on a plain ground. a satin stripe on a plain ground, written as one draft of 8 picks and 20 ends. Each band is generated from its own rule and the whole matrix is measured as one: 10 shafts, which is the number of distinct columns in the union of the two bands, against 8 if every column were shared and 10 if none were. The bands have 0 columns in common.

A stripe is a partition of the warp

A striped cloth is not a weave with decoration on it — it is one matrix in which different bands of ends obey different rules. The shaft count is a set union rather than a sum, and of forty-five pairs of standard weaves only three share a single column.

pattern · Stripe The draft for 2/2 twill, as a loom holds it. The 2/2 twill written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it.

How many shafts a draft needs

Every quantity this site has counted so far is a property of the cloth. This one is a property of the loom — the number of distinct columns in the matrix — and it is very probably the strongest single predictor of which of the twenty-two thousand four-by-four drafts anybody ever wove.

weaves · Shafts Heddles per shaft: stripe. The threading of a narrow satin stripe on a broad plain ground, over a warp of 1,200 ends. Each bar is one shaft and its length is the heddles on it. The draft needs 10 shafts however they are loaded; the heaviest carries 500 and the lightest 25, a factor of 20.0. Spending 20 shafts instead brings the heaviest down to 100.

Where the heddles go

A draft says how many shafts it needs and says nothing about how the ends divide between them. On a satin stripe over a plain ground the two ground shafts carry twenty times what the stripe shafts do — and the only cure is to spend shafts, which turns the threading into an allocation problem with an exact answer.

fancy · Shafts Everything the relative origin decides. Each of six quantities computed from a weave matrix, swept over all 64 relative origins of 8-end satin figured on 8-end sateen. A quantity that takes one value across the sweep is a gauge freedom of the pair; one that takes several is something a designer chooses without knowing it. longest float takes 2 values; interlacing rate takes 2 values; weft-face fraction takes 3 values. The origins fall into 3 different partitions, so the moving quantities are not all decided by the same number. What the table cannot show is the census over all 65,536 profiles, which is a seventh column, and the one that showed the origin decides whether the cloth holds together.

What else the relative origin decides

Where two weaves start relative to each other decides whether the cloth holds together, and it has a second consequence beside that. Two is what a search finds when it looks twice. Sweeping every origin against every measure of the cloth turns up a third — the longest float, which is the one property a weaver actually looks at — and turns up an earlier figure caption that says the opposite.

pattern · Blocks What a shed costs, in newtons. The tension the shed puts into one end at each shaft of a 24-shaft harness, for a 25 tex cotton yarn. The strain is set by the loom's geometry alone; the tension is that strain times the yarn's modulus. The front shaft holds 0.52 N and the back 1.95 N, which is 14 and 52 per cent of the yarn's breaking load. What the chart cannot show is the rest of the warp tension, which the let-off adds on top of all of these and which no geometry decides.

What the shed costs, in newtons

The shed's strain has been computed here and could not be priced: a strain is a length over a length and says nothing about how hard a thread is being pulled. A modulus turns it into a tension — and the back shaft of a twenty-four-shaft harness turns out to hold its ends at half their breaking load, all day, from the geometry alone.

mechanics · Yarn stiffness Plain weave, doubled. Plain weave, then the same weave with its picks grouped in 2, its ends grouped in 2, and both — which are a warp rib, a weft rib and a hopsack — and a 2/2 twill beside them for comparison. The rules under the drafts bracket the threads that lift together on every pick and so lie touching. Each doubling multiplies the cloth's own unit by 2: 2, then 4, then 8 intersections. The hopsack and the twill interlace equally often and are drawn from different rules. The setts under each draft are the densest that weave may be set at with a 0.25 mm yarn, and a rib's two are 0.750 apart where every other weave here is square.

A cord is a stripe with no colour in it

Warp rib, weft rib and hopsack are plain weave with its threads doubled, in the warp, the weft, or both. Six of the nine measures this site takes off a matrix cannot tell a 2/2 hopsack from a 2/2 twill, and the three that can are not the ones a weaver quotes.

weaves · Rib weaves Three places a mistake can be made, and three shapes it leaves. A loom holds a design in three separate objects, and a single mistake in each of them produces a fault of a completely different size — not because the mistakes differ, but because of how many intersections each object controls. On a 50 m piece of muslin 1500 mm wide, holding 396,000,000 intersections: one end drawn on the wrong shaft is wrong at every pick for the whole length, 110,000 of them; one pick made in the wrong shed is wrong across the whole width once, 3,600; and one shaft tied wrongly to one treadle is wrong wherever that shaft's ends meet that treadle's picks, which is everywhere — 6,187,500, or 1.6% of the cloth. The ratio between the extremes is 1719 to one, and the largest of the three is the one nobody sees happen, because every thread is exactly where it should be.

Three mistakes and the shape each one leaves

A loom holds a design in three separate objects, and one error in each of them is the same size of error. What they cost differs by a factor of seventeen hundred — and the largest of the three is the one nobody can see happening, because every thread is exactly where it should be.

fancy · Shafts How many layers the repeat, the harness and the beams each allow. Three ceilings on the number of layers a double cloth can have, for five layer weaves. The repeat's bound is half its ends and is a property of the notation. The harness's is the strain budget — 13 shafts on an ordinary broad loom at a 1.0% warp strain limit — divided by the shafts one layer of that weave costs. The beams' is how many warps the loom carries, which is 2. The shortest of each three is marked, and it is the beams at the coarse end of the table and the harness at the fine end; the repeat is never the binding one except at two-end layers, where it happens to coincide with the harness. A double cloth of eight-end satin layers needs 16 shafts and the budget is 13, so it is a jacquard construction by arithmetic rather than by choice. What the bars cannot show is the pick rate: a k-layer cloth needs k times the picks per centimetre of finished cloth and takes k times as long to weave, which is a cost rather than a ceiling and is the reason four-layer cloths are rare even where they are possible.

The repeat allows four layers and the loom allows two

A repeat of eight ends can hold four separable cloths, and the site has a witness that reaches the bound exactly. No loom weaves four. The harness's strain budget buys thirteen shafts and a layer costs its own weave's shaft count, so five-end satin layers stop at two and eight-end satin layers cannot be doubled on a dobby at all — and two differing layers already want a beam each. The notation's ceiling is the only one of the three that is never binding.

fancy · Double cloth Grouping the two systems by different amounts. Plain weave with its ends grouped by one number and its picks by another, over a grid of both. The four weaves the trade names are the corners of this space — plain at one and one, a warp rib down the first column, a weft rib along the first row, a hopsack on the diagonal — and the interior is the oblong matt, which has a name and no literature. Every cell weaves on two shafts, so the harness cannot tell any of them apart; the fundamental domain is exactly 2ab, so the notation's cost is the product; and the longest float is the larger of the two groupings. The two densest setts move with the two groupings separately, so the sett ratio is one exactly on the diagonal and nowhere else — a 3×1 matt sets at 1.50 and its transpose at the reciprocal. What the grid cannot show is the cord: the diagonal has no directional relief at all and everything off it does, in the direction of the larger grouping.

The four named weaves are corners of a family

Plain, warp rib, weft rib and hopsack are one construction with two knobs, and the trade turns both together or neither. Group the ends by two and the picks by three and the result is an ordinary cloth with a name, no literature and a fundamental domain of twelve intersections on two shafts — and the family's three quantities all have closed forms: two shafts everywhere, a unit of exactly 2ab, and a longest float of the larger grouping.

weaves · Rib weaves The draft for 2/2 twill, as a loom holds it. The 2/2 twill written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it.

A lifting plan says nothing without a threading

The second of the notations for something larger than a weave is a pair, not a notation: a threading and a lifting plan, and neither alone expresses anything. The pair's image is exactly the drafts with no more distinct columns than there are shafts — 98 at two shafts, 5,282 at three, all 22,874 at four — and it is not nested with the profile draft's in either direction. The profile reaches 192 drafts that need all four shafts, and misses 64 of the 98 a two-shaft loom weaves.

cloth · Notation The named colour-and-weave effects, sorted by the loom their weft needs. Each named colour-and-weave effect with the shortest band in its colour order and the cheapest loom that can throw that order in the weft, on a loom with 4 boxes a side. end-and-end, runs of 1 and 1, needs picking at will; hairline, runs of 1 and 1, needs picking at will; log cabin, runs of 1 and 1, needs picking at will; tattersall, runs of 1 and 9, needs picking at will; birdseye, runs of 2 and 2, needs boxes at one side; crow's foot, runs of 2 and 2, needs boxes at one side; step pattern, runs of 2 and 1, needs boxes at both sides; three-and-one, runs of 3 and 1, needs picking at will; houndstooth, runs of 4 and 4, needs boxes at one side; shepherd's check, runs of 6 and 6, needs boxes at one side; gun club, runs of 4 and 4 and 4 and 4, needs boxes at one side; glen check, runs of 4 and 4 and 4 and 4 and 2 and 2 and 2 and 2, needs boxes at one side. The warp costs nothing, because a colour order in the warp is laid out once at warping; the weft is thrown one pick at a time by shuttles that stay where they land, so an effect's price is its weft order alone. What the bars cannot show is the pattern, which is in neither the order nor the weave but in what they make of each other.

The finest colour-and-weave effects need the rarest loom

A houndstooth, a shepherd's check and a gun club check are thrown by the cheapest shuttle loom there is. A hairline, an end-and-end and a log cabin are thrown by none — a colour on every other pick is thrown from the same side every time, so its shuttles pile up at the far end of the loom and never come back. The dividing line is the parity of the bands and nothing else, which is why it survives the fact that no two sources agree about how wide a shepherd's check is.

pattern · Stripe A 2/2 twill with warp 1/1 and weft 2/2, as drawn and woven across. A 2/2 twill coloured 1/1 in the warp and 2/2 in the weft, drawn as the face of the cloth, and the same cloth turned through a right angle, which is what the loom makes if the two colour orders are exchanged and the weave turned with them. As drawn the weft order is 2/2 and needs boxes at one side; woven across the weft order is 1/1 and needs a loom picking at will. What the drawings cannot show is whether the cloth's two systems can be exchanged, which depends on their yarns and setts.

A colour-and-weave look costs its cheaper order

The finest colour-and-weave effects need the rarest loom because a weft order is thrown pick by pick and a warp order is laid out once, so an effect's price was said to be its weft. That is true of a construction and false of a cloth. The same cloth can be woven lying across the loom, with its warp order thrown as weft and its weft order laid in the warp, and then it costs the other order. Over every two-colour look twelve small weaves make with orders up to six threads — 4,036 of them — 55 per cent need a loom picking at will as drawn and 31 per cent need one either way round. The looks turning rescues are the ones fine in one direction only, and not one of the trade's named effects is among them.

pattern · Stripe

Named alongside it

The objects these essays reach for when they reach for this one.

HarnessThreadingCensusLifting planCloth integrityRepeatFloatJacquardPoint paperStripeCheckColour and weave

All concepts