Textile Structure
how cloth is put together
Concept

Interlock — where it appears

A double-faced knit in which two rib fabrics are interlaced, so both faces show only knit loops. It needs interlock gating on the machine, which is a needle alignment rather than a property of the structure, and this collection asserts that the result is one fabric.

Named by 11 essays across 2 fields — each of them below, with the objects they name alongside it.

1×1 rib — alternate wales to the back. A knitted fabric seen in section across the wales. Alternate wales pulled to the back fold the fabric like a concertina, so its relaxed width is a projection; pulling it wide unfolds the section and no yarn changes length while it happens.

Rib and interlock

A rib fabric is a plain knit folded like a concertina, and its enormous widthwise stretch is the fold opening out. Nothing in it is elastic, and the extension available is a cosine.

knits · Knit rib-float in section. A two-bed structure seen in section across the wales, over 3 repeats of course 1. The front bed's loops sit on the upper line and the back bed's on the lower one, offset by 0.5 of a needle pitch because the gating is rib. Of the 2 floats in the repeat, 2 lie in the gap between the beds and 0 on a surface. The upper panel is the fabric at the machine and the lower one is the same course with the beds closed up, which is what happens when the fabric is cast off — and neither panel is a relaxed fabric, because the loops are drawn as arches of one size and a real one settles wherever the yarn's bending leaves it.

A second bed changes what a float is

Every float so far has been on a surface, because every knit so far has had one needle bed. Put a bed behind it and the yarn runs in the gap between them — and over the whole enumeration of two-bed structures, 1,248 floats of 1,272 lie inside the cloth, on no surface at all.

knits · Two-bed tubular, as a graph of its wales. Every wale of tubular as a node — 2 on the front bed and 2 on the back — with one chain per course joining everything that course takes yarn on, because a course is one traverse of one yarn. The nodes are filled by which component they fall into. This structure comes out as 2 fabrics: F0+F1 and B0+B1. The same answer is obtained a second way, by walking every partition of the wales and asking whether any course straddles it, and the two are required to agree.

Does a double jersey hang together

Two beds knitting with nothing passing between them are two fabrics that happen to have been made at once. Of 6,561 two-bed arrays, 1,135 are fabrics and 50 of those are two fabrics — and 28 of the 50 split across the beds rather than along them, so neither half is a layer.

knits · Two-bed A knit's restoring force, and the column that does not move. A plain knit of 20 tex cotton at a loop length of 3.5 mm, over the extension range its own geometry admits. The bending energy stored in one loop is the same number at every extension — the loop's arcs are held to a radius by the thread they wrap rather than by the fabric's dimensions, so extending the fabric does not bend anything more. The frictional resistance at the interlocks is not zero: it is μ times the force pressing there, times 2.34 interlocks per millimetre of width. So a knit's resistance to extension is dissipative rather than elastic, which is why it does not spring back and why its dimensions depend on how much it has been agitated. What the rows cannot show is the interlock force itself, which this site does not have for a knit and which is recorded as missing.

What stops a knit extending

A knitted loop's bending energy does not change as the fabric extends — exactly, over the whole range its geometry admits. Something resists, and it is not stiffness. It is friction at the interlocks, which is dissipative rather than elastic, and that single fact accounts for why a knit does not spring back, why a softener changes its dimensions and why the constants its size is quoted with contain no yarn property at all.

knits · Knit Which knitted structures spiral, at a twist factor of 4.0. A yarn leaves the spinning frame with a torque it has not been allowed to release, and a loop knitted from it leans. The lean per unit of twist factor above balance is measured; what is counted here is the structure. A loop on the front bed and one on the back are mirror images, so their torques have opposite signs, and a fabric that knits equally on both beds nets to zero whatever the yarn is doing — which is why 1x1-rib, 2x2-rib, interlock do not spiral and plain, half-cardigan, tubular do. The count has to be made per fabric and not per structure: an interlock and a tube both knit equally on the two beds, and they are opposite cases, because an interlock's two components each straddle the beds while a tube's are each wholly on one. The integrity criterion, which asks what nothing holds together, is what tells them apart. What the bars cannot show is the tube's second face, which leans the other way.

A jersey leans because its yarn still turns

A single-jersey T-shirt comes back from the wash with its side seam spiralling round the body, and a rib does not. The difference is not the yarn: it is a count. Loops on opposite beds are mirror images, so their torques oppose, and a fabric that knits equally on both nets to zero whatever the yarn is doing.

knits · Spirality Why a cuff is ribbed. The force a knit pulls back with, over the range a cuff is used across. It rises the whole way — 0.79 N per metre at 23% to 3.38 at 104% — and it is small throughout, which is the combination a cuff needs and almost nothing else supplies. A rib gets its extension by geometry, folding alternate wales to opposite faces so that its relaxed width is about half its opened one, and it gets its recovery from the loop reconfiguring. Neither is the yarn stretching, which is why a cuff made of a fibre with no elastic recovery at all still works.

A rib pulls back on a force the loop supplies

A cuff has to give a great deal at almost no load and come back reliably, and no ordinary material does both. A rib gets its extension from folding, which is geometry, and its return from the loop reconfiguring, which is now a computable force — under four newtons a metre over the whole range a cuff works across.

knits · Two-bed A rib crosses a gap where a jersey crosses a diameter. A one-by-one rib in section across 5 wales, drawn at a bed gap of 3 yarn diameters — 0.501 mm — because the relaxed gap of a rib is a measurement this collection does not hold and every figure of one says what it was drawn at. Alternate wales sit on opposite beds, so every sinker loop between them travels the whole gap. In a jersey the same yarn climbs one diameter, 0.167 mm. That single difference takes the contact force from 38.30 mN at 11.7° out of the fabric to 72.51 mN at 16.2°, and the through-thickness part from 7.81 mN to 20.17 mN.

A rib climbs a gap

A jersey's yarn crosses one diameter between interlacings because that is what a crossing of two threads is. A rib's crosses the whole distance between the two beds. Nothing else in the model changes, and that one length is the whole mechanical difference between the fabrics.

knits · Two-bed How much of a fabric's yarn crosses between the beds. The share of half periods that cross from one bed to the other, read off each structure's own traverse rather than quoted. It is the mechanical difference between these fabrics in this account: a half period that crosses climbs the whole bed gap and one that does not climbs a yarn diameter. Single jersey and a tubular fabric come out at zero — the tubular one because its two faces are made on separate courses and never meet — and a one-by-one rib comes out at one, with every sinker loop crossing. A two-by-two rib is at a half, which is the number a reader would guess and is here counted.

Where a two-bed fabric's yarn is

Thirteen named structures, and for each of them the share of its yarn that crosses between the beds — read off its own traverse rather than quoted. It separates the fabrics into three groups, and one of the groups turns out not to be a fabric at all.

knits · Two-bed Which knitted fabrics lie flat, counted from the structure matrix. The curl balance of every named two-bed structure this site holds, with a tuck counted in full on the bed that took its yarn: the yarn a repeat puts on the front bed minus the yarn it puts on the back, over the total. A fabric lies flat exactly when it is zero, and the criterion has to put single jersey at one end and a one-by-one rib at the other or it is worth nothing — which it does, at 1.00 and 0.00. What it is for is the rest: a tubular fabric balances because it is two jerseys facing opposite ways, both cardigans balance because a tuck holds yarn on the bed that took it, and half-milano and a three-by-one rib come out front-heavy — which is what they are and what they do. 6 of the 13 structures curl.

Which knitted fabrics lie flat

Curl was explained here by counting face changes between courses, which works for stockinette and garter and reaches nothing else. The same question turns out to be a signed sum over a structure's own grid — and it answers for every fabric a two-bed machine can make, including the ones nobody has a rule for.

knits · Two-bed How much of a fabric's yarn crosses between the beds. The share of half periods that cross from one bed to the other, read off each structure's own traverse rather than quoted. It is the mechanical difference between these fabrics in this account: a half period that crosses climbs the whole bed gap and one that does not climbs a yarn diameter. Single jersey and a tubular fabric come out at zero — the tubular one because its two faces are made on separate courses and never meet — and a one-by-one rib comes out at one, with every sinker loop crossing. A two-by-two rib is at a half, which is the number a reader would guess and is here counted.

A tube and an interlock balance for different reasons

Two structures come out identically flat on a signed count and are as unalike as two knitted fabrics get. One is two jerseys that curl in opposite directions and are joined at the edges; the other is a fabric whose every course crosses. Telling them apart needs a different question asked of the same grid.

knits · Two-bed A rib crosses a gap where a jersey crosses a diameter. A one-by-one rib in section across 5 wales, drawn at a bed gap of 3 yarn diameters — 0.501 mm — because the relaxed gap of a rib is a measurement this collection does not hold and every figure of one says what it was drawn at. Alternate wales sit on opposite beds, so every sinker loop between them travels the whole gap. In a jersey the same yarn climbs one diameter, 0.167 mm. That single difference takes the contact force from 38.30 mN at 11.7° out of the fabric to 72.51 mN at 16.2°, and the through-thickness part from 7.81 mN to 20.17 mN.

A run cannot cross a bed

A dropped stitch unroves because its neighbour above can pull it out along a path that costs almost nothing. In a rib the neighbour above is on the other bed, and the path goes through the gap — so a run in a two-bed fabric has to pay for a climb before it can take a single loop.

applied · Damage

Named alongside it

The objects these essays reach for when they reach for this one.

RibNeedle bedTwo-bedCourseConnectivityCurlLoopWaleGatingMissCloth integrityContact force

All concepts