The collection

Every essay — page 24

Page 24 of 24, continuing through the fields in the same order.

What cloth is Weaves Setting and geometry Knits and other structures Mechanics and drape Pattern and colour Compound and figured cloths After the loom Cloth doing a job

FieldsSeriesThreadsWeave indexRefutationsConceptsSearch

Compound and figured cloths

Double cloth, pile, leno, and the loom that decides what can exist. Where a fabric stops being one binary matrix — a third thread system, a warp order that changes between picks — and where the integrity criterion runs out and friction takes over.

What a figured warp pays in tension to share one beam. For six pairings of figure and ground, the difference in warp tension that lets their ends share one beam: the force per end that takes the take-up difference out of the ground's crimp, along that region's own constant-length locus, with the yarn's rigidity at both ends of the band two tests place it in. a damask: satin on its own complement, 0.00% apart: none needed; an eight-end satin figure on a five-end satin ground, 0.31% apart: 0.006 to 0.020 N; a five-end satin figure on a 3/1 twill ground, 0.90% apart: 0.021 to 0.069 N; an eight-end satin figure on a 2/2 twill ground, 3.02% apart: 0.304 to 0.995 N; an eight-end satin figure on a plain ground, 14.15% apart: past what the ground's crimp can give; a 2/2 twill figure on a plain ground, 11.14% apart: past what the ground's crimp can give. The loom's front shaft holds 0.52 N an end. What the chart cannot show is how uneven a warp's tension may be before it shows in the cloth.

A figured warp pays in tension before it needs a beam

Figure and ground take up warp at different rates, and counted against a fixed slack, any difference at all — a third of a per cent — made a round figure need four beams. A real let-off holds tension, not length. Ends that consume more pull harder, and an end pulled harder gives up crimp, until every end consumes alike. For an eight-end satin figure on a five-end satin ground that costs a hundredth of a newton an end, and one beam serves. For a satin on plain it costs more crimp than the ground has, and no tension will do.

5 figures · Jacquard
The springs a leno easer can be. The stiffest spring, per end, that an easer can carry without any span of the crossing end rising above an ordinary end's working tension at any fraction of the crossed shed, against how far its preload sits above the warp's resting tension of 0.5 N. Behind the harness, where an easing bar acts, it is 1.1 N/m at a preload equal to the resting tension and falls to nothing by 15 per cent above it; in front of the harness it is 4.8 N/m. Everything under a curve works and nothing above it does. The window is a corner: a spring barely stiffer than a dead weight, with a preload matched to the warp's own tension. What the chart cannot show is the bar's mass, which the loom's speed makes matter and which the next views take up.

A leno easer should be a light weight

A spring easer gives length when the crossing end pulls, so it cannot give it too early, which was the fault in a cam driven off the shed. The question left was its rate. The answer is that it hardly has one. Behind the harness the easer feels the back span, and two gripping eyes keep that span within fifteen per cent of its resting tension while the kink carries its load. So the spring must hold its span almost constant over a sixty-eight-millimetre stroke: at most 1.1 newtons a metre per end, a dead weight in all but name. At speed the bar's own mass is what limits it, and it falls with the square of the loom's speed: 2.3 grams an end at a hundred picks a minute, 0.6 at two hundred.

6 figures · Leno
Which loose pieces in a cut tuft are free at once. A cut-pile tuft 12 mm tall on a 2 mm base, spun from a 90 mm staple, with a seeded sample of its fibre pieces drawn along the yarn and the tip's untwisted run-out, 5.6 mm, shaded down each leg. 22 pieces pass under the binding pick; of the 9 that lie wholly in one leg, 3 lie wholly inside the run-out, where the twist presses on nothing, and are free at once; the other 6 reach down into twisted yarn and are held until wear opens the twist further. What the drawing cannot show is the run-out's edge, which is a fall in pressure rather than a line.

A cut pile sheds in two stages

Every cut tuft of staple yarn holds loose fibre pieces that nothing anchors but the twist, and at the tip the twist holds nothing: it runs out over a length the grip arithmetic already gives, five and a half millimetres in a wool carpet yarn. A loose piece lying wholly inside that run-out is free the day the carpet is laid; one reaching below it is held until walking opens the tip's twist. So the reservoir drains in two stages, and the pile height decides the split. A velvet sheds everything it will ever shed at once. A twelve-millimetre wool carpet sheds a fifth of its reservoir at once and four fifths later. A shag sheds almost nothing at first and fourteen per cent of its fibre eventually.

5 figures · Pile
A disc woven on one beam, as it catches a lamp. A disc of 5-float satin on a ground of float 3, twelve blocks square, woven on one beam so that every column is pulled to the tension that makes it consume what the others do, and drawn as its blocks catch a lamp. A block is lit when its warp's crossings still reflect into the eye; outlined blocks are figure. At the mirror every block is lit. Tilted by 10.8° along the warp, the ground in the columns that carry most ground — the tightest — has gone dark, while the ground in line with the figure's widest part, pulled least, still shines: a band as wide as the figure runs down the ground above and below it. What the drawing cannot show is the diffuse light every block also returns, which dilutes the contrast and does not reverse it.

A figure woven on one beam shows its columns off the mirror

A figured warp shares one beam by letting the columns that want more yarn pull tighter until every column consumes alike. With the figure allowed to give crimp as well as the ground, the tightest column of a satin disc on a twill needs 0.013 to 0.042 newtons, under a tenth of the working tension. Its warp lies tens of micrometres lower, a relief too small to see. At the mirror it shines exactly as a slack column does. A few degrees off the mirror, along the warp, its crossings stop reflecting before a slack column's do, and the figure's own columns appear as bands in the ground. Only a damask has none.

6 figures · Jacquard
Where the weight on a shared leno easer comes to rest. The tension in the back span of each end of a leno pair — the length between its last heddle and the back rest, where an easing bar acts — at each fraction of the crossed shed, with one bar under both ends weighted at 1.0 N a pair, twice the warp's resting tension, so that it rests on its stop with the shed closed. The two back spans always sum to the weight. Closed, they share it equally. The partner, an ordinary end lying in the bottom of the shed, can take only 11 mm of the bar's travel before it goes slack, which it does at 37.5% of the opening; from there the crossing end's back span carries the whole 1.0 N. On a bar of its own, dashed, the same span stays at 0.50 N. What the chart cannot show is what the crossing end's other spans do with the extra tension, which the next views take up.

One weight under a leno pair ends on one end

A leno's crossing end wants about seventy millimetres eased to it at every crossed shed; its partner lies in the bottom of the shed as an ordinary end and wants none. One weighted bar under both is set where the closed shed shares its weight between them, but the partner can take only eleven millimetres before it hangs, and it is slack by three eighths of the shed. From there the crossing end carries the whole weight, twice the rest its own bar would hold it at, and its tightest span ends forty per cent over the working tension while the partner hangs thirteen centimetres behind the harness. No weight serves both, because a bar gives every end it carries one length.

6 figures · Leno
A leno partner lifted by its doup's loop. The tension in each span of a leno's partner end at the full crossed shed, against how far the doup's loop lifts it above its own straight line 6 mm in front of its heddle on the doup's shaft. The partner is then three spans: fell to loop, loop to heddle, heddle to back rest. With the loop clear it is an ordinary end, 1.07 N in its front span. At a 4 mm lift the front span carries 1.48 N, +38% on the untouched partner, the span between loop and heddle 1.26 and the back span 1.00; with nothing gripping, dotted, all three would carry 1.12. At 8 mm the front span reaches 1.90 N. What the chart cannot show is how far a real loop lifts its partner, which the doup's standard decides and which is swept here rather than computed.

A leno's slackener eases the partner, not the doup

In a bottom-doup leno the doup's loop passes beneath the partner, and if it lifts the partner on its way up it puts a second turn six millimetres in front of the partner's heddle. A four-millimetre lift bends the partner through 74 degrees in two places, and its front span goes from 1.07 newtons to 1.48 — a tenth of that from the bend and the rest from grip. The back span, which is all an easing bar can feel, does not move. A slackener that drops the doup's standard four millimetres clears the partner exactly, gives the crossing end six per cent of its easing, and costs the shuttle nothing.

7 figures · Leno
The partner's peak against how late a slackener starts. The largest tension the partner's front span reaches, against the share of the shed opened when the slackener starts to drop, at a 4 mm rise. It stays at 1.07 N for any start up to 0.748 of the shed, where the partner with no slackener passes that tension. Later than that, the peak is the touched tension at the moment it starts, up to 1.39 N at 0.95, against 1.48 N for no slackener at all.

A leno's slackener only has to arrive

A slackener that lets the doup down in step with the loop keeps a leno's partner clear at every moment of the shed, and it looked as though a real one would have to track that closely. It does not. A partner's tension only rises as the shed opens, so a slackener can leave its whole drop until three quarters of the way up and the peak does not move at all. Lateness is paid for elsewhere: starting later than 0.58 of the shed rubs the loop more than having no slackener, and above 234 picks a minute a falling weight cannot start as late as the partner would let it.

7 figures · Leno
A figure's streak in a room with a lamp and a window. A 5-float figure on a 3-float ground, on one beam: its slackest ground column over its tightest, in a room lit by a lamp placed in the window of tilts and a window sixteen degrees wide at the mirror, against the lamp's share of the light: a 1° lamp, 1.018 at 0.05, 1.042 at 0.1, 1.093 at 0.2, 1.256 at 0.5, 1.576 at 1; a 2° lamp, 1.006 at 0.05, 1.018 at 0.1, 1.044 at 0.2, 1.126 at 0.5, 1.288 at 1; a 4° lamp, 1.000 at 0.05, 1.006 at 0.1, 1.019 at 0.2, 1.061 at 0.5, 1.144 at 1. A dashed line marks a difference of two per cent, a usual figure for what can be seen between neighbouring areas. The figure cannot show the streak's own sharpness, which decides whether two per cent is seen.

A figure's streak needs a tenth of the room's light from one lamp

A figure woven on one beam pulls its columns to different tensions, and off the mirror the tight ones go dark first. Under a spotlight that is a streak of up to two to one. In a room the streak has to compete with whatever else is lit, and a window at the mirror sees the columns alike. The sum comes out simple: a two per cent difference needs a lamp carrying about five per cent of the light for each degree of its half-width, whichever figure and ground. Below that the streak is lost, and an overcast room hides it entirely.

6 figures · Jacquard
The lamp a figure's streak needs, against the width of its repeat. The share of a room's light that a lamp in the window of tilts must carry for a standard eye 2 m away to see the ground streak of a 5-float figure on a 3-float ground, framed by ground, against the width of the repeat. A 1° lamp: 1.3 per cent at 50 mm, 1.7 per cent at 100 mm, 2.7 per cent at 200 mm, 4.6 per cent at 400 mm, against 3.2 on a fixed two per cent rule (dashed), which it crosses near 253 mm. A 2° lamp: 2.5 per cent at 50 mm, 3.4 per cent at 100 mm, 5.3 per cent at 200 mm, 9.1 per cent at 400 mm, against 6.3 on a fixed two per cent rule (dashed), which it crosses near 253 mm. A 4° lamp: 5.0 per cent at 50 mm, 6.7 per cent at 100 mm, 10.4 per cent at 200 mm, 17.8 per cent at 400 mm, against 12.4 on a fixed two per cent rule (dashed), which it crosses near 254 mm. A narrow repeat shows its streak at less light than the fixed rule allows and a wide one needs more. The chart cannot show colour, or the matte light that dilutes every share.

A figure's streak is plainer from across the room

A figure woven on one beam leaves its ground a little brighter in the columns through the figure and a little darker in the columns beside it, and across a repeat that difference is very nearly one cosine. An eye is ten times less sensitive to a slow gradient than to a fine one, so whether the streak shows depends on how wide the repeat looks. From two metres a fixed two per cent threshold is right only for a repeat about 250 millimetres wide. A narrower one shows at less light, a wider one needs more, the same design woven finer shows its fault in dimmer rooms, and stepping back makes every streak plainer.

6 figures · Jacquard