Textile Structure
how cloth is put together
Concept

Hairiness — where it appears

The fibre ends and loops standing off a yarn's surface, which exist because the pressure holding a twisted assembly together falls to exactly zero at its edge. They give a yarn a contact diameter larger than the one its mass implies, and they are what a neighbouring thread, a finger or a friction test actually meets.

Named by 12 essays across 4 fields — each of them below, with the objects they name alongside it.

The two diameters of a 20 tex yarn. The pressure inside a twisted yarn is zero at its surface, so the outermost fibres are held by nothing but their own buried ends and some of them stand off as loops and ends. A yarn therefore has two diameters: a mass diameter of 167.1 µm, which is a volume divided by a length and is the one every other calculation on this site uses, and a contact diameter of 217.1 µm, which is what a neighbouring thread, a finger or an air stream meets. The gap is a hair layer of 25.0 µm on each side and it is measured, not computed — nothing here predicts hairiness. What is computed is the consequence, and it is 29.9% of the diameter every cover factor on this site was built from.

The hairs are what touch

The pressure inside a twisted yarn falls to exactly zero at its surface, so the outermost fibres are held by nothing and some of them stand off. A yarn therefore has two diameters — the one its mass gives and the one a neighbour meets — and only the first is in the arithmetic.

cloth · Hairiness The pressure a 30° twist puts on its own fibres. A twisted yarn squeezes itself. Every fibre under tension at a radius pulls inward with sin²θ of its tension per unit length, and integrating outward to the surface — where the pressure is zero by definition, because there is nothing outside to push against — gives p(r) = ½σ(cos²θ(r) − cos²α) in closed form. At a surface angle of 30° the pressure on the axis is 12.5 per cent of the core fibre's own axial stress and the mean over the section is 5.65 per cent of it. The shading is that closed form and the curve is the same function plotted; the shape is what matters, and its one uncompromising feature is the zero at the edge. The outermost fibres are held by nothing, which is why a yarn is hairy, why a surface fibre is the one that comes away on a finger, and why singeing changes a yarn's behaviour out of all proportion to the mass it removes.

A tuft is set so it cannot untwist

A cut pile tuft has a free end, and at a free end the pressure holding the twist is zero. So the twist runs out over a computable length, the tuft opens, and a carpet loses its appearance long before it loses any material.

fancy · Pile What it costs to touch a cloth. The pressure needed to bring a stated fraction of the plan into contact, for plain, 2/2 twill, satin 8 in sheeting. Reaching two per cent of the plan takes 2.83 kPa on a plain and 0.05 on a satin 8, a factor of 55. The stiffness in this figure is fitted and is labelled as such. A yarn's resistance to being squashed out of round has no lower bound at all — a bundle of fibres free to slide is a fluid in cross-section — so no bracket exists to compute this from, and what is used is the value this collection fitted to measured fabric thickness. Every curve moves together across its published range, which is why the ratio between weaves survives and the absolute values are quoted with the fit named.

How much of a cloth is touching

Press a fabric against a flat plate with the weight of a hand and ask what fraction of it is actually in contact. The bearing curve answers, and the answer is about four per cent — of which the great majority is not the cloth's surface at all, but the hairs standing off it, which nothing in this arithmetic can see.

cloth · Contact A 20 tex cotton yarn and the fibre standing off it. 6 mm of a 20 tex ring-spun cotton yarn with the hair population this site computes from the yarn's own count and staple — 0.89 hairs per millimetre, every one of them drawn. The two axes are at different scales and have to be — the yarn is 167 µm across and its hairs reach past a millimetre, so a picture at one scale is either a bare line or a black rectangle. Along the yarn is 99 pixels to the millimetre and off it is 74, a 1-fold exaggeration of the vertical. Lengths are drawn from the exponential the model predicts, mean 621 µm; the rules mark one, two and three millimetres with the count a hair-counting instrument reports at each, and the hairs crossing each rule in the drawing are the ones those counts are about. At the yarn's own surface the long hairs cover 1.1% of the space beside it, which is why the picture is mostly gap. Nothing here is the short population, which carries most of the protruding length and none of the reach; and a hair reaching past the room the canvas has is drawn to the edge of it, so the very longest few are shortened in the drawing and not in the arithmetic.

A yarn's surface is a distribution

This collection has computed where a cloth stops, and every one of those numbers is a statement about yarn. What a finger, a plate, a droplet or a ray of light actually meets first is a population of fibre ends standing off the yarn — and it is a population, with a count and a length, rather than a layer with a thickness.

cloth · Hair layer The two diameters of a 20 tex yarn. The pressure inside a twisted yarn is zero at its surface, so the outermost fibres are held by nothing but their own buried ends and some of them stand off as loops and ends. A yarn therefore has two diameters: a mass diameter of 167.1 µm, which is a volume divided by a length and is the one every other calculation on this site uses, and a contact diameter of 217.1 µm, which is what a neighbouring thread, a finger or an air stream meets. The gap is a hair layer of 25.0 µm on each side and it is measured, not computed — nothing here predicts hairiness. What is computed is the consequence, and it is 29.9% of the diameter every cover factor on this site was built from.

Singeing is the cheapest change to a surface

Pass a cloth through a flame fast enough and it loses under one per cent of its mass. What it loses is the part of itself that was doing most of the touching, and lustre, friction, printability, pilling and measured cover all move at once.

finishing · Hairiness A yarn's diameter is a contour, not a length. The fraction of the space beside a 20 tex cotton yarn that is occupied by hair, against height, grossed up from the modelled population by the measured split between the long and short populations. At the yarn's own surface it is 8.9% — the layer is almost entirely gap — and it falls away exponentially from there. Every instrument that reports a yarn diameter is picking a contour of this curve, and the contours are far apart: a threshold that needs half the space filled is never met at all, one that needs a twentieth is met at 355 µm, and a hair counter triggers out at 2353 µm. The earlier model gave the layer a single thickness of 25 µm, which is a fair description of where most of the material is and wrong about its extent by more than a decade. What the curve cannot say is which contour any particular instrument uses, which is a fact about the instrument.

A yarn has a diameter for every instrument

Conservation of volume gives a yarn one diameter and every other route gives a different one. The disagreement is not experimental scatter: a yarn's outside is a coverage that falls away exponentially, and each instrument stops at whatever contour of it will trigger the instrument.

cloth · Hair layer What a raising machine can catch in a 2/2 twill. The draft with every weft float long enough for a raising wire to lift marked on it. The teeth need an unsupported length of thread on the surface, so a cloth in which every thread is bound at every crossing offers them nothing at all — which is why a napped fabric is always a twill or a satin and never a plain weave.

Raising moves the surface onto the hairs

A raising machine pulls fibre ends up out of the floats, and what a finger or a light then meets is not the cloth's surface at all but a layer of loose fibre standing above it. The criterion for which cloths can be raised is the same criterion, exactly, that decides which cloths have crown line — so raising spends the surface that would have made the fabric shine.

finishing · Nap One hairiness reading does not fix the other. Every yarn on this curve has exactly the same total protruding fibre length — the quantity an integrating hairiness meter reports — and they differ in how that length is distributed. The count of hairs at least three millimetres long runs from 170 to 4354 per hundred metres, a factor of 26, across decay lengths real yarns actually have. The two instruments read two functionals of one population: the first moment N₀λ and the tail N₀e^(−3/λ). A correlation between them can exist only if λ is fixed across the yarns being compared, and λ is a fibre property, so it is not. That is the whole of why the trade's two hairiness numbers have never agreed, and it is arithmetic rather than instrumentation. What the figure cannot show is which of the two predicts anything: the tail does, because pilling, prickle and a printed edge all need reach.

Two hairiness meters read two moments

The trade has two instruments for yarn hairiness and thirty years of failing to predict either from the other. They are not measuring the same thing badly. One reports the first moment of a distribution and the other reports a tail probability, and two functionals of one curve are related only through a parameter neither of them reports.

cloth · Hair layer A hair layer is a balance, so singeing does not stay done. The hair population of a 20 tex cotton yarn under rubbing, started from a singed cloth and from an unusually fuzzy one. Abrasion does two opposite things: it frees ends that spinning left buried, from a supply of 2.23 per millimetre in the surface shell, and it removes hairs that are long enough to be caught. Where the two meet is a fixed point at 1.43 per millimetre, and the cloth goes there from either side with the same time constant — 248 cycles to halve the distance, whichever direction it is travelling. A singeing is therefore undone in a few hundred rubs, because the flame changed the stock and not the balance. What is predicted here is that a fixed point exists, that it does not remember the starting state, and that one rate serves both directions; where it sits relative to the spun level needs two rates the model does not supply, and it is set to reproduce the one thing everyone has noticed, which is that fabrics get fuzzier as they are worn.

A hair layer is a balance, not a stock

Singeing takes under one per cent of a cloth's mass and changes its lustre, its friction, its printability and its pilling. It also does not stay done, because rubbing frees fibre ends as fast as it breaks them off, and a flame changes the stock while leaving the balance exactly where it was.

finishing · Hairiness The force at an interlacing, which no longer lies in the fabric. A crossing of a relaxed jersey in section on the left, with the thickness expanded 3×, and on the right the contact force drawn at the angle the solve gives it — which is a true angle, unlike anything in the section beside it. The head of one course and the feet of the next lie one yarn diameter apart through the fabric, 0.167 mm, so the interlacing is not a point in a plane and the force at it is not in one either. It comes out at 38.30 mN a stitch, turned 11.75° out of the fabric: 37.50 mN along the wales, which is what friction has to hold, and 7.81 mN through the thickness, which is what holds the two faces apart. Divided by the area a stitch occupies the second is 15.1 kPa, or 113 mmHg — a pressure, and the quantity a compression measurement reports.

What a thickness gauge reads on a knit

The structure says two yarn diameters and the gauge says more, and the gap is not an error in either. A gauge lands on the highest crowns, through a canopy of protruding fibre, under a load that has already begun to compress both — and it does that on a surface that is nothing but crowns.

cloth · Contact Compacting a spinning triangle moves one instrument and not the other. What happens to each hairiness reading when a 20 tex cotton yarn is spun compact instead of ring, as a percentage of the ring value. The total falls by 8% and the long hairs by 65%, a ratio of 8.3. The asymmetry is a prediction rather than a fit. Compaction removes ends that were unbound over a long stretch of the spinning triangle, which is the long population and nothing else; the short population is untouched, and it carries about 88% of the length the integrating instrument is adding up. So the instrument that sees everything barely moves and the one that sees only the tail collapses. The model under-states the fall in the total, because compaction certainly does something to the short population too and nothing here models it — the direction of that error is stated and it is the conservative one.

The spinning triangle decides the hair

A ring frame converges a flat ribbon of fibres to a round yarn, and for the length of that convergence the fibres at the ribbon's edges are held by nothing. Everything a spinner can do about hairiness is done in that triangle, and the two hairiness instruments respond to it by wildly different amounts.

setting · Twist Which knitted structures present a float a raising wire could catch. Each of the named two-bed structures, with how many of its floats lie exposed on a face rather than inside the cloth. A plain jersey has no float at all; the ribs and the cardigans have none; the interlocks and milanos have floats and every one of them is interior, closed over by the other fabric. a single jersey with a float and a three-by-one rib with a float present an exposed float, on the back. So the criterion that decides which woven cloths can be napped decides the same question here and answers it for 2 of 13. What the bars cannot show is the hair layer, which a wire also catches and which no float census can see.

A jersey has no float for a wire to catch

Only a float can be raised, and the four-by-four census answers which woven cloths qualify: two. Asked of a knit the same question needs this collection's knitted float rather than a draft's, and the answer is that a plain jersey has no float at all — not a short one, none — while the ribs and cardigans have none either and the interlocks and milanos have floats every one of which is interior. Of 1,135 two-bed structures a machine could make, twenty present a float a wire could hook, and not one of them presents it on both faces.

finishing · Nap

Named alongside it

The objects these essays reach for when they reach for this one.

Hair layerEscape fractionProtrusion lengthSpecificationStaple lengthCover factorFrictionMeasurementYarn diameterBearing curveCloth thicknessContact pressure

All concepts