Textile Structure
how cloth is put together
Concept

Damask — where it appears

A figured cloth in which figure and ground are the same satin used two ways, one warp-faced and one weft-faced. Being its own complement is what lets one warp and one weft carry two tones, and a shading is what happens between them.

Named by 14 essays across 3 fields — each of them below, with the objects they name alongside it.

Figure and ground on 8 ends. A damask is a satin and its own complement. The figure is warp-face and the ground is weft-face, they carry the same longest float and need the same shafts on the same threading, and the whole of the pattern is carried by which system is on top.

A damask is its own complement

The pattern is carried by direction alone. Figure and ground are the same satin, one warp-face and one weft-face, with the same longest float, the same shaft count and the same threading — so the cloth's most famous effect costs it no structural difference whatever between the two areas.

fancy · Jacquard 8-end satin figured on 8-end sateen. A 3 by 3 block profile, drawn above at one square per block, and the cloth it produces below at one square per intersection. The figure weave is 8-end satin and the ground is 8-end sateen, both single cloths on their own; each block is 8 ends and 8 picks. The composite is 1 cloth, with a longest float of 8 and 0 threads lying loose, all counted from the matrix that drew the picture.

A figure is not a stripe

Two sound weaves side by side always make sound cloth — that is a theorem, and it was proved here. Put one of them inside a *region* instead of a band and it stops being true, and whether it is true or not turns out to depend on a number that appears nowhere in either draft: where the two weaves start relative to each other.

pattern · Blocks What a figure costs in shafts. Two families of block designs in 8-end satin on 8-end sateen at blocks of 8. One repeats three block-columns however wide it gets and costs 24 shafts at every width from 24 to 120 ends. The other gives every block-column a different pattern and costs 16, 24, 32, 40, 48 shafts as it grows — exactly 8 more per new column. Shafts are counted as distinct columns of the composite matrix.

What a figure costs the loom

A block design's shaft count does not depend on how wide the figure is, or how deep, or how many blocks it has. It depends on how many *different* block-columns it has, and each new one costs exactly one repeat of the ground weave — 8 shafts, then 16, then 24, in a straight line with no slope to fit.

pattern · Blocks The staircase a woven outline is. Four straight edges on a block grid, stepping 1 across in 1, 1 across in 2, 2 across in 1, 1 across in 4. Each tread is one repeat of 8-end satin, which at 24 by 22 threads per centimetre is 3.33 mm across and 3.64 mm up. A jacquard hook at 140 cm width is 1.17 mm, so the machine resolves 2.9 times finer than the cloth can use.

A woven outline is a staircase

A jacquard's resolution is quoted as its hook count, and on a 1,200-hook machine 140 cm wide that is a step of 1.17 mm. The cloth cannot use it. A figure's smallest feature is one repeat of the ground weave, which on an eight-end satin is 3.33 mm — so the machine resolves nearly three times finer than the fabric can hold, and a finer machine buys nothing at all.

pattern · Blocks Flexes per end in the same check, ground a pick along. One bar per warp end above the draft of the same check, ground a pick along, each the number of times that end changes sides in one repeat — which is the number of times the shed drags it through its heddle eye. The counts run from 6 to 10, and they are the same numbers that give the cloth its interlacing rate of 0.500 per intersection.

A figure is harder on its warp

Every basic weave flexes all its ends exactly as often as each other — plain, twill, satin and sateen alike, and it is a one-line theorem. Figure one of them on another and that evenness goes, or does not, depending on where the ground weave was started relative to the figure. The same invisible offset that decides whether a fine figure holds together decides, at a coarse one, how unevenly the loom works the warp.

mechanics · Shed The step between a figure and its ground. Three figures on a plain ground, all in one sheeting's threads at its own setts. A thread presses on the thread it crosses only where it turns, and it turns at its interlacings — so the pressing a region receives per unit area is the contact force at one turn times the turns per unit area, and the second factor is a property of the matrix exactly. A five-end satin turns two fifths as often as a plain weave, is pressed two fifths as hard, flattens less, and stands 55 µm proud of it. What the rows cannot show is that both regions are given a plain weave's weave angle: a satin's crimp is genuinely smaller and its turns genuinely gentler, so the real step is larger than this, by an amount not computed here.

A figured cloth has a step in its surface

A damask is one cloth in one set of threads at one sett, and it is not flat. A thread presses on the thread it crosses only where it turns, so a region that turns less often is pressed less often, flattens less and stands thicker — and the step is a ratio of interlacing rates, read off the matrix with no yarn property in it.

pattern · Blocks A spread shading on 8 ends. The 7 tone steps of a spread shading on an 8-end repeat, each built by adding one more coset of the 8-end satin with move 3. Every coset has exactly one mark in every end and every pick, so the fraction of warp on the face is k over 8 exactly at every step, with no averaging in it. The numbers beneath are the longest float, and they run 7, 3, 3, 1, 3, 3, 7 — so the lustre scale is not the tone scale. The midtone is a plain weave and the extremes are satins, which is why a spread shading is at its most matt exactly in the middle. What the drafts cannot show is the surface: a long float stands proud of a short one, so an evenly toned shading is not an even surface either.

A shading changes two things at once

The tone steps of a shaded damask are exactly even — each adds one satin coset, so the fraction of warp on the face is k over n with no averaging in it. The lustre steps are not even at all: on eight ends the longest float runs 7, 3, 3, 1, 3, 3, 7, so a series that grades smoothly in tone is at its most matt exactly in the middle.

pattern · Shading A damask's figure and ground trade places when the cloth is turned. A satin 8 figure on a sateen 8 ground in sheeting — one cloth, one set of threads, one sett, and the ground is the figure's own complement. Their total specular areas are within a few per cent of one another, so neither is intrinsically the brighter. What differs is the direction: the figure's crowns run with the warp and the ground's with the weft. So the contrast between them is 2.0-to-one with the light coming from 8° and 0.47-to-one from 90° — it reverses, exactly, a quarter turn apart. That is what makes a damask visible in one colour, and it is not the step in its surface: the step is fifty micrometres and returns no light at all under a diffuse illumination, while this contrast is a factor of 2.0 and is present whenever there is a direction in the light.

A figure shows by its shine, not its step

A damask is one cloth in one colour and its pattern is plainly visible. This collection attributed that to the step in its surface — fifty micrometres of relief, computed from the interlacing rates. The step is real and returns almost no light. What makes the figure visible is that its crowns run at right angles to the ground's, so the two trade places when the cloth is turned.

pattern · Blocks The surface of an 8-end shading. The height of the cloth's own surface at each tone of an 8-end shading, for the two chains, on a sheeting at 0.50 N in the end. A thread presses on the thread it crosses only where it turns, so a region that turns more often is pressed more often and finishes thinner — and firmness rises towards the midtone of a shading. The spread chain therefore sinks 84 µm between its ends and its midtone and the consecutive chain 43 µm, with 2 of its steps at exactly one thickness against the spread chain's 0. The tone scale is level by construction and the surface under it is not. What the plot cannot show is the light: a step in the surface reads as a line under a raking beam whatever the tone is doing, which is why a relief nobody specified is visible at all.

A tone ramp is a valley, and the satin digs it

A shading's tone is exact and its lustre is measured; its thickness is neither, and nobody specifies it. A firmer weave is pressed harder at every crossing and finishes thinner, so an eight-end shading sinks eighty-four micrometres between its ends and its midtone — about a third of the cloth's whole thickness, on every cloth tried. Build the same chain on a twill instead of a satin and the sag is exactly nothing.

pattern · Shading One tone of an 8-end cell, arranged three ways. The same 32 marks in the same 8 × 8 cell, placed three ways, with the number of marks in each end printed beneath it. On the left the clustered dot a halftone screen makes: 4 of its threads carry every mark or none, so they never leave a face, and the criterion reports 16 separable layers rather than one cloth. In the middle a cloth built from the tone step by moving 2 marks sideways within their own picks — every pick still carries 4, the ends run 3 to 5, and that difference is a warp stripe of 25.0% contrast the design did not draw. On the right the tone step: every end and every pick at exactly 4. What the drawing cannot show is how visible the middle one's stripe is, which depends on the sett and on the viewing distance and is not computed here.

A weave is a halftone screen with n greys

An eight-by-eight cell of dots gives a printer sixty-five levels of grey. The same cell in cloth gives seven. Sixteen of the missing fifty-eight go to the requirement that every thread reach both faces and forty-two go to the requirement that every thread carry the same number of marks — so evenness, not interlacing, is what a weave pays for its tone scale.

pattern · Shading The warp floats across a tone edge on 8 ends. 2 strips of point paper, each one repeat of a tone on either side of a straight edge between picks, with the edge ruled and every warp float of the greatest length that crosses it drawn along its thread. Ground the exact complement: tones of 7 and 1 marks per end (cosets 1 to 7 against coset 0), not nested, and the longest warp float across the edge is 8 against 7 inside either tone. Ground one pick along: tones of 1 and 7 marks per end (coset 1 against cosets 1 to 7), nested, and the longest warp float across the edge is 7 against 7 inside either tone. A float drawn in the warning colour is longer than anything either tone has on its own. What the strips cannot show is the cloth: the edge here is one intersection wide, and in a woven piece the two tones take up yarn differently, so the change is spread over threads that point paper draws as belonging wholly to one side or the other.

A damask's edge floats further than its figure

Figure and ground in a damask carry the same longest float, which is true of both areas and false along the line between them. A float can cross the edge where two tones meet, and when one tone's marks lie inside the other's it can never be longer than a float either tone already has. A damask built as an exact complement is the one place in n that its ground can start which breaks this, and it floats n picks at its edge against n − 1 inside.

pattern · Shading An 8-end weft-faced satin through a point tie on an end. The 8-end satin on a move of 3, weft-faced, woven through a point tie of 12 hooks that turns on a single end, so 22 ends carry one repeat. The strip above is the tie, hook number against end. Inside the satin the weft floats 7 ends; across the turn it floats 13, outlined, because on some pick the nearest interlacing is 7 ends away on both sides. What the drawing cannot show is how a long float at one line down the cloth behaves in use, which depends on the yarn and the finish rather than on the count.

A point tie nearly doubles the float at the turn

A point tie halves the hooks a symmetrical figure needs by driving every hook's end twice, out and back. It mirrors the ground as well, and a satin is symmetrical about no end: across the turn its weft floats 2n − 3 ends, or 2n − 2 between ends, at every hook count and wherever the satin starts. At eight ends that is thirteen or fourteen against seven — and the turn's other promise, more repeats that fit the width, is not kept either.

fancy · Jacquard What each figure-and-ground pairing costs in differential take-up. For each pairing of a figure weave with a ground weave, the difference between the two regions' warp crimps and the length of figure that difference allows before an end goes slack, taking the loom to absorb 1.2 millimetres. a damask: satin on its own complement: 0.00 per cent apart, no bound; an eight-end satin figure on a five-end satin ground: 0.31 per cent apart, a figure up to 392 millimetres; a five-end satin figure on a 3/1 twill ground: 0.90 per cent apart, a figure up to 133 millimetres; an eight-end satin figure on a 2/2 twill ground: 3.02 per cent apart, a figure up to 40 millimetres; an eight-end satin figure on a plain ground: 14.15 per cent apart, a figure up to 8 millimetres; a 2/2 twill figure on a plain ground: 11.14 per cent apart, a figure up to 11 millimetres. A damask's two regions are the same satin used two ways, so complementation leaves both float lengths where they were and the crimps are identical rather than close. What the bars cannot show is the slack, which is an input and which every length is proportional to.

A damask is the only figure that costs its beam nothing

Figure and ground consume warp at different rates, and the difference accumulates down the length of the figure. An eight-end satin figure on a plain ground puts its two regions fourteen per cent apart, which on a loom absorbing a millimetre of slack bounds the figure at eight and a half millimetres. A damask's two regions are the same satin used two ways, so complementation leaves both float lengths where they were — and their crimps are identical rather than close, to the last bit of a double.

fancy · Jacquard The beams a disc 12 blocks across needs, column by column. A disc 12 blocks across, 12 blocks by 12, figure shaded, with the beam feeding each column of ends written above it, for a figure floating 8 on a ground floating 1, whose warp crimps are 14.15 per cent apart, at 4 mm blocks over a 100 m piece with 1.2 mm of slack. It has 4 distinct columns and 4 distinct shares of the repeat in figure, and needs 4 beams. What the grid cannot show is the cloth's own crimp interchange, which would move tension between the columns instead.

A figured warp needs a beam for every share of its figure

Figure and ground take up warp at different rates, so a figured cloth on one beam is bounded in how long its figure may run, and a second beam is the obvious escape. It escapes only for ends that live wholly in one region. An end that crosses the figure for part of the repeat consumes warp at its own rate, and two ends can share a beam only if they spend the same share of the repeat in the figure and never drift a slack apart inside it. So a round figure twelve blocks across needs four beams, ninety-six blocks across needs twenty-nine, and any crimp difference at all — a third of a per cent will do — costs every one of them over a piece.

fancy · Jacquard

Named alongside it

The objects these essays reach for when they reach for this one.

Figure and groundFloatJacquardSatinBlock figureRepeatShadingToneProfile draftRelative originBlockCloth thickness

All concepts