Textile Structure
how cloth is put together
Concept

Heddle — where it appears

The eye a warp end passes through, carried on a shaft, which raises or lowers that end at every pick. How many sit on each shaft is decided by the threading rather than by the draft, and levelling them is a real optimisation with a real answer.

Named by 5 essays across 3 fields — each of them below, with the objects they name alongside it.

A stripe of a satin stripe on a plain ground. a satin stripe on a plain ground, written as one draft of 8 picks and 20 ends. Each band is generated from its own rule and the whole matrix is measured as one: 10 shafts, which is the number of distinct columns in the union of the two bands, against 8 if every column were shared and 10 if none were. The bands have 0 columns in common.

A stripe is a partition of the warp

A striped cloth is not a weave with decoration on it — it is one matrix in which different bands of ends obey different rules. The shaft count is a set union rather than a sum, and of forty-five pairs of standard weaves only three share a single column.

pattern · Stripe The shed in section. A warp line 1200 mm from the fell of the cloth at the left to the back rest at the right, with 8 shafts at 300 mm and every 16 mm behind it. Each shaft lifts its ends in proportion to its own distance from the fell, which is what gives the same 30 mm clear opening at the reed from every shaft. The resulting extension is 0.460 per cent at the front shaft and 0.722 per cent at the back, a ratio of 1.57. Vertical scale exaggerated 4 times.

The shed is an extension

Every model of a finished cloth treats a thread as inextensible, and every one of them is about a fabric that has left the loom. On the loom the warp is stretched thousands of times a minute by the shed itself, and the amount is exact trigonometry with nothing fitted in it: the square of the shed's tangent, times the shaft's own distance from the fell, over twice what is left behind it.

mechanics · Shed The strain across a harness. The warp strain each shaft of a 24-shaft harness puts into its own ends, from 0.460 per cent at the front to 1.728 per cent at the back. Shafts within a budget of 1.0 per cent are drawn in one colour and those outside it in another; the budget is reached at shaft 13.

The back shaft works hardest

How hard the loom is on a warp end is the product of two numbers from different worlds — how often its column changes sides, which is a property of a binary matrix with no millimetre in it, and the strain of the shaft it happens to be on, which is a property of a machine with no weave in it. Neither knows about the other, and the threading that joins them is a decision nobody makes on structural grounds.

mechanics · Shed Flexes per end in the same check, ground a pick along. One bar per warp end above the draft of the same check, ground a pick along, each the number of times that end changes sides in one repeat — which is the number of times the shed drags it through its heddle eye. The counts run from 6 to 10, and they are the same numbers that give the cloth its interlacing rate of 0.500 per intersection.

A figure is harder on its warp

Every basic weave flexes all its ends exactly as often as each other — plain, twill, satin and sateen alike, and it is a one-line theorem. Figure one of them on another and that evenness goes, or does not, depending on where the ground weave was started relative to the figure. The same invisible offset that decides whether a fine figure holds together decides, at a coarse one, how unevenly the loom works the warp.

mechanics · Shed Heddles per shaft: stripe. The threading of a narrow satin stripe on a broad plain ground, over a warp of 1,200 ends. Each bar is one shaft and its length is the heddles on it. The draft needs 10 shafts however they are loaded; the heaviest carries 500 and the lightest 25, a factor of 20.0. Spending 20 shafts instead brings the heaviest down to 100.

Where the heddles go

A draft says how many shafts it needs and says nothing about how the ends divide between them. On a satin stripe over a plain ground the two ground shafts carry twenty times what the stripe shafts do — and the only cure is to spend shafts, which turns the threading into an allocation problem with an exact answer.

fancy · Shafts

Named alongside it

The objects these essays reach for when they reach for this one.

LoomShedThreadingWarp strainCensusHarnessInterlacingShaftShaftsShift-ruleAbrasionAllocation

All concepts