Textile Structure
how cloth is put together
Concept

Contraction — where it appears

How much narrower cloth is than the reed that made it, which is exactly the weft's crimp over one plus itself. It is a geometric identity rather than a measurement, which is why the reed's pitch and the cloth's sett can never be the same number.

Named by 5 essays across 2 fields — each of them below, with the objects they name alongside it.

The reed is not the sett. Twelve ends held at the reed's pitch above and at the cloth's pitch below, for a sheeting whose weft crimp is 14.61 per cent. The count is the same in both rows and only the spacing changes: the cloth is 12.75 per cent narrower, so a reed at 24.43 ends per centimetre produces a cloth at 28. The crimp comes from the Peirce solution at this cloth's quoted construction.

The reed is not the sett

A reed holds the warp at a pitch, and the cloth that leaves it is narrower — by exactly the weft's crimp, with nothing fitted and nothing approximated. On a close balanced sheeting that is 12.75 per cent, on an open scrim 1.87, and a weaver who allowed one figure for both would be wrong by a factor of nearly seven.

setting · Take-up What the two setts can be set to. Two rules on one scale from 8 to 40 threads per centimetre. The upper carries the 49 warp setts a metric reed catalogue reaches at one to four ends per dent; the lower carries the 4825 pick densities a change-wheel take-up reaches. The mean spacing is 0.656 threads per centimetre in the warp and 0.0066 in the weft, a ratio of 99. The widest gap in the reed's range is 2.10 threads per centimetre.

The setts a loom can reach

Transposing a draft gives a perfectly good draft, and every count this site takes off a matrix either is symmetric under exchanging warp and weft or has a mirror twin. The loom is not symmetric at all: over the range ordinary cloth is woven in, it can choose a pick density 99 times more finely than a warp sett — and the warp sett cannot be changed once the warp is drawn in, at any granularity whatever.

setting · Take-up A 40-by-40 motif on a poplin, drawn and finished. A motif 40 ends wide and 40 picks tall, at the setts the reed and the take-up were set to, and the same motif measured on the finished cloth. Point paper has one cell per end and per pick, so a motif's proportions are the ratio of the two setts — and both setts move in the finishing, in opposite directions. On the poplin the aspect changes by a factor of 0.8429, so a circle drawn as a circle at the loom's numbers comes back 15.7% out of round and a designer who wants a circle must draw an ellipse of 1.1863. What the drawing cannot show is that the correction is not a property of the design: it belongs to the cloth, so the same card woven on a different construction is a different shape.

A motif is drawn at the wrong shape on purpose

Point paper has one cell per end and per pick, so a design's proportions on the cloth are the ratio of the two setts. Both setts move in the finishing and they move in opposite directions, so a circle drawn as a circle comes back out of round — by three per cent on a balanced cloth and by sixteen on a warp-dense one.

pattern · Pattern Selectable against reachable. How far up the take-up gear's catalogue a beat-up force reaches, on a sheeting. The catalogue holds 4,825 distinct pick densities between 8 and 40 per centimetre, which is the previous rung's count of what the machine can select. At 200 N per metre only 548 of them can be woven; at 2,000 it is 4,256. The fineness of the choice is untouched by the ceiling and the top of the range is cut off entirely, so the weft direction's advantage is resolution rather than reach. What the chart cannot show is the loom's own force, which depends on the beat-up mechanism and is not a property of the cloth.

A pick density is a force budget

The take-up ladder counted what a change-wheel take-up can select: 4,825 distinct pick densities between eight and forty threads per centimetre, against forty-nine warp setts a reed catalogue offers over the same range. That count assumed every setting is available. A beat-up force says otherwise, and cuts the top off the range without touching the fineness of the choice.

setting · Beat-up How far each cloth's sett moves between the loom and the finished state. A cloth on the loom is held: the warp is under beam tension and the picks are driven up at whatever density the take-up says. Let it go and it relaxes to the least-energy state of its own locus, which is a state at a different sett. The bars are how far each sett moves, and they always move in opposite directions because there is one locus: warp ends per centimetre fall as the cloth widens and picks per centimetre rise as it shortens. Seven of the eight move a little over one per cent; the poplin, whose two counts and two setts are the only unbalanced pair in the table, moves six and ten. What the bars cannot show is what a designer does with them, which is that the two numbers a specification quotes are not two free numbers — the finished construction is a point on a one-dimensional curve.

The construction a loom must be set to

A specification quotes ends and picks per centimetre in the finished cloth, and a loom is set to neither of them. The cloth relaxes to the least-energy state of its own locus, which is a state at a different sett — and because the locus is one curve, the two numbers a specification quotes are not two free numbers.

setting · Take-up

Named alongside it

The objects these essays reach for when they reach for this one.

SettTake-upReedLoomDentingRelaxationTensile locusAspect ratioBalanceBeamBeam tensionBeat-up

All concepts