Twist — the series · Textile Structure

Z twist at 800 turns per metre. A 20 tex cotton yarn, 0.167 mm across, with its surface fibres drawn as the helices they are. The angle between a surface fibre and the yarn's axis is 22.8°, and it is the only quantity in this family: the yarn is 4.1% shorter than the fibre in it and carries 85% of the strength the same fibre would give lying straight.

Twist is one angle

Every model on this site treats a yarn as a cylinder with a diameter. It is a bundle of loose fibres, and what makes it behave like a cylinder is twist — which is a helix, so the whole subject is one angle, and the trade's twist factor turns out to be the only combination of count and turns that decides anything.

part 1 · setting

Z twill, Z twist. A square of cloth with two directions on it. The broad lines are the twill, whose angle 45.0° from the warp comes from the setts alone — 24 ends and 24 picks per centimetre. The fine lines are the surface fibres of the warp ends, at 25.3° from the warp because the yarn is twisted 900 turns per metre. Between them is 19.7°, and that is the whole of the rule.

Twist and the twill line

The oldest rule of thumb in weaving says to weave a Z twill from S-twist warp for a bold line and from Z-twist warp for a subdued one. Both halves of it are geometry: the twill's angle comes from the two setts, the fibres' angle comes from the twist factor, and the rule is their difference.

part 2 · setting

Both halves of the twist curve, at 28 mm staple. The falling curve is obliquity and is exact — the affine end of the bracket, computed from the helix and nothing else. The rising curve is cohesion and is the half this collection had declined: a fibre end is gripped by friction under the twist's own radial pressure, the fibre's strength and the yarn's load cancel out of the comparison, and what is left is a critical length that depends on the twist through a pure function of the angle. Their product has a maximum at a twist factor of 3101 — 693 turns per metre at 20 tex, a surface angle of 20° — which is inside the range spinners use. The scale of the rising curve is fitted, through a contact efficiency of 0.05, and moving it moves the optimum; what it cannot move is the ordering between two staples or two fibres, which is what the two claims made from this figure are about.

The other half of the twist curve

This collection computed the falling half of the strength–twist curve exactly and declined the rising half as being out of reach. It is not out of reach. With the grip derived rather than assumed, the optimum comes out at a twist factor — and the same twist factor at every count, which is why the trade quotes twist factors at all.

part 3 · setting

Compacting a spinning triangle moves one instrument and not the other. What happens to each hairiness reading when a 20 tex cotton yarn is spun compact instead of ring, as a percentage of the ring value. The total falls by 8% and the long hairs by 65%, a ratio of 8.3. The asymmetry is a prediction rather than a fit. Compaction removes ends that were unbound over a long stretch of the spinning triangle, which is the long population and nothing else; the short population is untouched, and it carries about 88% of the length the integrating instrument is adding up. So the instrument that sees everything barely moves and the one that sees only the tail collapses. The model under-states the fall in the total, because compaction certainly does something to the short population too and nothing here models it — the direction of that error is stated and it is the conservative one.

The spinning triangle decides the hair

A ring frame converges a flat ribbon of fibres to a round yarn, and for the length of that convergence the fibres at the ribbon's edges are held by nothing. Everything a spinner can do about hairiness is done in that triangle, and the two hairiness instruments respond to it by wildly different amounts.

part 4 · setting

A slack twisted yarn takes a coil of one size. A 20 tex cotton at 800 turns a metre. Its own torque is 1.177 µN·mm at the free bound, and a rod under tension T is stable while its torque stays under 2·√(B·T). Below that tension the straight state stops being a minimum and the thread wraps on itself at a radius of 1.59 mm. That radius is 2B/M, which is 2/(r·ω) once the torque is written out: it depends on the twist and on the ratio of the two stiffnesses, and on neither stiffness itself.

Why a slack yarn snarls

Let go of a twisted thread and it wraps on itself. That is not the yarn being badly behaved: it is a buckling, it has a criterion, and the criterion turns a nuisance into an instrument for measuring the one constant this collection cannot pin down.

part 5 · setting

How much of a yarn has to hang before it stops snarling. The tension a 20 tex cotton needs to stay straight, at each twist level, expressed as the length of the yarn's own weight that would supply it. The two curves are the two ends of the stiffness bracket: the fibres free to slide, and the section coherent. At 800 turns a metre they are 1.9 metres and 616. Anybody who has let go of a twisted yarn knows which of those is right, which makes this one of very few places where the bracket can be closed from the everyday end. Both rise as the square of the twist, because the torque does and the criterion is quadratic in it.

How much yarn has to hang

The tension a thread needs to stay straight, converted into the only unit anybody has an intuition for: the length of the yarn's own weight. One bound says two metres and the other says six hundred, and everybody who has handled thread already knows which.

part 6 · setting

A snarl comes in one size

The radius a twisted thread coils to is twice its bending rigidity over its torque. Write the torque out and the bending rigidity cancels completely, leaving a number that depends on the twist and on the ratio of two stiffnesses — and on nothing else about the yarn at all.

part 7 · setting

What a high-twist yarn costs a cloth

Twist buys strength up to a point and then loses it, and everything else it does is a cost. A crepe twist is chosen knowing that, and the trade's twist limits are a balance among five quantities that this collection can now put beside one another.

part 8 · setting