Textile Structure
how cloth is put together
Series

Float — the series

10 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. Where the floats are in the 5-end satin. Every longest run of warp on the face, marked. A float is smooth because nothing interrupts it, which is the same reason it snags: there is a length of thread lying on the surface with nothing holding it down.

    The float decides

    How far a thread runs on the face before it goes under is one number, and it sits behind lustre, drape, snagging, abrasion, tear strength and how densely the cloth can be set. Almost nothing else in the subject has that reach.

    part 1 · weaves
  2. The highlights of a 8-end satin, move 3. Every unbroken run of warp on the face, drawn as the band of light it returns. A yarn is a cylinder and a cylinder reflects a line rather than a point, so a float's highlight is as long as the float — and how long that is, in inches, is the float divided by the picks per inch the weave can be set to.

    Why satin shines

    Lustre is usually filed under fibre, and silk gets the credit. It is a property of the weave: a cylinder reflects a line rather than a point, so the highlight a cloth returns is exactly as long as its longest float.

    part 2 · weaves
  3. What one cut costs. The length of thread set loose by a single abrasion cut through a warp float, with each weave measured at the densest setting that weave allows in the same yarn. The bars are inches of freed thread; the note beside each is the float in picks and the setting that float permits.

    Floats and abrasion

    A satin is said to wear badly. It does not wear quickly — its flat face spreads the rubbing over more thread than a plain weave's crowns do. What it does is fail badly, and those are different quantities moving in opposite directions.

    part 3 · weaves
  4. What the geometry says about a tear. A slit in a woven cloth, with the ends ahead of the tip gathered into the group that will break together. How many can gather is the opening divided by the slack in each gap, and the slack is the thread spacing less the thread diameter — an expression with no weave in it at all.

    Does a loose weave tear better

    The trade says a twill tears stronger than a plain weave of the same yarn, because fewer interlacings let the threads group. The geometry of that grouping has no weave in it at all — and where the geometry does speak, it predicts the opposite.

    part 4 · weaves
  5. What a float limit of 4 leaves. For each repeat, the fraction of the distinct twills on it whose longest float is within the limit. The constraint is usually stated as a rule about a drawing; it is really a statement about how much of the catalogue exists, and the catalogue shrinks as the repeat grows.

    Designing to a float limit

    Every jacquard designer works to a rule of the form nothing longer than four. It reads as a constraint on a drawing. It is really a statement about how much of the catalogue exists, and the catalogue shrinks as the repeat grows.

    part 5 · weaves
  6. single float as an array. One cell per needle per course, over 2 repeats each way. K knits a new loop and casts the old one off, T tucks the yarn into the loop below without casting off, M misses the needle and floats past it. The margins carry the two conditions: a wale with no K in it never casts off, and a course with no K in it is never caught by anything. Both hold here.

    The float in a knit

    Five rungs of this anchor have taken the float to be a length of thread on the surface with nothing holding it down. A knit has one too, and it behaves the same way in the light and the opposite way in the hand — because a woven float lengthens its thread and a knitted one shortens its fabric.

    part 6 · knits
  7. A 3-pick fold across a 8-end satin, move 3. A 8-end satin, move 3 on point paper with a fold 3 picks wide drawn across it at pick 3. A warp end's crimp is made where it turns from over to under, and the dots mark the turns that fall inside the fold. Averaged over the ends there are 0.75 of them, and 4 of the 8 ends in the repeat have none at all — those ends are marked with a line, and each of them crosses the fold dead straight with no crimp to give up. Over every fold position, 50.0% of end-and-place pairs are like that. What the drawing cannot show is what happens to those ends instead, which is that the whole of the fold's length difference goes into their fibres.

    How sharply a weave lets a cloth fold

    A fold's length difference is paid for out of crimp, and crimp is not spread evenly along a thread — it is made at the interlacings and nowhere else. So what a fold has to spend is not the weave's average crimp but whatever is inside the few picks the fold crosses, and in an eight-end satin half the warp ends have nothing there at all.

    part 6 · weaves
  8. The crossover length in four weaves. The gripped length at which a pick of a sheeting breaks rather than slides, in four weaves at a friction coefficient of 0.30. It is a millimetre or two for a plain weave and 8.0 mm for an eight-end satin, which is what a cut edge of each does. The interlacing rate appears in the answer only as a factor outside the logarithm, so the ratios between the four are exactly the ratios of their interlacing rates — in this model and in the sum of independent contacts alike. The rung below expected the float correction to change that ordering; it does not. It changes the size, by a factor of 3.7. What the rows cannot show is that all four use one cloth's crimp, so a satin's genuinely gentler turns are not in them.

    A float presses on nothing

    The rung below expected the float correction to change how a satin's hold compares with a plain weave's, by something like the ratio of their interlacing rates. It does not change the comparison at all — the interlacing rate leaves the answer outside the logarithm and divides straight out of any ratio. What it changes is the absolute answer, by a factor of four, for every weave alike.

    part 7 · weaves
  9. A slot and a square of the same area do not pass the same air. A hole of 62500 square micrometres, drawn out from a square to a slot twenty times longer than it is wide, at constant area throughout. The open area is unchanged by construction and the flow is not: it falls to 39 per cent of the square's. Two things move the same way and neither is a correction to the other — the hydraulic diameter falls as the rectangle is drawn out, and the shape factor rises from 14.23 for a square towards 24 for an infinitely thin slit, which is Shah and London's result quoted rather than derived. This is why a weave's float matters to what it passes even where its cover does not: a float lays parallel threads side by side and the hole beside it is a slot.

    A satin's hole is a slot

    Two cloths at the same cover have the same open area, exactly, and do not pass the same air. A float lays parallel threads side by side and the hole beside them is long rather than square, and drawing a hole out at constant area cuts what it passes to two fifths — because the hydraulic diameter falls and the shape factor climbs, and both of them move the same way.

    part 9 · weaves
  10. The float a point fault gives a weave, over every draft there is. Every four-by-four draft that describes one cloth — 22,730 of them — laid out as 8 ends by 8 picks, with each intersection of its repeat reversed in turn and the longest float that produces kept. There are two answers and no others. 90 drafts hold the fault to a float of 3; 22,640 — 99.6% of every weave there is — hand it a float of 7. The mechanism behind the second number is that a reversal at a binding point joins the two floats on either side of it, so a weave with runs separated by single binding intersections gives a single mistake the sum of two of its own floats. The 90 that escape are the drafts whose floats are short and evenly spaced — the plain weave and the ribs — which is not the class of weave the trade recommends for hiding a fault.

    Which weave hides a fault

    The trade says a busy weave hides a mistake. Every four-by-four draft there is was laid out as cloth and given every wrong lift it could have, and ninety-nine in a hundred hand that single mistake a float of seven — because a reversal does not lengthen a float, it joins two.

    part 10 · weaves

All series