Textile Structure
how cloth is put together
Series

Contact — the series

21 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. The force at a crossing. One warp end of a sheeting riding over three picks, with the weave angle Peirce's geometry solves for at that construction: 36.8°. An end held at 0.50 N presses each pick it crosses with 0.599 N, which is twice the tension times the sine of the angle and has no material constant in it. What the drawing cannot show is the relaxed case: a cloth with no tension in it still holds its threads together, and what does the holding then is the yarn's own resistance to being bent, which needs an elastica this site does not have.

    Every crossing is a force

    A thread arrives at a crossing at an angle and leaves at its negative, so the two pulls have transverse parts that add. The force pressing one thread onto another is twice the tension times the sine of the weave angle — and for an ordinary sheeting that is more than the tension in the thread itself.

    part 1 · cloth
  2. Where a thread stops sliding and starts breaking. A pick of sheeting gripped over a length of cloth, drawn one crossing at a time. The resistance is 0.30 times the 0.599 N each crossing presses with, so it rises with the length held; the breaking load of 3.74 N does not. The two are equal at 7.4 mm. What the drawing cannot show is that μ is a range rather than a constant, so the mark is a band and its position is exactly inversely proportional to the friction.

    A thread is held one crossing at a time

    Grip a thread over a length of cloth and its resistance to being pulled out rises with that length, because it is held at every crossing it makes. Its own breaking load does not rise at all. The two curves cross, and the length at which they cross turns out to be a seam allowance, a frayed edge and a tuft's anchorage — three rules of thumb with one number under them.

    part 2 · cloth
  3. A thread withdrawn from a plain weave and from a satin. One pick of a sheeting being pulled from 1.60 mm of cloth, in a plain weave and in a five-end satin, at a friction coefficient of 0.30. The drawn width of each thread is the tension in it at that point, to a common scale; the faint rules are where the thread actually turns, which is at its interlacings and nowhere else. A plain weave turns 2.80 times per millimetre and a satin 1.12, so the plain weave's tension compounds 2.78-fold over this length against the satin's 1.46. What the drawing cannot show is that the wrap angle is taken from a plain-weave geometry in both panels: a satin's crimp is genuinely smaller, so its real turns are gentler than these and its grip weaker still.

    A thread is gripped where it turns

    The arithmetic this site has used for fraying, seam slippage and tuft anchorage counts every crossing a thread makes as a grip and adds them up. A thread lying flat on the surface of a satin presses on nothing at all, and a thread that is gripped is gripped by a friction that compounds along its length rather than adding. Both corrections were recorded as missing and both are here.

    part 3 · cloth
  4. What it costs to touch a cloth. The pressure needed to bring a stated fraction of the plan into contact, for plain, 2/2 twill, satin 8 in sheeting. Reaching two per cent of the plan takes 2.83 kPa on a plain and 0.05 on a satin 8, a factor of 55. The stiffness in this figure is fitted and is labelled as such. A yarn's resistance to being squashed out of round has no lower bound at all — a bundle of fibres free to slide is a fluid in cross-section — so no bracket exists to compute this from, and what is used is the value this collection fitted to measured fabric thickness. Every curve moves together across its published range, which is why the ratio between weaves survives and the absolute values are quoted with the fit named.

    How much of a cloth is touching

    Press a fabric against a flat plate with the weight of a hand and ask what fraction of it is actually in contact. The bearing curve answers, and the answer is about four per cent — of which the great majority is not the cloth's surface at all, but the hairs standing off it, which nothing in this arithmetic can see.

    part 4 · cloth
  5. The presser foot sinks 1.8 µm into a 2/2 twill. A thickness gauge presses a flat foot onto the cloth at 1 kPa and reads the gap. It does not read the geometric thickness. The foot sinks until the area it is touching can carry the load, and that is 2.57% of the plan at a depth of 1.8 µm — so a 2/2 twill in sheeting whose outside stands 381.6 µm apart measures 379.8 µm. How far the foot sinks is a property of the draft, because the bearing area near the top is, and a weave with plateaux stops the foot in a fraction of the distance a plain weave lets it travel. The transverse stiffness used here is fitted to measured fabric thickness rather than predicted: across its published range the reading moves between 377.0 µm and 380.6 µm.

    A thickness gauge reads the draft

    A presser foot does not stop at the top of a cloth. It sinks until the area it is touching can carry the load, and how far that is depends on the shape of the bearing curve near the top — which is a property of the weave. So there is a weave term inside a measurement nobody thinks of as a weave measurement, and it is worth about one per cent.

    part 5 · cloth
  6. At 0.1 kilopascals the plate is standing on hair. A flat foot pressed onto sheeting at 0.1 kPa, over 3 mm of cloth. It stops 25 µm above the cloth's own crowns, because that is where the hairs it is bending can carry the load: of the 10 hairs drawn, 9 reach higher than the foot and are laid over under it, and the rest are untouched. The vertical scale is set by the approach and not by the layer — 5188 pixels to the millimetre off the cloth against 192 along it — because the foot's height above the crowns is tens of micrometres and the layer it stands in is more than a millimetre, so a picture at one scale shows the second and not the first. The thickness reported is 0.432 mm against 0.382 mm for the cloth itself, so 12% of the reading is a population and not a fabric. The hair layer carries up to 0.23 kPa before the foot reaches the crowns at all. A laid-over hair is drawn as two straight segments where a real one is an elastica: the corner is a convenience and the height it turns at is the measurement. What the picture cannot show is that a bent hair leans on its neighbours, which the arithmetic behind it does not know either.

    A light touch never reaches the crowns

    This collection found that a plain weave touches at points and every other cloth touches along lines, and that the difference is an exponent rather than a factor. It is a real result about a real surface, and at the pressures a fabric is actually touched at, nothing ever reaches that surface.

    part 6 · cloth
  7. The force at an interlacing, which no longer lies in the fabric. A crossing of a relaxed jersey in section on the left, with the thickness expanded 3×, and on the right the contact force drawn at the angle the solve gives it — which is a true angle, unlike anything in the section beside it. The head of one course and the feet of the next lie one yarn diameter apart through the fabric, 0.167 mm, so the interlacing is not a point in a plane and the force at it is not in one either. It comes out at 38.30 mN a stitch, turned 11.75° out of the fabric: 37.50 mN along the wales, which is what friction has to hold, and 7.81 mN through the thickness, which is what holds the two faces apart. Divided by the area a stitch occupies the second is 15.1 kPa, or 113 mmHg — a pressure, and the quantity a compression measurement reports.

    What a thickness gauge reads on a knit

    The structure says two yarn diameters and the gauge says more, and the gap is not an error in either. A gauge lands on the highest crowns, through a canopy of protruding fibre, under a load that has already begun to compress both — and it does that on a surface that is nothing but crowns.

    part 7 · cloth
  8. The contact force turns as the climb grows. The two components of the contact force against the climb, for a 20 tex cotton jersey at a 3.5 mm loop. The force along the wales is what friction has to hold and the force through the thickness is what holds the fabric open, and the second is bought at the expense of the first. At a jersey's own climb of one diameter they are 37.50 mN and 7.81 mN; at four diameters, which is a rib on an open gap, they are 22.39 mN and 18.61 mN. The friction balance is the ratio: friction has the whole force to work with and only the along-the-wales part to hold, so the coefficient a relaxed knit would need falls from a half to 0.490.

    Every fabric's thread lies in a plane

    A woven thread's crimp wave lies in a plane at right angles to the cloth. A knitted loop lies in a plane twelve degrees off it. Both halves of this collection turn out to be one picture with one angle in it, and the angle decides how much of a fabric's contact force acts through its thickness.

    part 8 · cloth
  9. Two courses at the yarn's own width, and the place they overlap. The solved course of a 20 tex cotton jersey at a 3.5 mm loop, drawn in plan with the course below it, each strand at the yarn's own diameter of 0.167 mm. Where the two overlap, the fabric is occupying the same space twice. The interlacing is where the model placed them one diameter apart. The closest they come is 0.130 mm — 0.780 of a diameter — and it is not at the interlacing. A round yarn cannot occupy this arrangement; a yarn flattened to 78% of its round diameter can, and flattened is what a yarn in a fabric measurably is.

    The fabric that does not fit

    Every solve in this collection minimises an energy over a centre line, and a centre line has no thickness. Nobody had checked whether the fabric that comes out of it can be built. It cannot: two adjacent courses of the relaxed jersey approach to four fifths of a yarn diameter, so the yarn passes through itself, at rest, everywhere.

    part 9 · knits
  10. The section the fabric asks for, beside the one the model drew. A 20 tex cotton yarn in cross-section, at 900 times life size. The circle is what every solve in this collection has assumed: a diameter of 0.167 mm from the count and the packing factor. The ellipse has the same area and a minor axis of 78% of it, which is the closest the fabric's own adjacent courses come to one another — 0.130 mm. Nothing about that number was fitted to a fabric. It falls out of a solve that knew nothing about flattening, and it lands inside the range the trade reports for yarn in cloth, which this collection has carried as a free parameter ever since it first put a number on a sett.

    The flattening nobody fitted

    A yarn in cloth is not round, everybody knows it, and nothing has ever predicted how flat. This collection's own knitted geometry turns out to require a flattening of four fifths — from a solve that knew nothing about flattening, made no allowance for it, and would have been written the same way if the idea had never occurred to anybody.

    part 10 · knits
  11. The flattening a knitted fabric asks for, against its own tightness. Every point is a solved fabric — 18 of them, over five loop lengths, three relaxation states and three counts — and the vertical axis is the closest its adjacent courses come, in diameters. The values run from 0.707 to 0.839 and they fall on one curve against the tightness factor, which is the model's only dimensionless group. That is what makes this a structural requirement rather than an arithmetical accident of one example: a tighter fabric demands a flatter yarn, by an amount its own tightness decides, and nothing about the fibre or the count enters except through that group.

    A flattening that follows the tightness factor

    Eighteen solved fabrics — five loop lengths, three relaxation states, three counts — and the flattening each one's geometry demands falls on a single curve against one dimensionless group. Nothing about the fibre or the count survives except through that group, which is what turns an arithmetical result into a structural requirement.

    part 11 · knits
  12. What flattening costs, against what the loop's bending is worth. The energy of squashing a 20 tex cotton to the 78% the fabric's geometry demands, as a multiple of the whole bending energy of one stitch, at three lateral rigidities. The free bound is exactly zero: a bundle of fibres free to slide resists a change of shape at constant area not at all, so flattening is free and the bracket on it has no floor. The coherent bound is 36 times the loop's bending, so a yarn that could not rearrange could not be knitted into this fabric at all. The fabric flattens, so it is reading the free end — which is the fourth ordinary observation on this site to land at that end of the bracket.

    Flattening is free and impossible

    The fabric demands a flattening and the yarn has to supply it. At one end of this collection's oldest bracket the deformation costs exactly nothing; at the other it costs thirty-six times the whole bending energy of a stitch. The fabric flattens — which is the fourth everyday observation in one phase to land at the same end.

    part 12 · mechanics
  13. Two courses as centre lines, and their closest approach. The solved course of a 20 tex cotton jersey at a 3.5 mm loop, drawn in plan with the course below it, as centre lines, with the closest approach marked. The interlacing is where the model placed them one diameter apart. The closest they come is 0.130 mm — 0.780 of a diameter — and it is not at the interlacing. A round yarn cannot occupy this arrangement; a yarn flattened to 78% of its round diameter can, and flattened is what a yarn in a fabric measurably is.

    The closest approach is not the crossing

    Two wavy curves that touch at a point are not necessarily closest at that point. Whether they are depends on one thing: whether they run alongside one another or cross. That distinction decides which of this collection's two fabrics fits together and which does not.

    part 13 · cloth
  14. A yarn is pressed on part of its length and free on the rest. The distance from each point of one course to the nearest point of the course below, for a 20 tex cotton jersey at a 3.5 mm loop, along two wales. It runs from 0.780 diameters at the worst to 3.81 at the freest, and 20% of the length is inside one diameter of its neighbour. The line at one diameter is where a round yarn would begin to overlap. What the profile says is that a single flattening ratio is an average: the section a yarn takes changes along its own length, which every racetrack section this collection has drawn assumes it does not.

    Where a yarn is thinnest

    A yarn in a fabric is pressed where it crosses and free where it does not, so its section changes along its own length. Every flattening this collection has ever quoted is a single number for a profile that runs from four fifths of a diameter to nearly four.

    part 13 · cloth
  15. Two courses at the yarn's own width, and the place they overlap. The solved course of a 20 tex cotton jersey at a 3.5 mm loop, drawn in plan with the course below it, each strand at the yarn's own diameter of 0.167 mm. Where the two overlap, the fabric is occupying the same space twice. The interlacing is where the model placed them one diameter apart. The closest they come is 0.130 mm — 0.780 of a diameter — and it is not at the interlacing. A round yarn cannot occupy this arrangement; a yarn flattened to 78% of its round diameter can, and flattened is what a yarn in a fabric measurably is.

    A loop bends at twice its own radius

    A rod of radius r cannot be bent to a centre-line radius below r without occupying its own space. A knitted loop's tightest bend is at 2.04 yarn radii — twice the hard limit, and falling as the fabric tightens. That is a ceiling on how tight a knit can be, from contact alone.

    part 14 · knits
  16. What flattening a section does to the ratio of the two stiffnesses. C/B is 2G/E for a circular section, because a circle's polar second moment is exactly twice its flexural one. A flattened section has two different flexural moments — easy about the long axis, hard about the short one — and the polar moment is still their sum, which is the perpendicular axis theorem and holds for any section whatever. So a flattened thread has three constants rather than two, and the multiplier on C/B depends on which way it is being bent. At the 0.78 a knitted fabric's own geometry demands, the easy direction multiplies the ratio by 1.322 and the hard one by 0.804. A knitted loop bends in the easy direction, so the collection's headline ratio is a lower bound for a yarn in cloth.

    The section that changes both stiffnesses

    A thread's two rigidities are in the ratio 2G/E, and that is a fact about a circular section: a circle's polar second moment is exactly twice its flexural one. A yarn in cloth is not circular, so a yarn in cloth has three constants rather than two — and the ratio a whole ladder rests on is a lower bound.

    part 14 · mechanics
  17. A knot, and the tension falling through it. A 20 tex cotton thread wrapped through 1 turn at a bend radius of 1 yarn diameters, with a coefficient of friction of 0.30. The wrap is drawn as a spiral because a thread taken round a pin comes back beside itself rather than onto itself. The marks round it are the fraction of the entry tension still there: 100%, 69%, 47%, 32%, 22%, 15%. The bend has already spent 3.6% of strain at the outside of the thread before any of that happens, against a breaking strain of 6.6%. So the largest total is at the entry, before the knot has done any gripping at all — which is where a knot in a real yarn is observed to break, and why a knot's efficiency is a property of its first bend rather than of the knot.

    A knot is nothing but contact

    A knot has no fastening in it. Nothing is glued, hooked, sewn or threaded through a hole: a thread is bent round itself until the friction where it presses on itself is more than the load. That makes a knot the purest contact problem in the subject, and the place to look first for what contact does.

    part 15 · applied
  18. The crest, and the loop that ought to be holding it open. One course of the solved fabric in plan, with the two half periods that meet at a crest marked. They approach to 0.003 mm — 0.018 of a yarn diameter — and run within that of one another for more than a millimetre of arc. The ring drawn between them is the needle loop of the next course, which is what holds them apart in a fabric and what this model does not have: the interlacing was declared a point, and a point holds nothing open. The same omission is what makes the course's writhe zero and its linking number zero, so three of this collection's findings are one defect seen three ways.

    What holds a crest apart

    Two half periods meet at every crest of every course and, in this collection's model, run within a fiftieth of a yarn diameter of one another for more than a millimetre. In a fabric what holds them apart is the loop of the next course drawn between them — which is the loop this model does not have.

    part 15 · knits
  19. A woven cloth asked the same question, and the answer is nearly one. The closest approach two crossing threads make, for four cloths from an open voile to a dense duck, in units of the separation they have where they touch. A value of one means the closest approach is exactly at the crossing and the cloth fits together; anything below one is an overlap. The values run from 1.000 to 0.955, so the worst overlap in the table is 4.5% of a contact separation — against 22% for a knitted fabric. The overlap rises with the crimp, which is what identifies the mechanism: the vertical gain from moving away from a crossing is the crimp, and a cloth that barely crimps has nothing to gain by moving.

    A woven cloth asked the same question

    A knitted fabric's two adjacent courses occupy the same space by a fifth of a diameter. A woven cloth's two systems overlap by nothing at all in an open cloth and by four and a half per cent in a dense one — and the difference is that they cross rather than run alongside.

    part 17 · weaves
  20. The crest, and the loop that ought to be holding it open. One course of the solved fabric in plan, with the two half periods that meet at a crest marked. They approach to 0.003 mm — 0.018 of a yarn diameter — and run within that of one another for more than a millimetre of arc. The ring drawn between them is the needle loop of the next course, which is what holds them apart in a fabric and what this model does not have: the interlacing was declared a point, and a point holds nothing open. The same omission is what makes the course's writhe zero and its linking number zero, so three of this collection's findings are one defect seen three ways.

    What a contact model would have to do

    This ladder has measured a fabric that does not fit and priced nothing. The repair is a different class of problem from the one this collection solves, it costs fifteen per cent of the yarn in a stitch, and it buys back four results — which is an unusually good return for a piece of modelling.

    part 18 · mechanics
  21. A yarn is pressed on part of its length and free on the rest. The distance from each point of one course to the nearest point of the course below, for a 20 tex cotton jersey at a 3.5 mm loop, along two wales. It runs from 0.780 diameters at the worst to 3.81 at the freest, and 20% of the length is inside one diameter of its neighbour. The line at one diameter is where a round yarn would begin to overlap. What the profile says is that a single flattening ratio is an average: the section a yarn takes changes along its own length, which every racetrack section this collection has drawn assumes it does not.

    A fabric is a population of contacts

    Only a fifth of a knitted fabric's yarn is inside a diameter of its neighbour. So a fabric's friction lives in a fifth of its length, and every calculation this collection makes about withdrawal, slippage and fraying has assumed it lives everywhere.

    part 19 · cloth

All series