Generator

The bearing curves of 4 weaves in one cloth

How much of the plan is within a given depth of the highest point, for plain, 2/2 twill, satin 5, satin 8 — all in sheeting, all at the same sett, the same counts and the same thickness. They differ only in their drafts. At a hundredth of the cloth's thickness the last of them is touching 9 times the area of the first, and the gap widens as the depth shrinks, because the curves do not merely differ by a factor — they have different exponents. A crown that is a line opens as the square root of the depth and a crown that is a point opens in proportion to it.

14 essays call surface-curve. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the weave its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

The surface of a 2/2 twill, in plan. One repeat of a 2/2 twill in sheeting, drawn 2 × 2 times, with every point painted in the colour of whichever thread owns the outside of the cloth there and at an opacity set by how high it is. The range is 221.0 µm from the highest point to the lowest, the root-mean-square roughness is 74.9 µm, and 30% of the plan is hole rather than surface. The bright ribbons are the float plateaux, where a thread lies straight across the threads it passes over and its outside is a horizontal line rather than a point — which is the whole of what follows. The warp crowns at 190.8 µm and the weft at 182.8 µm, a step of 8.0 µm, so the cloth touches the world on its warp alone until anything pressing on it has sunk that far.

What cloth is

A cloth has an outside

Every quantity in this collection is a property of the inside of a fabric — a crimp, a cover, a hole, a fibre count. None of them says where the cloth stops. The outside is a height field the draft computes, its crowns stand at two different levels, and which of the two is higher decides what the cloth touches the world with.

What cloth is

The curve that says what a cloth touches with

Take a cloth's surface and ask what fraction of the plan lies within a given depth of its highest point. The answer is one curve, it answers every question of the form what does this touch, and its behaviour at the top is decided by a single bit of the draft — whether the longest float is one crossing or more than one.

The crown line of every four-by-four draft there is. All 22,874 four-by-four drafts in which every end and every pick interlaces at least once, at sheeting's construction, counted by how much horizontal crown line each carries per square millimetre. The bar at zero holds 2 of them — the two plain weaves, and nothing else in the catalogue. Every other draft has a float somewhere, and a float is a plateau, and a plateau is a line of constant height. So the whole catalogue divides into two drafts that touch at points and 22,872 that touch along lines, with no intermediate case, because a float is either present or it is not.

What cloth is

Two drafts of twenty-two thousand

Every four-by-four draft there is, measured by how much horizontal crown line its surface carries. Two of them carry none — the plain weave and its translation, and nothing else in the catalogue — and the quantity turns out to be smallest for the most balanced cloths and largest for the most one-sided, which is the opposite of what a float count suggests.

single jersey, as loops. Three courses of the same structure drawn as yarn. A knitted needle takes a new loop through the one below; a tuck takes the yarn into the loop below and leaves it on the needle, so that loop is held for another course; a miss floats straight past. Six needles is as many as a loop diagram can carry, which is why the array beside it exists.

Knits and other structures

A jersey has two surfaces

The face of a plain knit shows the legs of its loops, which run along the wale; the back shows the heads and feet, which run across it. So the two faces carry their crowns at right angles — the same situation as a damask's figure and its ground, in a fabric with no warp, no weft and no float.

$What it costs to touch a cloth. The pressure needed to bring a stated fraction of the plan into contact, for plain, 2/2 twill, satin 8 in sheeting. Reaching two per cent of the plan takes 2.83 kPa on a plain and 0.05 on a satin 8, a factor of 55. The stiffness in this figure is fitted and is labelled as such. A yarn's resistance to being squashed out of round has no lower bound at all — a bundle of fibres free to slide is a fluid in cross-section — so no bracket exists to compute this from, and what is used is the value this collection fitted to measured fabric thickness. Every curve moves together across its published range, which is why the ratio between weaves survives and the absolute values are quoted with the fit named.$ What cloth is

How much of a cloth is touching

Press a fabric against a flat plate with the weight of a hand and ask what fraction of it is actually in contact. The bearing curve answers, and the answer is about four per cent — of which the great majority is not the cloth's surface at all, but the hairs standing off it, which nothing in this arithmetic can see.

Three kinds of surface, and only one of them starts open. The bearing curves of a 2/2 twill in sheeting, of a terry loop pile, and of a cut corduroy pile of 30 tex, over the first six per cent of a cloth's thickness. The woven curve opens as the square root of the depth and the loop pile's does the same, because a loop's top is a curved thread like any other. The cut pile does not open: it is a flat line at 5.2% of the plan, from a depth of nothing, because a blade severed every tuft in one pass and left every end in one plane. That is not a larger contact area, it is a different kind of contact area — one that does not vanish as the load goes to zero, which is a property no woven surface has.

Compound and figured cloths

A pile is the only surface with no crowns

Every other fabric touches on the tops of curved threads, so its contact vanishes as the load goes to zero and the pressure on what is touching rises without limit. A cut pile touches on flat ends left in one plane by a blade — so its contact is finite at no load at all, its pressure concentration is bounded, and it is the only fabric whose abrasion mass loss is an honest measure of its damage.

$A cloth loses its strength long before it loses its mass. Rubbing a 2/2 twill in sheeting down, plotted against how much of its own solid volume has gone. The lower curve is the fraction of the plan the rubbing is touching; the upper is the fraction of the warp's section that has been cut away. They are wildly different because the wear is spread and the damage is concentrated: material comes off the whole surface, but it comes off every thread at the same place, and a thread breaks at its thinnest place. At one per cent of the mass gone the section is already 5% smaller. That is why a fabric that looks barely worn fails a strength test, and why abrasion resistance measured as mass loss and abrasion resistance measured as residual strength are two different quantities that are quoted as one.$ Cloth doing a job

A cloth loses its strength before its mass

Rub a fabric and it sheds material from all over its surface, but it sheds it from every thread at the same place — and a thread breaks at its thinnest place. So the strength gone is always several times the mass gone, the ratio is computable from the bearing curve, and it is worst for the weave whose crowns are points.

What it takes to bury a cloth's crowns. The film needed to fill a fabric's surface to a stated level, for plain, 2/2 twill, satin 8 in sheeting, at a film density of 1.2 g/cm³. Burying the crowns entirely takes 187 g/m² on the plain, 186 g/m² on the 2/2 twill, 183 g/m² on the satin 8 — and the ordering is not the ordering of roughness. A weave with plateaux presents a wide flat top that a thin film covers, and a weave with points presents crowns with valleys between them that the film has to fill before it is continuous anywhere. Every gram spent filling a valley is a gram that is not bridging a hole, which is where a coated cloth fails.

After the loom

A coating fills the crowns before it bridges the holes

A film does not sit on a cloth, it fills it — and the volume it has to supply to reach a level is the integral of one minus the bearing area. Burying an ordinary sheeting's crowns takes 185 grams a square metre, which is more than the cloth weighs, and the whole of the weave's influence is spent in the first ten of them.

$Two cloths touch on a fraction of what one cloth does. A 2/2 twill in sheeting pressed against a flat plate, and the same cloth pressed against another piece of itself. At an approach of 24.9 µm the single surface is touching 15.87% of the plan and the pair 3.130% — a factor of 5. The reason is that a gap between two rough surfaces is the sum of two depths, so both surfaces have to be near their own maxima at the same place, and the chance of that is the product of two small numbers. The pair's curve is the convolution of the two height distributions, computed exactly on histograms rather than fitted to a Gaussian — because a woven surface is bimodal and nothing about it is Gaussian.$ After the loom

Friction is two surfaces, not one

A gap between two rough bodies is the sum of two depths, so two cloths face to face touch on the convolution of their height distributions rather than on either of them. At the approach a light touch produces that is twenty times less contact than the same cloth against a plate — which is why a fabric's friction against a plate and against another fabric are two different measurements.

$Two exponents in a compression curve. How far a flat plate sinks into plain, 2/2 twill, satin 8 in sheeting, against the pressure it is applying, on logarithmic axes where a power law is a straight line. The measured slopes over the light end of the range are 0.50 for the plain, 0.67 for the 2/2 twill, 0.67 for the satin 8 — against two thirds predicted for any weave carrying a float and one half for a weave carrying none. The prediction is one line of algebra: pressure is a stiffness times a strain times a bearing fraction, the bearing fraction is a square root of depth for a plateau and linear in it for a point, so the pressure is the three-halves power in the first case and the square in the second. Nothing is fitted to produce it; the slopes are measured afterwards and compared. At the heavy end every curve bends, because the crowns have merged and the cloth has stopped being a surface and started being a solid — which is a different regime with a different law, and it belongs to the compaction of a fibre mass rather than to the geometry of an interlacement.$ Mechanics and drape

A cloth compresses along its own bearing curve

A fabric's pressure–thickness curve is always fitted with an empirical power law and the exponent is reported without explanation. It is not empirical. At light loads it is two thirds for any weave carrying a float and one half for a weave carrying none, and the two numbers come out of one line of algebra with nothing fitted in it.

Setting and geometry

The sett owns the pitch and the yarn owns the height

Set a cloth twice as close and its surface does not get smoother. The crowns come twice as often, because that is what a sett is, and they stand at very nearly the same height, because the closure condition pins the amplitude to the yarn — so a fine cloth is finer-grained rather than flatter, and the two are confused in every description of handle.

Weaves

A crepe is flat in its draft and not in its surface

A crepe weave is chosen by pushing the draft's correlations as flat as they will go. That criterion turns out to tie: on the base this collection uses, 4,416 of the 5,040 rearrangements reach the floor. Sixteen of them additionally spread their crown line perfectly evenly — and the crepe actually drawn is not one of the sixteen.

The four-by-four catalogue's crown line, counted three ways. Every one of the 22,874 interlacing four-by-four drafts, binned by how much horizontal crown line it carries, under three counts: both systems summed, which is what the published census reports; the warp alone; and the weft alone. A bearing curve sees one system, because a plate meets whichever crown stands higher and meets nothing else until it has sunk past the step between them. Under the summed count 2 drafts carry none; under the warp alone 494 do, and under the weft alone 494. What the histogram cannot show is which drafts moved, which is most of them.

What cloth is

The census counted two systems and a surface has one

Two drafts of twenty-two thousand touch at points, and the two are the plain weave. That is a count of the crown line both systems carry, and a bearing curve sees one: a plate meets whichever crown stands higher and meets nothing else until it has sunk past the step. Counted the way a surface is read, 494 drafts touch at points rather than two — and which 494 depends on a crimp division already called a convention rather than a measurement.

The bearing crowns of 2/2 twill and 2/2 hopsack, over 3 repeats. The cells at which the warp is on the face, drawn over 3 repeats of each draft — which is the surface a plate meets, since the other system is a step below it. 2/2 twill has 1 component in its repeat and a path that runs the whole way across the cloth, in both directions; 2/2 hopsack has 2 components in its repeat and no path across the cloth at all. Both carry the same length of crown line by the bearing count, and one is a ridge while the other is a field of islands. What the drawing cannot show is the depth of the gaps between them, which is the step to the second system and is a few micrometres.

What cloth is

Four drafts in five have no path along their own crowns

A 2/2 twill and a 2/2 hopsack carry exactly the same length of bearing crown line, which the surface census noted and could not explain. One of them is a ridge running diagonally across the cloth without a break; the other is a field of square islands with no path between them. Counted over the whole catalogue, 4,016 of 22,874 drafts have a crown path that reaches the far side, 1,616 have one in both directions, and 130 have crowns with no neighbour at all.

The whole library · All essays