Textile Structure
how cloth is put together
Generator

The shed in section

The shed in section
The shed in section. A warp line 1200 mm from the fell of the cloth at the left to the back rest at the right, with 8 shafts at 300 mm and every 16 mm behind it. Each shaft lifts its ends in proportion to its own distance from the fell, which is what gives the same 30 mm clear opening at the reed from every shaft. The resulting extension is 0.460 per cent at the front shaft and 0.722 per cent at the back, a ratio of 1.57. Vertical scale exaggerated 4 times.

A warp line 1200 mm from the fell of the cloth at the left to the back rest at the right, with 8 shafts at 300 mm and every 16 mm behind it. Each shaft lifts its ends in proportion to its own distance from the fell, which is what gives the same 30 mm clear opening at the reed from every shaft. The resulting extension is 0.460 per cent at the front shaft and 0.722 per cent at the back, a ratio of 1.57. Vertical scale exaggerated 4 times.

6 essays call loom-section. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the weave its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

The shed in section. A warp line 1200 mm from the fell of the cloth at the left to the back rest at the right, with 8 shafts at 300 mm and every 16 mm behind it. Each shaft lifts its ends in proportion to its own distance from the fell, which is what gives the same 30 mm clear opening at the reed from every shaft. The resulting extension is 0.460 per cent at the front shaft and 0.722 per cent at the back, a ratio of 1.57. Vertical scale exaggerated 4 times. Mechanics and drape

The shed is an extension

Every model of a finished cloth treats a thread as inextensible, and every one of them is about a fabric that has left the loom. On the loom the warp is stretched thousands of times a minute by the shed itself, and the amount is exact trigonometry with nothing fitted in it: the square of the shed's tangent, times the shaft's own distance from the fell, over twice what is left behind it.

 The strain across a harness. The warp strain each shaft of a 24-shaft harness puts into its own ends, from 0.460 per cent at the front to 1.728 per cent at the back. Shafts within a budget of 1.0 per cent are drawn in one colour and those outside it in another; the budget is reached at shaft 13. Mechanics and drape

The back shaft works hardest

How hard the loom is on a warp end is the product of two numbers from different worlds — how often its column changes sides, which is a property of a binary matrix with no millimetre in it, and the strain of the shaft it happens to be on, which is a property of a machine with no weave in it. Neither knows about the other, and the threading that joins them is a decision nobody makes on structural grounds.

 Flexes per end in the same check, ground a pick along. One bar per warp end above the draft of the same check, ground a pick along, each the number of times that end changes sides in one repeat — which is the number of times the shed drags it through its heddle eye. The counts run from 6 to 10, and they are the same numbers that give the cloth its interlacing rate of 0.500 per intersection. Mechanics and drape

A figure is harder on its warp

Every basic weave flexes all its ends exactly as often as each other — plain, twill, satin and sateen alike, and it is a one-line theorem. Figure one of them on another and that evenness goes, or does not, depending on where the ground weave was started relative to the figure. The same invisible offset that decides whether a fine figure holds together decides, at a coarse one, how unevenly the loom works the warp.

 The reed is not the sett. Twelve ends held at the reed's pitch above and at the cloth's pitch below, for a sheeting whose weft crimp is 14.61 per cent. The count is the same in both rows and only the spacing changes: the cloth is 12.75 per cent narrower, so a reed at 24.43 ends per centimetre produces a cloth at 28. The crimp comes from the Peirce solution at this cloth's quoted construction. Setting and geometry

The reed is not the sett

A reed holds the warp at a pitch, and the cloth that leaves it is narrower — by exactly the weft's crimp, with nothing fitted and nothing approximated. On a close balanced sheeting that is 12.75 per cent, on an open scrim 1.87, and a weaver who allowed one figure for both would be wrong by a factor of nearly seven.

 What the two setts can be set to. Two rules on one scale from 8 to 40 threads per centimetre. The upper carries the 49 warp setts a metric reed catalogue reaches at one to four ends per dent; the lower carries the 4825 pick densities a change-wheel take-up reaches. The mean spacing is 0.656 threads per centimetre in the warp and 0.0066 in the weft, a ratio of 99. The widest gap in the reed's range is 2.10 threads per centimetre. Setting and geometry

The setts a loom can reach

Transposing a draft gives a perfectly good draft, and every count this site takes off a matrix either is symmetric under exchanging warp and weft or has a mirror twin. The loom is not symmetric at all: over the range ordinary cloth is woven in, it can choose a pick density 99 times more finely than a warp sett — and the warp sett cannot be changed once the warp is drawn in, at any granularity whatever.

 The harness a strain budget buys. How many shafts stay inside a 1.0 per cent warp-strain budget, against the clear shed opening the loom needs at the reed: 12 mm gives 43, 16 mm gives 36, 20 mm gives 28, 24 mm gives 21, 30 mm gives 13, 36 mm gives 7, 44 mm gives 1. The shed's tangent enters the strain squared, so the opening is much the strongest thing a loom builder controls. Compound and figured cloths

The harness has a depth

Why does a dobby carry sixteen or twenty-four shafts rather than two hundred? The usual answers are about the mechanism — how many jacks a box can drive, how many hooks a dobby has — and they are real limits that are not the binding one. A stated tolerance on warp strain is a stated distance from the fell, and a stated distance is a whole number of shafts. One per cent buys thirteen.

The whole library · All essays