Textile Structure
how cloth is put together
Generator

The draft for 2/2 twill, as a loom holds it

The draft for 2/2 twill, as a loom holds it
The draft for 2/2 twill, as a loom holds it. The 2/2 twill written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it.

The 2/2 twill written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it.

12 essays call harness. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the weave its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

A 2/2 threading, run out to three widths. The same four shafts threaded for repeats of increasing width. The threading line runs up and back down; the harness never grows, and the number of ends it carries is bounded by the loom's width rather than by its shafts. Compound and figured cloths

The harness does not grow

Nearly every account of a loom says the shaft count limits the repeat. It limits the repeat of a straight draw, and of nothing else — a reversed twill on ninety-six ends weaves on the same four shafts as the twill it was made from, and the ratio grows without bound.

 The draft for herringbone, as a loom holds it. The herringbone written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it. Compound and figured cloths

What a dobby stores

A pattern chain does not store picks. It stores lifts — the distinct sets of shafts a draft ever raises — and for most drafts worth weaving that number is very much smaller than the number of picks, which is the second half of the reason a wide repeat is affordable.

 The draft for 8-end satin, as a loom holds it. The 8-end satin written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it. Compound and figured cloths

A jacquard is every end its own shaft

The machine is usually described as the one that weaves anything. What it actually does is abolish one of the loom's two budgets and make the other proportional to the width of the repeat — which turns a constraint on the design's kind into a constraint on its size, and those are very different things to be short of.

 Figure and ground on 8 ends. A damask is a satin and its own complement. The figure is warp-face and the ground is weft-face, they carry the same longest float and need the same shafts on the same threading, and the whole of the pattern is carried by which system is on top. Compound and figured cloths

A damask is its own complement

The pattern is carried by direction alone. Figure and ground are the same satin, one warp-face and one weft-face, with the same longest float, the same shaft count and the same threading — so the cloth's most famous effect costs it no structural difference whatever between the two areas.

 What a figure costs in shafts. Two families of block designs in 8-end satin on 8-end sateen at blocks of 8. One repeats three block-columns however wide it gets and costs 24 shafts at every width from 24 to 120 ends. The other gives every block-column a different pattern and costs 16, 24, 32, 40, 48 shafts as it grows — exactly 8 more per new column. Shafts are counted as distinct columns of the composite matrix. Pattern and colour

What a figure costs the loom

A block design's shaft count does not depend on how wide the figure is, or how deep, or how many blocks it has. It depends on how many *different* block-columns it has, and each new one costs exactly one repeat of the ground weave — 8 shafts, then 16, then 24, in a straight line with no slope to fit.

 The draft for 2/2 twill, as a loom holds it. The 2/2 twill written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it. Weaves

How many shafts a draft needs

Every quantity this site has counted so far is a property of the cloth. This one is a property of the loom — the number of distinct columns in the matrix — and it is very probably the strongest single predictor of which of the twenty-two thousand four-by-four drafts anybody ever wove.

 An 8-end weft-faced satin through a point tie on an end. The 8-end satin on a move of 3, weft-faced, woven through a point tie of 12 hooks that turns on a single end, so 22 ends carry one repeat. The strip above is the tie, hook number against end. Inside the satin the weft floats 7 ends; across the turn it floats 13, outlined, because on some pick the nearest interlacing is 7 ends away on both sides. What the drawing cannot show is how a long float at one line down the cloth behaves in use, which depends on the yarn and the finish rather than on the count. Compound and figured cloths

A point tie nearly doubles the float at the turn

A point tie halves the hooks a symmetrical figure needs by driving every hook's end twice, out and back. It mirrors the ground as well, and a satin is symmetrical about no end: across the turn its weft floats 2n − 3 ends, or 2n − 2 between ends, at every hook count and wherever the satin starts. At eight ends that is thirteen or fourteen against seven — and the turn's other promise, more repeats that fit the width, is not kept either.

 A jacquard harness 130 cm wide under a 150 cm fall. A jacquard harness in front elevation, to scale: hooks spread over 40 cm, cords fanning down 150 cm to a comber board 130 cm wide, and hanging straight from the board to their mails. The centre cord is vertical and lifts its mail by the whole 10 cm hook lift; the edge cord leans 16.7° and lifts its mail 9.60 cm, 96.0% as far, and its bend at the board adds 9% to the hook's load at a friction coefficient of 0.3. What the drawing cannot show is the tie that decides which hook feeds which hole, which in a real mount is not the simple spread assumed here. Compound and figured cloths

A jacquard harness needs three half-spans of height

A jacquard has no front shaft and no back one, so every end takes the same shed — as long as every cord hangs straight. Across the width they cannot: the hooks sit in a machine a few tens of centimetres wide and the comber board is as wide as the cloth, so an edge cord leans and its mail rises by the difference of two hypotenuses rather than by the hook's lift. Holding the edge shed within five per cent of the centre's takes a fall of about three times the edge cord's sideways reach, and that is a height a room has to have.

 The draft for 2/2 twill, as a loom holds it. The 2/2 twill written the way a weaver writes it: the threading above, saying which shaft each end hangs on; the lifting plan to the right, saying which shafts rise on each pick; and the cloth below, which is not copied from the weave but produced by running those two against one another and then checked against it. What cloth is

A lifting plan says nothing without a threading

The second of the notations for something larger than a weave is a pair, not a notation: a threading and a lifting plan, and neither alone expresses anything. The pair's image is exactly the drafts with no more distinct columns than there are shafts — 98 at two shafts, 5,282 at three, all 22,874 at four — and it is not nested with the profile draft's in either direction. The profile reaches 192 drafts that need all four shafts, and misses 64 of the 98 a two-shaft loom weaves.

 A comber board for 60 ends a centimetre, in side elevation. A jacquard's comber board seen from the side, with the fell of the cloth at the left and the back rest at the right. The board carries one hole per end; at 60 ends a centimetre the ends are 0.167 millimetres apart and a cord with a mail on it needs 0.9, so the holes are ruled in 6 rows staggered fore and aft, 6 millimetres apart — a harness 30 millimetres deep. Each row's ends are strained by its own distance from the fell: 0.460 per cent at the front and 0.524 at the back, a spread of 0.0636. What the elevation cannot show is the sideways fan of the cords above the board, which is a separate and much larger geometry. Compound and figured cloths

A jacquard's harness has a depth after all

A jacquard was said to escape the shaft loom's depth entirely, because every mail hangs at the same distance from the fell. Every mail does, if the comber board has one row of holes — and it cannot. At sixty ends a centimetre the ends are a sixth of a millimetre apart and a cord with a mail on it wants most of one, so the holes are ruled in six rows thirty millimetres deep. The escape is real and it is a factor of eight rather than a release, and it closes as the cloth is set finer.

 What each figure-and-ground pairing costs in differential take-up. For each pairing of a figure weave with a ground weave, the difference between the two regions' warp crimps and the length of figure that difference allows before an end goes slack, taking the loom to absorb 1.2 millimetres. a damask: satin on its own complement: 0.00 per cent apart, no bound; an eight-end satin figure on a five-end satin ground: 0.31 per cent apart, a figure up to 392 millimetres; a five-end satin figure on a 3/1 twill ground: 0.90 per cent apart, a figure up to 133 millimetres; an eight-end satin figure on a 2/2 twill ground: 3.02 per cent apart, a figure up to 40 millimetres; an eight-end satin figure on a plain ground: 14.15 per cent apart, a figure up to 8 millimetres; a 2/2 twill figure on a plain ground: 11.14 per cent apart, a figure up to 11 millimetres. A damask's two regions are the same satin used two ways, so complementation leaves both float lengths where they were and the crimps are identical rather than close. What the bars cannot show is the slack, which is an input and which every length is proportional to. Compound and figured cloths

A damask is the only figure that costs its beam nothing

Figure and ground consume warp at different rates, and the difference accumulates down the length of the figure. An eight-end satin figure on a plain ground puts its two regions fourteen per cent apart, which on a loom absorbing a millimetre of slack bounds the figure at eight and a half millimetres. A damask's two regions are the same satin used two ways, so complementation leaves both float lengths where they were — and their crimps are identical rather than close, to the last bit of a double.

 The beams a disc 12 blocks across needs, column by column. A disc 12 blocks across, 12 blocks by 12, figure shaded, with the beam feeding each column of ends written above it, for a figure floating 8 on a ground floating 1, whose warp crimps are 14.15 per cent apart, at 4 mm blocks over a 100 m piece with 1.2 mm of slack. It has 4 distinct columns and 4 distinct shares of the repeat in figure, and needs 4 beams. What the grid cannot show is the cloth's own crimp interchange, which would move tension between the columns instead. Compound and figured cloths

A figured warp needs a beam for every share of its figure

Figure and ground take up warp at different rates, so a figured cloth on one beam is bounded in how long its figure may run, and a second beam is the obvious escape. It escapes only for ends that live wholly in one region. An end that crosses the figure for part of the repeat consumes warp at its own rate, and two ends can share a beam only if they spend the same share of the repeat in the figure and never drift a slack apart inside it. So a round figure twelve blocks across needs four beams, ninety-six blocks across needs twenty-nine, and any crimp difference at all — a third of a per cent will do — costs every one of them over a piece.

The whole library · All essays