Generator

The stiffness bracket, against the count

The two bounds on a cotton yarn's bending rigidity, from 6 to 100 tex, on a logarithmic scale because they are hundreds apart. The lower line is the sum of the fibres' rigidities and the upper is a solid rod of the yarn's own diameter. The vertical gap is the fibre count divided by the square of the packing factor, exactly, so it widens in proportion to the count: 98 at the fine end and 1,634 at the coarse. What the plot cannot show is where a real yarn lies between the lines.

14 essays call force-curve. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the weave its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

The force at a crossing. One warp end of a sheeting riding over three picks, with the weave angle Peirce's geometry solves for at that construction: 36.8°. An end held at 0.50 N presses each pick it crosses with 0.599 N, which is twice the tension times the sine of the angle and has no material constant in it. What the drawing cannot show is the relaxed case: a cloth with no tension in it still holds its threads together, and what does the holding then is the yarn's own resistance to being bent, which needs an elastica this site does not have.

What cloth is

Every crossing is a force

A thread arrives at a crossing at an angle and leaves at its negative, so the two pulls have transverse parts that add. The force pressing one thread onto another is twice the tension times the sine of the weave angle — and for an ordinary sheeting that is more than the tension in the thread itself.

Where a thread stops sliding and starts breaking. A pick of sheeting gripped over a length of cloth, drawn one crossing at a time. The resistance is 0.30 times the 0.599 N each crossing presses with, so it rises with the length held; the breaking load of 3.74 N does not. The two are equal at 7.4 mm. What the drawing cannot show is that μ is a range rather than a constant, so the mark is a band and its position is exactly inversely proportional to the friction.

What cloth is

A thread is held one crossing at a time

Grip a thread over a length of cloth and its resistance to being pulled out rises with that length, because it is held at every crossing it makes. Its own breaking load does not rise at all. The two curves cross, and the length at which they cross turns out to be a seam allowance, a frayed edge and a tuft's anchorage — three rules of thumb with one number under them.

The loop that costs nothing to extend. A plain knitted loop at rest and extended by 35 per cent, with the arcs marked. The arcs' radius is the diameter of the yarn the loop wraps, 0.167 mm, and it is set by contact rather than by the fabric's dimensions — so extending the fabric lengthens the legs and bends nothing further. The bending energy is 0.0176 N·mm at both, and the model therefore asks no force at all for an extension a woven cloth would refuse. What the drawing cannot show is what a real knit's first few per cent do cost, which is friction and yarn flattening and is not a bending property.

Knits and other structures

A knit is soft because it bends

Ask the same energy question of a woven cloth and a knitted one and the answers are not different by a factor — they are different in kind. A woven cloth's bending energy changes the moment it is extended. A knitted loop's does not change at all, exactly, over the whole of its extension, because its arcs are held to a radius by contact rather than by the fabric's dimensions.

The two calculations a yarn's stiffness admits. A bundle of 9 fibres bent with the fibres free to slide and with them locked together. Free, the rigidity is the sum of the fibres': 0.00141 N·mm² for a 30 tex cotton yarn. Locked, it is the fourth power of the yarn's own diameter: 0.689. The ratio is the fibre count over the square of the packing factor, 490, and nine fibres are drawn where the yarn has 176. What the drawing cannot show is where a real yarn sits between them, which is a question about friction rather than about fibre.

Mechanics and drape

A yarn's stiffness is a bracket, not a number

Two calculations are available for how stiff a thread is in bending, and both are exact. One treats the fibres as free to slide and gives the sum of their stiffnesses; the other treats them as locked and gives a solid rod. They differ by the fibre count, which for an ordinary cotton yarn is a factor of five hundred — and no measurement of the fibre narrows it by anything at all.

Setting and geometry

The crimp ratio is not a measurement

Peirce's geometry is two thread systems, four unknowns and three equations. It cannot say how the crimp divides between warp and weft, so every cloth solved so far has been drawn at a ratio somebody chose. Give the threads a stiffness and the missing equation arrives — and for six of the eight cloths in the table it arrives with no material constant in it at all.

A knit's restoring force, and the column that does not move. A plain knit of 20 tex cotton at a loop length of 3.5 mm, over the extension range its own geometry admits. The bending energy stored in one loop is the same number at every extension — the loop's arcs are held to a radius by the thread they wrap rather than by the fabric's dimensions, so extending the fabric does not bend anything more. The frictional resistance at the interlocks is not zero: it is μ times the force pressing there, times 2.34 interlocks per millimetre of width. So a knit's resistance to extension is dissipative rather than elastic, which is why it does not spring back and why its dimensions depend on how much it has been agitated. What the rows cannot show is the interlock force itself, which this site does not have for a knit and which is recorded as missing.

Knits and other structures

What stops a knit extending

A knitted loop's bending energy does not change as the fabric extends — exactly, over the whole range its geometry admits. Something resists, and it is not stiffness. It is friction at the interlocks, which is dissipative rather than elastic, and that single fact accounts for why a knit does not spring back, why a softener changes its dimensions and why the constants its size is quoted with contain no yarn property at all.

What a shed costs, in newtons. The tension the shed puts into one end at each shaft of a 24-shaft harness, for a 25 tex cotton yarn. The strain is set by the loom's geometry alone; the tension is that strain times the yarn's modulus. The front shaft holds 0.52 N and the back 1.95 N, which is 14 and 52 per cent of the yarn's breaking load. What the chart cannot show is the rest of the warp tension, which the let-off adds on top of all of these and which no geometry decides.

Mechanics and drape

What the shed costs, in newtons

The shed's strain has been computed here and could not be priced: a strain is a length over a length and says nothing about how hard a thread is being pulled. A modulus turns it into a tension — and the back shaft of a twenty-four-shaft harness turns out to hold its ends at half their breaking load, all day, from the geometry alone.

The beat-up, at the fell. The last picks of a sheeting at 26 picks per centimetre, with the beat-up zone shaded. Driving the fell forward makes the warp take more crimp and more crimp takes more thread, which the warp can only supply by stretching — so the force is the warp tension times the crimp's elasticity with respect to the pick spacing, 0.182 here. That is 0.205 N per end and 573 N per metre of reed. What the drawing cannot show is that the shaded band's width cancels out of the derivation exactly; it is drawn because a reader needs to see what is being compressed, not because the answer depends on it.

Setting and geometry

The blow that sets the pick

The take-up gear decides how far the cloth moves between picks and says nothing about the blow that puts each pick where it goes. That blow is a force, and a virtual-work argument gives it in one line — with the length of the beat-up zone cancelling out of the answer exactly, which is the part worth having.

The load–extension curve, computed from a stiffness. The tension in one end of a sheeting against how far the cloth has been extended, computed as the slope of its bending energy along its own constant-thread-length locus. The curve passes through zero at the state of least energy, which is where an unloaded cloth sits, and rises either side of it. What the curve cannot show is what happens after the crimp runs out: past the end of the locus the load is carried by stretching yarn rather than by straightening it, and that is a modulus three orders of magnitude higher and a different figure.

Mechanics and drape

The locus gets a force

This site has drawn the set of states a cloth can reach without stretching any yarn, and has never been able to say which of them it is in or what it would cost to move. Both questions are one derivative of a bending energy — and the answer explains the flat start every fabric's load–extension curve has, which is not slack yarn but a symmetry.

The resting band, not the resting point. The bending energy of a sheeting along its own constant-thread-length locus, with the band in which friction can hold it shaded. The minimum is a single state; the band is 10.9 per cent of length wide, because the cloth stops sliding as soon as the energy it can release falls below the 0.0756 N friction takes to move a crossing. What the drawing cannot show is which end of the band a given piece of cloth stops at, which depends on the direction it arrived from and is what makes relaxation hysteretic.

After the loom

A cloth relaxes until its threads stop pushing

The finishing field treats the relaxed state as a place a cloth arrives at. With an energy along its own locus and a friction at its crossings it is not a place but a band — and which point of the band a piece of cloth stops at depends on which side it came from, which is why washing it twice gives two answers.

Selectable against reachable. How far up the take-up gear's catalogue a beat-up force reaches, on a sheeting. The catalogue holds 4,825 distinct pick densities between 8 and 40 per centimetre, which is the previous rung's count of what the machine can select. At 200 N per metre only 548 of them can be woven; at 2,000 it is 4,256. The fineness of the choice is untouched by the ceiling and the top of the range is cut off entirely, so the weft direction's advantage is resolution rather than reach. What the chart cannot show is the loom's own force, which depends on the beat-up mechanism and is not a property of the cloth.

Setting and geometry

A pick density is a force budget

The take-up ladder counted what a change-wheel take-up can select: 4,825 distinct pick densities between eight and forty threads per centimetre, against forty-nine warp setts a reed catalogue offers over the same range. That count assumed every setting is available. A beat-up force says otherwise, and cuts the top off the range without touching the fineness of the choice.

Compound and figured cloths

What holds a tuft in, in newtons

The pile ladder computed a tuft's anchorage as a capstan ratio and said, correctly, that a ratio was all it could offer. A ratio multiplies a tension and there was no tension anywhere on this site. There is one now — and the answer, put beside what a carpet is actually specified at, falls short by a factor of three.

Which seams slip and which break. For each cloth, the grip a 10 mm seam allowance offers divided by the thread's own breaking load. Above one the fabric or the thread gives first and the seam holds until it does; below one the threads slide out and the seam opens with the cloth intact. voile, batiste, poplin, sheeting break; cheesecloth, muslin, duck, filter slip. The allowance that would save every cloth in the table is 74 mm, which is set by the openest of them alone. What the chart cannot show is the stitching itself, which has its own strength and its own way of cutting the threads it passes through.

Cloth doing a job

A seam slips before it breaks

A sewn seam fails in one of two ways and the trade names them separately: the threads pull out of the cloth beside the stitching, or something breaks. Which one a given cloth does is decided by whether its seam allowance clears the length at which grip beats strength — and at the ordinary ten millimetres, the table divides four against four.

Elastic recovery against strain, for seven fibres. The elastic recovery of seven fibres at the strains it is reported at: extend to a stated strain, unload, read the strain returned immediately. Each fibre's points are joined and the line stops where the measurements stop, which is the point of the figure — a fibre strained past the last point on its own line is a fibre this collection declines to answer for. Nothing here is measured below one per cent of strain, and a woven cloth just past its own interchange budget is at a thread strain of a few hundredths, so the region that matters most for a fabric is the region nobody has reported. Recovery falls monotonically for every fibre, which is what lets the unmeasured region be bracketed between the lowest measured value and one rather than extrapolated. What the plot cannot show is the delayed recovery, which is excluded by the convention and is largest for the fibre with the best reputation for recovering.

Mechanics and drape

Recovery is measured and nothing predicts it

A fibre's stiffness is a bracket this collection can compute the ends of. What fraction of a strain it gives back is not: it has to be looked up, the tables are thin, they stop exactly where a fabric needs them, and the most attractive explanation for the ordering they show turns out to have no signal in it at all.

The whole library · All essays