Textile Structure
how cloth is put together
Generator

What leaving the plane costs, which is less than nothing

What leaving the plane costs, which is less than nothing
What leaving the plane costs, which is less than nothing. Bending energy a stitch against how far the yarn climbs between one interlacing and the next, for a 20 tex cotton jersey at a 3.5 mm loop. The curve falls. A climb is not an extra bend added to a curve that was otherwise unchanged; it is part of the straight line the thread has to span, so a longer climb leaves less slack to be spent on curvature. At a jersey's own climb of one diameter the energy is 24395 nJ against 25060 for the planar model — 2.7% lower, where an earlier estimate on this site put the ride at three per cent of the loop's bending and had the sign the other way round. At a rib's climb of three or four diameters the fall is 33%.

Bending energy a stitch against how far the yarn climbs between one interlacing and the next, for a 20 tex cotton jersey at a 3.5 mm loop. The curve falls. A climb is not an extra bend added to a curve that was otherwise unchanged; it is part of the straight line the thread has to span, so a longer climb leaves less slack to be spent on curvature. At a jersey's own climb of one diameter the energy is 24395 nJ against 25060 for the planar model — 2.7% lower, where an earlier estimate on this site put the ride at three per cent of the loop's bending and had the sign the other way round. At a rib's climb of three or four diameters the fall is 33%.

13 essays call climb-curve. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the weave its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

A rib crosses a gap where a jersey crosses a diameter. A one-by-one rib in section across 5 wales, drawn at a bed gap of 3 yarn diameters — 0.501 mm — because the relaxed gap of a rib is a measurement this collection does not hold and every figure of one says what it was drawn at. Alternate wales sit on opposite beds, so every sinker loop between them travels the whole gap. In a jersey the same yarn climbs one diameter, 0.167 mm. That single difference takes the contact force from 38.30 mN at 11.7° out of the fabric to 72.51 mN at 16.2°, and the through-thickness part from 7.81 mN to 20.17 mN. Knits and other structures

A rib climbs a gap

A jersey's yarn crosses one diameter between interlacings because that is what a crossing of two threads is. A rib's crosses the whole distance between the two beds. Nothing else in the model changes, and that one length is the whole mechanical difference between the fabrics.

 The contact force turns as the climb grows. The two components of the contact force against the climb, for a 20 tex cotton jersey at a 3.5 mm loop. The force along the wales is what friction has to hold and the force through the thickness is what holds the fabric open, and the second is bought at the expense of the first. At a jersey's own climb of one diameter they are 37.50 mN and 7.81 mN; at four diameters, which is a rib on an open gap, they are 22.39 mN and 18.61 mN. The friction balance is the ratio: friction has the whole force to work with and only the along-the-wales part to hold, so the coefficient a relaxed knit would need falls from a half to 0.490. What cloth is

Every fabric's thread lies in a plane

A woven thread's crimp wave lies in a plane at right angles to the cloth. A knitted loop lies in a plane twelve degrees off it. Both halves of this collection turn out to be one picture with one angle in it, and the angle decides how much of a fabric's contact force acts through its thickness.

 A rib is quietest at a gap of two diameters. The through-thickness force of a one-by-one rib against the bed gap it is knitted at, in units of the yarn's own diameter. It does not rise from the bottom, and the dip is geometry rather than noise: a crossing is shared between the two half periods either side of its sinker loop, and each of those also carries the interlacing's own diameter — one climbing with it and one against. At a gap of two diameters the second half period climbs nothing at all, and the fabric is at its quietest through its own thickness. Above that both halves climb the same way and everything rises together, which is the regime a real rib is knitted in: 14.8 mN at 5 diameters against 7.0 mN at two. Knits and other structures

A rib is quietest at two diameters

Open the beds of a rib and everything about it should get stronger. It does not. The through-thickness force falls to a minimum at a bed gap of exactly two yarn diameters and rises on both sides of it, because a crossing's climb and an interlacing's own climb cancel there.

 A knitted loop is a plane curve in a plane that is not the fabric's. A relaxed 20 tex jersey at a 3.5 mm loop, seen from the end of a course. Each course is a straight line because it is one: a half period leaves and arrives along the course direction, so the plane it bends in contains that direction, and a plane curve seen along a line in its own plane projects to a segment. The upper panel expands the thickness 3× so the arrangement can be seen and no angle may be measured off it; the lower panel is the same fabric at one scale, where the tilt is what it really is. The angle is 11.75°: a climb of one yarn diameter, 0.167 mm, against a drop of a course spacing and a diameter, 0.803 mm. Successive courses overlap by exactly one diameter, which is the interlacing, and the fabric is therefore 0.334 mm thick — two yarn diameters, with nothing fitted. After the loom

A state is a thickness too

This collection's rule is that a fabric dimension quoted without its relaxation state is not a measurement. A knitted fabric has three dimensions and only two of them obey the rule: its thickness is the same in every state, because the interlacing that sets it does not relax.

 What leaving the plane costs, which is less than nothing. Bending energy a stitch against how far the yarn climbs between one interlacing and the next, for a 20 tex cotton jersey at a 3.5 mm loop. The curve falls. A climb is not an extra bend added to a curve that was otherwise unchanged; it is part of the straight line the thread has to span, so a longer climb leaves less slack to be spent on curvature. At a jersey's own climb of one diameter the energy is 24395 nJ against 25060 for the planar model — 2.7% lower, where an earlier estimate on this site put the ride at three per cent of the loop's bending and had the sign the other way round. At a rib's climb of three or four diameters the fall is 33%. After the loom

A rib's relaxation is not its bending either

A jersey does not settle where its bending energy is least, and this collection has said so for several rungs. A rib does not either, and the model now says how far from least it would have to go: sixteen yarn diameters of bed gap before the yarn runs out, against the two or three a machine is set to.

 What a knitted band presses a limb with. Pressure against extension for a 20 tex cotton band at a 3.5 mm loop, wrapped round a 30 mm radius — a wrist. The pressure is the fabric's own tension per unit width divided by that radius, and the tension is the loop's bending with the relaxed shape as the yarn's natural one, so nothing here is fitted. Over the range a cuff is actually used across it runs from a twentieth of a millimetre of mercury to 0.85. The shaded bands are what a compression garment is specified at, and the curve does not reach the lowest of them until 277 per cent — which is not a cuff, it is a fabric stretched almost to the point where its yarn runs straight. Cloth doing a job

What a cuff presses with

A rib cuff holds a sleeve on a wrist, so it must be pressing. Divide its own recovery force by the radius it is wrapped round and the pressure comes out at eight tenths of a millimetre of mercury — a fiftieth of the lightest medical compression, and two orders below what the same fabric resists being squashed with.

 A rib crosses a gap where a jersey crosses a diameter. A one-by-one rib in section across 5 wales, drawn at a bed gap of 3 yarn diameters — 0.501 mm — because the relaxed gap of a rib is a measurement this collection does not hold and every figure of one says what it was drawn at. Alternate wales sit on opposite beds, so every sinker loop between them travels the whole gap. In a jersey the same yarn climbs one diameter, 0.167 mm. That single difference takes the contact force from 38.30 mN at 11.7° out of the fabric to 72.51 mN at 16.2°, and the through-thickness part from 7.81 mN to 20.17 mN. Cloth doing a job

A run cannot cross a bed

A dropped stitch unroves because its neighbour above can pull it out along a path that costs almost nothing. In a rib the neighbour above is on the other bed, and the path goes through the gap — so a run in a two-bed fabric has to pay for a climb before it can take a single loop.

 A knitted loop is a plane curve in a plane that is not the fabric's. A relaxed 20 tex jersey at a 3.5 mm loop, seen from the end of a course. Each course is a straight line because it is one: a half period leaves and arrives along the course direction, so the plane it bends in contains that direction, and a plane curve seen along a line in its own plane projects to a segment. The upper panel expands the thickness 3× so the arrangement can be seen and no angle may be measured off it; the lower panel is the same fabric at one scale, where the tilt is what it really is. The angle is 11.75°: a climb of one yarn diameter, 0.167 mm, against a drop of a course spacing and a diameter, 0.803 mm. Successive courses overlap by exactly one diameter, which is the interlacing, and the fabric is therefore 0.334 mm thick — two yarn diameters, with nothing fitted. Mechanics and drape

A loop is a plane curve in another plane

A knitted loop was solved as a flat curve because two curves in one plane cannot pass through one another and a loop must. Letting it out of the plane turns out to change nothing about its shape: the loop is still planar, and its plane is the fabric's turned through twelve degrees.

 What leaving the plane costs, which is less than nothing. Bending energy a stitch against how far the yarn climbs between one interlacing and the next, for a 20 tex cotton jersey at a 3.5 mm loop. The curve falls. A climb is not an extra bend added to a curve that was otherwise unchanged; it is part of the straight line the thread has to span, so a longer climb leaves less slack to be spent on curvature. At a jersey's own climb of one diameter the energy is 24395 nJ against 25060 for the planar model — 2.7% lower, where an earlier estimate on this site put the ride at three per cent of the loop's bending and had the sign the other way round. At a rib's climb of three or four diameters the fall is 33%. Mechanics and drape

What leaving the plane costs

Every number the flat loop model produced, beside the same number with the climb in it. Four of the five fall, none moves by four per cent, and the estimate that priced the third dimension beforehand had the sign the wrong way round for a reason worth naming.

 The force at an interlacing, which no longer lies in the fabric. A crossing of a relaxed jersey in section on the left, with the thickness expanded 3×, and on the right the contact force drawn at the angle the solve gives it — which is a true angle, unlike anything in the section beside it. The head of one course and the feet of the next lie one yarn diameter apart through the fabric, 0.167 mm, so the interlacing is not a point in a plane and the force at it is not in one either. It comes out at 38.30 mN a stitch, turned 11.75° out of the fabric: 37.50 mN along the wales, which is what friction has to hold, and 7.81 mN through the thickness, which is what holds the two faces apart. Divided by the area a stitch occupies the second is 15.1 kPa, or 113 mmHg — a pressure, and the quantity a compression measurement reports. Mechanics and drape

The force that holds a knit open

Resolving a knitted loop's contact force out of the fabric's plane leaves a fifth of it pointing through the thickness. That fifth is 7.8 millinewtons a stitch, fifteen kilopascals over the area a stitch occupies, and it is the whole reason a jersey has a thickness rather than a plan.

 How little eccentricity a curl needs. The radius a jersey would curl to, against how far the fabric's neutral surface fails to bisect its loops. The model's own loop is bisected exactly — its crest sits half a diameter behind the mid-surface and its trough half a diameter in front — so it carries no curling moment at all, and the curve here is what any departure from that would buy. The moment is proportional to the eccentricity, so one solve settles the whole curve. A radius of three millimetres, which is about what a fine jersey rolls to, needs 5.6% of a yarn diameter — 9.4 micrometres on a yarn 167 micrometres across. That is why curl is easy to see and hard to model: the whole of it lives inside a rounding error on the geometry. Only the course-wise edges are drawn, because bending about the other axis turns the thread's end tangents out of the fabric and a free thread given turned ends buckles clean out of it — 3.2 times the fabric's own thickness, for 37% off its energy. That configuration is not available to a thread with neighbours, so the second moment is refused rather than computed. Mechanics and drape

How little asymmetry a curl needs

A model with a thickness can finally be asked why stockinette rolls. It answers that it does not — its curling moment is exactly zero, by a symmetry — and the useful part is what that costs to break: five per cent of a yarn diameter buys the whole of the curl anybody has ever seen.

 A tube of an elastic band knitted 157 mm round, up one leg. A tube knitted 157 mm round from an elastic band, pulled up an illustrative leg and read at four stations. At each the tube is stretched by the leg's circumference over its own, pulls back with the band's tension at that stretch, and presses with that tension over the leg's radius: ankle 22 cm, stretched 40%, 20.0 mmHg; lower calf 29 cm, stretched 85%, 32.1 mmHg; calf 36 cm, stretched 129%, 39.4 mmHg; below the knee 34 cm, stretched 116%, 37.6 mmHg. The calf is pressed 1.97 times as hard as the ankle. What the bars cannot show is the leg's own give, which a firm tube flattens and which changes the radius the law divides by. Cloth doing a job

A tube of one size presses the calf harder than the ankle

A band presses a limb with its tension over the limb's radius, so it is easy to conclude that a band grips hardest where the limb is thinnest. That is true of a band held at one tension, and no knitted tube is. A tube knitted to one size is stretched further wherever the leg is thicker, and its tension rises faster than the radius does: an elastic tube pressing an ankle at twenty millimetres of mercury presses the calf at thirty-nine, and a cotton jersey tube presses its calf three and a half times as hard as its ankle. A stocking graduated the other way has to pull hardest where it presses less.

 What leaving the plane costs, which is less than nothing. Bending energy a stitch against how far the yarn climbs between one interlacing and the next, for a 20 tex cotton jersey at a 3.5 mm loop. The curve falls. A climb is not an extra bend added to a curve that was otherwise unchanged; it is part of the straight line the thread has to span, so a longer climb leaves less slack to be spent on curvature. At a jersey's own climb of one diameter the energy is 24395 nJ against 25060 for the planar model — 2.7% lower, where an earlier estimate on this site put the ride at three per cent of the loop's bending and had the sign the other way round. At a rib's climb of three or four diameters the fall is 33%. Mechanics and drape

What a knit gives up when it is pressed

The woven half of this collection has had a compression curve for several rungs — a thickness that falls under load, a bearing area that grows, a pressure at every point. The knitted half had a plan and no depth. It has a relaxed thickness and an initial slope now, and the two fabrics turn out to resist for different reasons.

The whole library · All essays